DYNOJET PC6-23016 Power Commander 6 Installation Guide

: June 3, 2024
: Dynojet

Table of Contents

PC6-23016 Power Commander 6
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
WIRE CONNECTIONS
INSTALLING THE POWER COMMANDER 6
Read User Manual Online (PDF format)
Download This Manual (PDF format)

POWER COMMANDER 6
Install Guide for: PC6-23016
Model coverage:
2017-2019 Husqvarna FE350
2017-2019 Husqvarna FE501
Installation Guide

PC6-23016 Power Commander 6

PARTS LIST

1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS| 2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
---|---

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

OPTIONAL ACCESSORY INPUTS

Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is set up you can alter your map based on gear position and setup gear-dependent kill times when using a quick-shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS

To input wires into the PC6 first remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tightens the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.

2 17-19 HUSQVARNA FE350/501

INSTALLING THE POWER COMMANDER 6

|
---|---
|

Remove the seat.
Remove the left and right side radiator shrouds.
Remove the fuel tank.
Use the supplied Velcro strips to secure the PC6 module to the top of the battery. Clean surfaces with the alcohol swab before attaching the Velcro.
Route the PC6 wiring harness upwards towards the battery staying inside of the frame rails.
Secure the PC6 ground wire with the small ring terminal to the negative (-) side of the bike’s battery.
Continue routing the PC6 wiring harness towards the left side of the engine. The harness branch with four connectors will need to go to the left side of the throttle body. The branch with only two connectors will go to the top of the cylinder head.
Unplug the Fuel Injector and the Throttle Position Sensor.
There is a plastic cover over the TPS. If you remove the bottom screw on this cover it will help.
Plug the pair of 3-pin connectors of the PC6 wiring harness in-line with the TPS.
Plug the pair of 2-pin connectors of the PC6 wiring harness in-line with the Fuel Injector. Replace the TPS cover if it was removed.
Unplug the stock Crank Position Sensor connectors.
This is a BLUE 2-pin connector pair located above the cylinder head.
Plug the PC6 wiring harness in line with the stock Crank Position Sensor connectors.
Reinstall the fuel tank, bodywork, and seat.
Affix the supplied CARB E.O. label to a conspicuous area. Next to the original emissions label is a good location. Make sure to clean the surface before attaching.