Eshare Technology EP01T Wireless Presentation System User Manual

Eshare Technology EP01T Wireless Presentation System User Manual

EP01T Wireless Presentation System
The user manual

ESHARE TECHNOLOGY CO., LIMITED

About this manual

The products described in this manual are for sale and use in mainland China only.
This manual is used as a guide. The photos, graphics, charts and illustrations provided in the manual, For the purpose of explanation and explanation only, there may be differences with the specific product, please refer to the actual product.

Declaration of responsibility

• Within the scope of the law allow maximum, this manual describes products(including its hardware, software, firmware, etc.) are provided “according to the status quo”, a possible flaw, error or malfunction, the company does not provide any express or implied warranty, including but not limited to, suitable for a particular purpose, merchantability, quality satisfaction without infringement of third party rights guarantee; No compensation shall be made for any special, incidental, incidental or indirect damages caused by the use of this manual or the use of our products, including but not limited to loss of business profit, loss of data or loss of documents.
• If you connect the product to the Internet, you need to take risks, including but not limited to the product may be subject to network attack, hacker attack, virus infection, etc., the company shall not be responsible for the abnormal product work, information leakage and other problems caused by this, but the company will provide you with timely technical support related to the product.
• Please strictly follow the applicable laws when using this product. The company does not accept any liability if the product is used for infringing the rights of third parties or other improper purposes.
• In the event of any conflict between the contents of this manual and the applicable law, the provisions of the law shall prevail.

Product introduction

Wireless Presentation System can realize automatic wireless screen projection, mirror screen projection, bidirectional control and other intelligent office meeting functions in a variety of platforms. From now on, we can avoid the complicated data line constraint, not be restricted by the distance, multiple people can cast, two-way operation, and realize efficient automatic, multi- person, multi-platform, and unconstrained intelligent meeting experience

The product adopts advanced drive free design, the access to the computer can automatically identify the system, automatically install the application, and start the application. Do not need tedious operation, can complete a key screen. The Wireless Presentation System can also receive touch feedback from the receiving end, feedback the touch operation to the PC, and realize the touch back function.

Figure 1 appearance of wireless projector and receiving box

(when used in conjunction with the conference tablet, all functions can be achieved by wireless projector only, no receiving box is needed)

The fuselage interface

FIG. 2 interface schematic diagram of wireless projector

FIG. 3 schematic diagram of receiving box interface

I、 Use with meeting tablet

1. Scheme 1: use wireless projector

• Meeting flat end pairing
  Connect the wireless projector to the USB port of the conference panel and wait for the device to pair automatically. The indicator light will change from the flashing state to the long-bright state, which means the match is successful.

After success, the main interface of the projection screen prompts that the pairing is successful, then pull out the wireless projector.

If the match is not successful, please contact our after-sales service for assistance.

Note: the device only needs to be paired once. If there is no change later, there is no need to re-pair.

• PC matching
  Equipment support Windows 7 system and above and Apple Mac OSX 10.10 system above.
  

The first step is to install the driver

When the wireless projector is connected to the PC’s USB interface, it will automatically start the installation driver software and start the application until the PC pairing is automatically completed.

When the PC system is set to turn off automatic playback of mobile devices, the automatic installation of the driver function will not berealized. At this point, manually open “ShareMax” in the root directory of the wireless projector storage space to install and pair with the PC.

The first time you use it, it takes about 1 minute to install the driver and about 20 seconds for subsequent use to start automatically and pair.

If the system prompts for permission or antivirus software, please choose to agree.

Step 2 open the projection screen

LED indication aperture flashing: indicates that the wireless transmitter is looking for the receiver;

LED indicates long and bright aperture: it indicates that the Wireless Presentation System is in the ready state and can transmit the screen at any time; At this time, press the Wireless Presentation System button to achieve the screen function.

Figure 4. Open the wireless projection screen

Step 3: end the projection

Press the wireless projector button again to end the projection.

2. Plan 2: use with mobile devices

a) Android devices

• Support Android system 2.3 or above
• Scan the qr code below to download the relevant application

• Open the wireless hotspot of the conference tablet and record the wireless hotspot name and password
• Open WIFI on Android device and search for WIFI hotspot ShareAP- (” ShareAP- “depends on the hotspot name of the actual device)
• Enter the account password of WIFI hotspot, the default passwordis12345678
• Open the downloaded APP, and the device number will bed is played at the top of the page, which represents the successful connection. The main interface will prompt the name of the current login phone. If not, please click refresh and select the current device name to login.

b) Apple devices

• Support Apple iPhone IOS 8.0 and above, Apple iPad IOS8.0andabove

• Open the wireless hotspot of the conference tablet and record the wireless hotspot name and password

• Open Apple device WIFI and search WIFI hotspot ShareAP- (” ShareAP- “depends on the hotspot name of the actual device)

• Enter the account password of WIFI hotspot, the default passwordis12345678

• Select the screen image in the control center of the Apple device and begin the wireless projection.

• note: when the “four-screen” option is enabled in the EShare software Settings of the conference tablet, up to four devices can be displayed at the same time. When there are more than four devices, the later devices will replace the earliest connected devices.

II、 Use method of matching display device

1) Displays device side connections
The first step is to connect the display device (projector, monitor) to the receiving box

Plug one end of the HDMI connector into the display device(projector, monitor) and the other end into the HDMI connector in the receiving box

FIG. 5 wiring diagram of receiving box and display equipment

Step 2 boot the receiver box

Long press the power on key of the receiving box for 3 seconds to start the machine. After starting the machine, the power lamp will show the blue color and the program interface will appear on the screen of the display device (projector, monitor).

The third step is to pair the receiving box with the display device

Connect the wireless projector to the USB port at the back of the receiving box and wait for the device to pair automatically. The indicator
light will change from the flashing state to the long-bright state, which means the pairing is successful.

After success, the main interface of the projection screen prompts that the pairing is successful, then pull out the wireless projector.

If the match is not successful, please contact our after-sales service for assistance.

Note: the device only needs to be paired once. If there is no change later, there is no need to re-pair.

2) PC matching
Equipment support Windows 7 system and above and Apple MacOSX 10.9 system above.

The first step is to install the driver

When the wireless projector is connected to the PC’s USB interface, it will automatically start the installation driver software and start the application until the PC pairing is automatically completed.

When the PC system is set to turn off automatic playback of mobile devices, the automatic installation of the driver function will not berealized. At this point, manually open “ShareMax” in the root directory of the wireless projector storage space to install and pair with the PC.

The first time you use it, it takes about 1 minute to install the driver and about 20 seconds for subsequent use to start automatically and pair.

If the system prompts for permission or antivirus software, please choose to agree.

Step 2 open the projection screen

LED indication aperture flashing: indicates that the wireless transmitter is looking for the receiver;

LED indicates long and bright aperture: it indicates that the Wireless Presentation System is in the ready state and can transmit the screen at any time; At this time, press the Wireless Presentation System button to achieve the screen function.

Figure 8 open the wireless projection screen

Step 3: end the projection

Press the wireless projector button again to end the projection.

III、 Product parameters

1. Wireless projector parameters

Configuration installation configuration free, automatic connection, automatic operation

Power/power consumption 5V, 0.5w ~2W
Interface HDMI + USB device
Support Windows 7/8/10, IOS 8.0, android 2.3 or above
Resolution 1080 p
The frame rate of 25 ~ 30 FPS
Transmission delay < 200 ms
Touch return support 10 point touch return (Windows, Mac)
Support mouse mode return (Windows, Mac)
WIFI type 2.4g /5G dual-frequency WIFI, The wireless rate is > 400 Mbps
Wireless transmission protocol IEEE 802.11a /g/n/ac
Band 5.8 G
Encryption AES
Verify protocol wpa2-psk

2. Receiving box parameter

Master RK3288
DDR 2 gb DDR3
8 gigabytes of storage
Power DC5V, 2.5 A
Operating system Android 5.1
The fuselage interface
HDMI 1
USB 2
Headphone jack 1
Power interface 1
Rj45 1

Infrared support
HDMI output
Supports 720P/1080P/2K/4K resolution
Support ratio 4:3, 16:9 (special ratio can be manually matched)
WIFI type 2.4g /5G dual-frequency WIFI, The wireless rate is >, 200 Mbps*2
Wireless transmission protocol IEEE 802.11a /g/n/ac
WIFI working mode STA and AP work simultaneously
Encryption AES
Verify protocol wpa2-psk

Audio/video

Video decoding Support h. 263, h. 264, h. 265, VP8, RV, WMV, AVS, MPEG4
Decoding resolution 720P/1080P/2K/4K
Touch support
The interface of USB HID
Mouse support
Laser touch support
Operating temperature -20℃~70℃
Infrared touch support
Capacitive touch support

Restricted substance or element identification table

“Administrative measures for the restricted use of harmful substances in

electrical and electronic products

The warranty service

Dear users:

Thank you for choosing this product. In order to fully enjoy the perfect after-sales service support, please read the instructions of this product warranty card carefully after purchase and keep it properly.

1. With this card to enjoy the warranty period of free warranty and warranty period of preferential services.

2. Free replacement period of 7 days from the date of purchase due to quality problems, and the warranty period of 2 years.

3. Prior to new product information or promotional opportunities.

4. Product failure caused by the following circumstances is not covered by the warranty:
   − Cannot produce valid warranty certificate and valid purchase invoice or receipt.
   − Improper use of the environment or conditions, such as power supply, ambient temperature, humidity, lightning strike and soon, resulting in product failure.
   − Product failure due to accident, negligence, disaster, improper or wrong operation, network attack, etc.
   − Failure or damage caused by installation, repair, alteration or disassembly by maintenance personnel not authorized by the company. − The product exceeds the warranty period stipulated by the company.

5. When the user has any objection to the technical service provided by the distributor, he can complain to the manufacturer’s customer support service center.

6. The warranty card shall be valid only after being sealed by the warranty unit.
   − User name: detailed address:
   − Telephone: fax: zip code: E-mail:
   − Product Model: product no. (S/N) :
   − Date of production: date of purchase: date of purchase
   − If you have other requirements, please fill in below

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>