CONDTROL Smart 60 Laser Distance Meter User Manual
- June 4, 2024
- CONDTROL
Table of Contents
CONDTROL Smart 60 Laser Distance Meter
Congratulations on your purchase of the laser distance meter CONDTROL SMART
60.
Safety instructions can be found at the end of this user manual and should be
carefully read before you use the product for the first time.
FUNCTIONS/APPLICATIONS
Laser distance meter SMART 60 is intended to measure distance, lengths,
heights, calculate the area and volume of measured objects as well as to carry
out indirect measurements (Pythagoras’ Theorem). The product is suitable for
use in both indoor and outdoor building areas.
SET
- Laser distance meter – 1pc.
- Carry pouch with a strap – 1 pc.
- User manual – 1 pc.
- Batteries LR3 (AAA) – 2 pcs.
SPECIFICATIONS
| Working range | 0,05 — 60 m* |
|---|---|
| Measuring accuracy | + 1,5 mm** |
| Smallest unit displayed | 1 mm |
Automatic shutdown Laser
Instrument| 45 sec 180 sec
Display backlight| V
Continuous distance measuring (Tracking)| V
Addition/Subtraction of measurements| V
Area/volume calculation| V
Indirect measurement (Pythagoras’ Theorem)| V
Laser type| 650 nm, < 1 mW, class II
Working temperature| 0 °C … +40 °C
Storage temperature| —20 °C … +60 °C
Battery| 105x47x27 mm
Dimensions| 83 r
Weight| 2×1,5 V AAA LR3 (alkaline)
Use a target plate to increase the measurement range during daylight or if the
target has poor reflection properties.
Accuracy can decrease in unfavorable conditions, such as intense sunshine or
when measurements are made against glossy or transparent surfaces, moving
objects, objects with a rough surface.
In unfavorable conditions or when measured distance is over 100 m the maximum permissible accuracy is calculated in the following way:
- ± (Y + 0,25хDх10-3) mm, where
- D (mm) – measured distance
- Y (mm) – permissible accuracy according to technical data.
INSERT/REPLACE BATTERIES
Insert the batteries, observing correct polarity. Use alkaline batteries only,
both batteries must be of the same brand with the same charge level. Charge
level is shown on display. Replace batteries when you see symbol on the
display.
SWITCH ON/OFF
To switch on the product press . The product will switch on and enter
measuring mode. To switch off the product press and hold .
In order to save battery power, the product will switch off automatically
within 3 minutes after the last operation.
PRODUCT DESCRIPTION
- Bubble level
- Display
- Switch on / activate laser beam/ measurement / continuous measurement (tracking).
- Addition/subtraction / switch on/off sound signal.
- Area/volume calculation/indirect measurement (Pythagoras’ Theorem).
- Switch off/clear
- Strap location
Display
- The secondary line for displaying measuring results, maximal and minimal values.
- Symbol of Addition/subtraction mode
- A symbol indicating the area and volume calculation, indirect measurement mode.
- Mainline for displaying measuring results
- Battery charge level
- Reference point
- Unit of measurement
OPERATION
Reference point
It is possible to set the reference point – from the top or bottom end of the
product.
The default reference point is the bottom end of the product.
To select a reference point press and hold the button for 1 second. The
indicator will appear on the display.
Switch on/off the sound signal
To switch on/off the sound signal press and hold for 2 seconds.
MEASUREMENTS
Single distance measurement
Switch on the product. Short press to switch on a laser beam, point it at the
target, and press again for single distance measurement.
Short press to switch off the laser beam if it is on.
Continuous distance measurement (Tracking)
Press and hold . The product will take measurements one after another, showing
the last measured value. Besides it will show maximal and minimal measured
values.
To exit the mode press or .
CALCULATIONS
The last measurement can be canceled by and made again in modes of the area and volume calculation, indirect measurement mode (Pythagoras’ Theorem). If you double press in any of the above-mentioned modes, the product will enter a single distance measuring mode.
Addition/Subtraction
Addition/Subtraction function is used for the addition and subtraction of
lengths.
Make a single distance measurement, activate Addition/Subtraction mode by
short pressing , then make the next single distance measurement. The
calculation result will be shown in the mainline on the display. The next
measurements will also be added/subtracted to/from the next measuring result.
Press to exit
Addition/Subtraction mode.
Area
Press . A symbol will appear on display. Make 2 measurements one by one
(length and width). Area (composition of length and width) will be calculated
and shown in the mainline on the display.
Volume
Press twice . A symbol will appear on display. Make 3 measurements one by one
(length, width, height). Volume (composition of length, width and height) will
be calculated and shown in the mainline on the display.
Indirect measurement (Pythagorean Theorem)
If it is impossible to make a direct measurement (there is some obstruction)
required length can be calculated with the help of 2 others.
Press 3 times. A symbol will appear on display. Measure the length of segments A and B. Segment B must be perpendicular to segment C and can’t be longer than segment A. Length of segment C is calculated according to Pythagoras’ Theorem.
MESSAGE CODES
While operation, the following codes/symbols may appear on the display:
Message
| Cause|
Solution
---|---|---
301| Distance is out of range| Keep incorrect
measuring range
302| The reflected signal is too weak| Use reflecting plate
303| Measuring results cannot be displayed (negative or exceeds 99999)| Repeat
measurements
304| Pythagorean theorem calculation error| Make measurements incorrect
succession
305| Low battery| Replace batteries
306| Temperature is too low| Warm up the product
307| Temperature is too high| Cooldown the product
308| Ambient light is too strong| Make measurements in less illuminated zone
SAFETY REGULATIONS
The user manual should be read carefully before you use the product for the
first time. Unintended use of the product can be dangerous for human health
and cause serious injury.
Keep this user manual. If the product is given to somebody for temporary use,
be sure to enclose the user manual to it.
-
Do not misuse the product
-
Do not remove warning signs and protect them from abrasion, because they contain information about the safe operation of the product.
The device belongs to laser product class 2 in
accordance with EN 60825-1 with a 630670 nm wavelength. -
Do not look into the laser beam or its reflection, with an unprotected eye or through an optical instrument. Do not point the laser beam at people or animals without the need.
You can dazzle them. -
To protect your eyes close them or look aside.
-
It is prohibited to disassemble or repair the product yourself.
-
Intrust product repair to qualified personnel and use original spare parts only.
-
Do not use the product in an explosive environment, close to flammable materials.
-
Avoid heating the batteries to avoid the risk of explosion and electrolyte leakage. In case of liquid contact with skin, wash it immediately with soap and water. In case of contact with eyes, flush with clean water for 10 minutes and consult the doctor.
CARE AND MAINTENANCE
Attention! The instrument is a precision device and requires careful handling. The following recommendations will extend the life of the product:
- Do not point the product at the sun
- Protect the product from bumps, falls, excessive vibration; do not let liquids, construction dust and foreign objects get inside the product.
- Do not expose the product to extreme temperatures.
- If liquids get inside the product first remove the batteries, then contact a service center.
- Do not store or use the product under high humidity conditions for a long time.
- Clean the product with a soft wet cloth.
- Keep device optics clean and protect it from mechanical damage.
- Сarry out control measurements occasionally, especially if the product is subject to excessive mechanical or another impact, before and after taking important measurements.
UTILIZATION
Expired tools, accessories, and packages should be passed for waste recycling. Please send the product to the following address for proper recycling:
CONDTROL GmbH Wasserburger Strasse 9 84427 Sankt Wolfgang Germany
Do not throw the product in municipal waste!
According to the European directive, 2002/96/ЕC expired measuring tools and
their components must be collected separately and submitted to environmentally
friendly recycling of wastes.
WARRANTY
All CONDTROL GmbH products go through post-production control and are governed by the following warranty terms. The buyer’s right to claim about defects and general provisions of the current legislation do not expire.
- CONDTROL GmbH agrees to eliminate all defects in the product, discovered during the warranty period, that represent the defect in material or workmanship in full volume and at its own expense.
- The warranty period is 36 months and starts from the date of purchase by the end consumer (see the original supporting document).
- The warranty does not cover defects resulting from wear and tear or improper use, malfunction of the product caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of non-original accessories and spare parts. Modifications in the design of the product relieves the seller from responsibility for warranty works. The warranty does not cover cosmetic damage, which doesn’t hinder the normal operation of the product.
- CONDTROL GmbH reserves the right to decide on the replacement or repair of the device.
- Other claims not mentioned above, are not covered by the warranty.
- After holding warranty works by control GmbH warranty period is not renewed or extended.
- CONDTROL GmbH is not liable for loss of profit or inconvenience associated with a defect of the device, the rental cost of alternative equipment for the period of repair.
This warranty applies to German law except for the provision of the United
Nations Convention on contracts for the international sale of goods (CISG).
In warranty case please return the product to the retail seller or send it
with defect description to the following address:
CONDTROL GmbH
Wasserburger Strasse 9 84427 Sankt Wolfgang Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>