tp-link TL-WPA7617 Powerline Extender Installation Guide

: June 1, 2024
: tp-link

Table of Contents

TL-WPA7617 Powerline Extender
Unify Your Wi-Fi Networks
Sync Wi-Fi Settings to More Extenders
Personalize Your Networks
EasyMesh-Compatible
LEDs & Buttons
Frequently Asked Questions
Documents / Resources

Quick Installation Guide

TL-WPA7617 Powerline Extender

TL-WPA7617 (European version) is used for demonstration in this guide.
Images may differ from actual products.

tp link TL WPA7617 Powerline Extender

Plug in the new extender near one of your existing powerline devices.
Check the new extender’s Powerline LED . Is it on?
Yes > Step 4
No > Step 3
Pair the powerline devices.
A. Press the Pair button on the existing powerline device for 1 second. The Power LED starts blinking.
Note: If the Power LED does not blink, press the Pair button again.
B. Within 2 minutes, press the Pair button on the new extender for 1 second. The Power LED starts blinking.
When the Powerline LED on the new extender turns on, the pairing process is complete.
Enjoy!
Relocate the extender to the Wi-Fi “dead” zone. Connect your devices to the internet using the default SSIDs (network name) and password on the label at the side of the extender.

tp link TL WPA7617 Powerline Extender - extender

Tip:
If you cannot find the SSIDs in your Wi-Fi network list, your new extender has automatically copied over the existing wireless settings. In this case, use the SSID and password of your existing powerline network to connect. If you want to unify your Wi-Fi networks, refer to the back page for instructions.

Attention

Use the product only in the upright direction.
Plug powerline devices into wall outlets instead of power strips.
Note: Using power strip will affect network performance or even cause connection drops.

Unify Your Wi-Fi Networks

Copy SSID and password from your router via any of the methods below to create one unified Wi-Fi network throughout your home.
Note: If your router doesn’t support the two methods below, refer to Personalize Your Networks section to manually change the extender’s Wi-Fi settings.
Method ONE: Via Wi-Fi Button
Note: You can use this method when your router has a WPS button.

Plug in the extender in the same room as your router. Wait until the extender’s Wi-Fi LED turns on.
Press your router’s WPS button. (Within 2 minutes) press the extender’s Wi-Fi button for 1 second. The extender’s Wi-Fi LED starts blinking.
When it stays on, Wi-Fi settings are copied.
Note: If Wi-Fi settings are not copied within 2 minutes, manually change the extender’s Wi-Fi settings.
Relocate the extender and enjoy the internet using your router’s SSID and password.

tp link TL WPA7617 Powerline Extender - Relocate
extender

Method TWO: Via EasyMesh
Note: You can use this method when your router supports EasyMesh.

Connect your computer to the extender wirelessly. Visit http://tplinkplc.net.
Go to EasyMesh and enable it. Then the extender will automatically join an EasyMesh network and copy the wireless settings from the main router.
Enjoy the internet using your router’s SSID and password. Any changes to the Wi-Fi settings of your router will be automatically copied to the extender.

tp link TL WPA7617 Powerline Extender - Via EasyMesh

Sync Wi-Fi Settings to More Extenders

If you have paired your powerline devices, the Wi-Fi settings will automatically sync from the existing extender to the new one.
Note: For more extender models that support Wi-Fi Auto-Sync, visit http://www.tp-link.com.
If you personalize any extender with LED schedules or other Wi-Fi settings (such as Wi-Fi schedules and guest network), the settings will also automatically sync to other extenders in the secured powerline network.

tp link TL WPA7617 Powerline Extender - Extenders

Personalize Your Networks

Manage your powerline devices using any of the methods below. You can change the SSID and password, set Wi-Fi schedules, create a guest network and more.
tpPLC App
For easy management via your smartphone or tablet, download the app from Apple App Store or Google Play, or simply scan the QR code.

tp link TL WPA7617 Powerline Extender - QR Code https://www.tp-link.com/app/qrcode/?app=tp-plc

tpPLC Utility
For easy management via your computer, download the utility at https://www .tp-link.com/support/download/.
Note: For detailed instructions, refer to the utility manual on the product’s Support page.
Web Interface
To access all settings, connect to an extender wirelessly and visit http://tplinkplc.net.
Note: For detailed instructions, refer to the product manual on the product’s Support page.

EasyMesh-Compatible

You can experience strong, stable, and seamless wireless connections throughout your home with EasyMesh, a whole home mesh standard that works across different access points for ultimate flexibility.

Seamless Roaming
Connects mobile devices to your routers or extenders that provide the best coverage.
Devices compatible with EasyMesh also share a single Wi-Fi name so you stay connected in every room.
Easy Setup and Management
Easily set up and manage a unified Mesh network.
Flexible Scalability
Flexibly scale your home networking with different vendors,* different topologies, different Protocols and different product categories.

*TP-Link EasyMesh-compatible products can network with other devices that use EasyMesh. Failed connections may be due to firmware conflicts of different vendors.
The EasyMesh-Compatible function is still being developed on some models and will be supported in subsequent software updates. This product is compatible with standardized EasyMesh technology but has not obtained the Wi-Fi EasyMesh certification.
For more information, visit https://www.tp-link.com/easymesh/.

LEDs & Buttons

LED	STATUS	DESCRIPTION
Power	On

Blinking
Off| The powerline adapter/extender is on.
Pairing is in process.
The powerline adapter/extender is off.
Powerline| On
Off| The powerline adapter/extender is connected to a powerline network.
The powerline adapter/extender is not connected to any powerline network.
Ethernet| On/Off| The Ethernet port is connected or not connected.
Wi-Fi| On
Blinking
Off| The wireless function is enabled.
The powerline extender is syncing wireless network settings.
The wireless function is disabled.
ITEM| DESCRIPTION
---|---
Pair/Reset Button| Press and hold for 1 second to set up or join a secure powerline network.
Press and hold the Pair button for at least 6 seconds, then release the button to reset the adapter/extender to default settings.
Wi-Fi Button| Press for 1 second to start copying Wi-Fi settings from the router.
Press and hold for about 5 seconds to turn Wi-Fi on or off.
LED Button| Press to turn on or off the LEDs.

Frequently Asked Questions

How do I reset my extender to factory default settings?

Press and hold the Pair button for at least 6 seconds. Release the button and all LEDs turn off. When the LEDs turn back on, the reset process is complete.

What should I do if the Powerline LED is off?

A1. Try another wall socket and make sure all powerline devices are on the same service panel. A2. Try to set up a powerline network by pairing. Refer to the section above for instructions. A3. If the problem persists, contact our Technical Support.

What should I do if there is no internet connection in my powerline network?

A1. Make sure all powerline devices are on the same service panel. A2. Make sure the Powerline LEDs are lit on all of your powerline devices. If they are not, pair all devices again. A3. Make sure all devices are correctly and securely connected. A4. Check if you have an internet connection by connecting the computer directly to the modem or router.

What should I do if a successfully-paired extender does not reconnect after it is relocated?

A1. Make sure all powerline devices are on the same service panel. A2. Try to pair the extender again, and make sure the Powerline LED is on. A3. Check for possible interference due to a washing machine, air conditioner or other household appliances that may be too close to one of the powerline devices. Plug the appliance into the integrated electrical socket to remove the electrical noise if your powerline device has an integrated electrical socket.

For technical support, replacement services, user guides, and other information, please visit https://www.tp-link.com/support , or simply scan the QR code.
To communicate with TP-Link users or engineers, please join the TP-Link Community at https://community.tp-link.com.

tp link TL WPA7617 Powerline Extender - QR Code 2 http://www.tp-link.com/support

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp- link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca/

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use the device where wireless devices are not allowed.
Plug the powerline devices directly into the wall outlets but not the power strips.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.