CONDTROL Rotary laser Easy Roto HVR User Manual

CONDTROL Rotary laser Easy Roto HVR User Manual

User manual

Congratulations on your purchase of rotary laser Easy Roto HVR CONDTROL. Safety instructions can be found in the end of this user manual and should be carefully read before you use the device for the first time.

SAFETY INSTRUCTIONS

Attention! This user manual is an essential part of this instrument.
The user manual should be read carefully before you use the instrument for the first time. If the instrument is given to someone for temporary use, be sure to enclose user manual to it.

• Do not misuse the instrument.
• Do not remove warning signs and protect them from abrasion, because they contain information about safe operation of the instrument.
  • Laser radiation!
  • Do not stare into beam Class 2 laser
  • <1 m W 630-685 nm EN60825-1:2007-03
• Do not look into the laser beam or its reflection, with unprotected eye or through an optical instrument. Do not point the laser beam at people or animals without the need. You can dazzle them.
• To protect your eyes close them or look aside.
• Always install the instrument in such a way, so that laser line is below or above eye level.
• Do not let unauthorized people enter the zone of operation.
• Store the instrument beyond reach of children and unauthorized people.
• It is prohibited to disassemble or repair the instrument yourself. Entrust instrument repair to qualified personnel and use original spare parts only.
• Do not use the instrument in explosive environment, close to flammable materials.
• Laser intensive glasses are used for better recognition of the laser beam; do not use it for other purposes. Laser glasses do not protect from laser radiation as well as ultraviolet radiation and reduce color perception.
• Avoid heating the batteries to avoid the risk of explosion and electrolyte leakage. In case of liquid contact with skin, wash it immediately with soap and water. In case of contact with eyes, flush with clean water during 10 minutes and consult a healthcare practitioner.

INTENDED USE

Easy Roto HVR CONDTROL is a self-levelling rotary laser designed specially for professionals in construction works, repair, landscape design for projection of horizontal or vertical plane and laser dots (zenith and nadir). This rotary laser has a wide range of functions, it is easy to use and features other significant characteristics:

• Horizontal and vertical self-leveling
• Operation by buttons on control panel and remotely by the free App “Roto Remote” via Bluetooth
• Laser receiver included in the package increases the working range to 400m (in diameter)
• The accuracy is 3 times higher than that of line lasers.
• Shock-resistant, well protected from dust and moisture.
• Li-ion battery.

Rotary laser is suitable for use on both indoor and outdoor construction sites.

TECHNICAL SPECIFICATIONS

90°; 180°

Laser type| Class II 630-685 nm < 1 m W
Operating temperature| -200C ~ +500C
Storage temperature| -200C ~ +500C
Power supply of rotary laser| 2 x 4000mah Li-ion 7,4V rechargeable battery
Power supply of laser receiver| 1 x 6F22 9V
Battery life| 35h
IP rate| IP55
Type of tripod thread| 5/8″
---|---
Dimensions| 150 X 128 X 161 mm
Weight| 1,5 kg

DELIVERY PACKAGE

• Rotary laser – 1 pc.
• Universal mount – 1pc. Charger – 1 pc.
• Laser receiver – 1 pc.
• Mount for laser receiver – 1 pc. Glasses – 1 pc.
• Magnetic target board – 1 pc. User manual – 1 pc.
• Plastic case – 1 pc.

PRODUCT DESCRIPTION

1. Laser exit window
2. Rotating laser head
3. Laser dot exit window (zenith)
4. Control panel
5. Charging jack
6. Tripod thread 5/8” /laser dot exit window (nadir)

Control panel

1. Switch on/off the rotary laser

2. Switch on/switch off manual mode

3. Stop self-leveling after misalignment of the rotary laser

4. Adjust the slope along the axis X

5. Adjust the slope along the axis Y

6. Move the laser dot/scan sector clockwise

7. Move the laser dot/scan sector counterclockwise

8. Scanning mode/select scan sector

9. Select rotation speed
   LED indicators

10. Power

11. Manual mode

12. Stop self-leveling after misalignment of the rotary laser

Laser receiver

1. LCD:
2. Indication of accuracy
3. Indication of movement direction
4. Indication of detected laser line
5. Indication of battery charge level
6. Indication of audio signal
7. Receiver sensor
8. Keyboard:
9. Switch on/off audio signal
10. Select high/normal accuracy
11. Switch on/off
12. Level marks
13. Buzze

OPERATION

Battery charging

The rotary laser is powered by Li-ion rechargeable batteries. If the power indicator starts flashing during operation, the battery must be charged. Use the charger, included in the delivery package, for charging of Li-ion batteries. It takes about 5 hours to fully charge the battery. Light indicator on the charger will be red while charging. When light indicator on the charger turns green, the battery is full. Disconnect the charger. The batteries should be charged at least every three months so as to extend the battery service life.

Replace batteries in laser receiver
Laser receiver is powered by 6F22 9V included in the delivery package. Battery compartment is located on the back side of laser receiver. Open the battery cover, install the battery, observing correct polarity. Close the battery cover. Replace the battery as soon as the symbol of battery charge level becomes empty on the LCD . Use battery 6F22 9V only. Remove the battery from laser receiver if it is not used for a long time to avoid corrosion and battery discharging.

• Switch on/off the rotary laser Short press the button to switch on/off the laser.
• When the laser is switched on, the power indicator turns red and switch off when the laser is off.
• Switch on/off the laser receiver Short press the button to switch on/off the laser receiver.
• Audio signal in laser receiver By default, the sound indication is on – the symbol is on the display. Press to switch on/off sound indication.
• Detecting accuracy in laser receiver Press to select the accuracy:
  • high (±1.5mm/50 m)
  • standard (±3 mm/50 m)

OPERATION MODES

Self-leveling mode

Place the instrument on a flat surface, tripod 5/8” or universal mount. Switch on the laser. As soon as self-leveling is finished the head starts rotating clockwise at 600 If the slope of the rotary laser flashing, the head won’t rotate. Switch off the laser, set it on the surface and switch it on again.

• Short press the button to switch off self-leveling after the laser is misaligned. Indicator will be flashing green. If the rotary laser is unbalanced by some external influence, the laser will not align. Switch off the laser, then switch it on again and repeat operation.

Manual mode
This mode allows to project plane at any slope. Place the rotary laser on a solid and flat surface. Switch on the laser. Power indicator will turn red. The laser beam will be flashing while self-leveling. As soon as self-leveling is finished, the head will start rotating clockwise at 600 rpm. Short press the button to activate manual mode. The laser will switch to manual mode; indicator of manual mode will switch on. Set the device at the desired angle and fix its position. Short press to exit manual mode. Manual mode indicator will switch off. Projection of inclined laser line (axis X and Y) It allows to project inclined horizontal laser plane tilted up to ±10% for the axes X and Y. Place the instrument on a solid and flat surface.

1. Operation by buttons on control panel
   Switch on the laser. Power indicator will turn red. The laser beam will be flashing while self-leveling. As soon as self-leveling is finished, the head will start rotating clockwise at 600 rpm. Short press the button to activate manual mode. The laser will switch to manual mode, indicator of manual mode will switch on.  Short press the buttons to set required tilt along the axis Y. Short press the buttons to set required tilt along the axis X. As soon as the rotating head assumes desired position, it will start rotating at 600 rpm. Short press the button to exit the manual mode. The to exit the manual mode. The  manual mode indicator will switch off.

2. Operation by the App “Roto Remote” via Bluetooth Switch on the laser. Switch on Bluetooth in your smartphone. Start the APP “Roto Remote”. The app will detect the rotary laser automatically. After successful connection of the app with the rotary laser select

   • in the app menu. Tap or short press the button on the rotary laser to activate manual mode.

The laser will switch to manual mode. Indicator of manual mode will be green.

• Tap to adjust the slope for the axis Y. Tap to adjust the slope for the axis X.
  Tap or short press the button manual mode. adjust the slope for the axis X.

• • Tap or short press the button manual mode.

Laser dots
This laser can project laser dots (zenith and nadir). They are always on as long as the laser is on too.

Rotation speed

1. Operation by buttons on control panel Rotation speed 600 rpm is set by default.
   • Short press Short press speed will change in the following way: 600-0-120-300-600 rpm.
2.  Operation by the App “Roto Remote” via Bluetooth Switch on the laser. Switch on Bluetooth in your smartphone. Start the APP “Roto Remote”. The app will detect the rotary laser automatically. After successful connection of the app with the rotary laser select .

Tap repeatedly to change the rotation speed. Rotation speed set by default is 600 rpm. Rotation speed will change in the following way: 600-0-120-300-600… rpm. Attention! The slower rotation speed, the brighter the laser beam.

Scan mode

1. Operation via control panel of rotary laser
   • Short press to activate the scan mode. Press  repeatedly to select the scan sector – 0°, 10°; 45°; 90°; 180°.
   • Short press to move the scan sector counterclockwise,
   • short press to move the scan sector clockwise.
2. Operation by the App “Roto Remote” via Bluetooth Switch on the rotary laser. Switch on Bluetooth in your smartphone. Start the APP “Roto Remote”. The app will detect the rotary laser automatically. After successful connection of the app with the rotary laser select .

Tap repeatedly to select the scan sector – 0°, 10°; 45°;  90°; 180°. Tap and to move the scan sector counterclockwise accordingly.

Operation with laser receiver

Use mount included in the delivery package, to fix laser receiver on telescopic leveling staff. Switch on the laser receiver. Place the laser receiver in front of the laser beam. Move the detector up / down following the arrows on the LCD (front or back, whichever is more convenient). A down arrow on the display indicates that the receiver should be moved down; an up arrow indicates that the receiver should be moved up. When the laser beam hits the center of the receiver sensor and position of the laser beam coincides with levels marks, the receiver emits audio signal (if the audio signal is switched on) and symbol of detected laser line appears on the display.

Magnetic target board

A magnetic laser target will help to mark up ceiling systems or frame structures, such as drywall. The built-in magnet allows to fix the target on the ceiling rails or on the frame profile. The target has a linear marking on its surface, which helps to determine deviation from the nominal level and transfer control points while marking.

ACCURACY CHECK

Axis X

1. Place the instrument at 0.5 m distance to one wall and 10 m distance to another wall, so that axis X is aimed at the wall.
2.  Switch on the instrument. As soon as self-leveling is finished, mark location of laser beam on both walls by points X1 and X2.
3. Switch off the instrument. Move it to the opposite wall. Don’t change the position of the instrument.
4. Switch on the instrument. Align laser line with the previously made point X2. Mark point X3 on the opposite wall.
5. If distance between points X1 и X3 is more than 3 mm – switch off the instrument and contact service center.

Axis Y

1. Place the instrument at 0.5 m distance to one wall and 10 m distance to another wall, so that axis Y is aimed at the wall.
2. Switch on the instrument. As soon as self-leveling is finished, mark location of laser beam on both walls by points Y1 and Y2.
3. Switch off the instrument. Move it to the opposite wall, position of the instrument should remain unchanged.
4. Switch on the instrument. Align laser line with the previously made point Y2. Mark point Y3 on the opposite wall.
5. If distance between points Y1 и Y3 is more than 3 mm – switch off the instrument and contact service center. Place the instrument at 0.5m distance to one wall and 10m distance to another wall, so that axis Y is aimed at the wall. Switch on the instrument. As soon as self-leveling is finished, mark location of the laser beam on both walls by points Y1 and Y2. Switch off the instrument. Move it to the opposite wall, position of the instrument

CARE AND MAINTENANCE

Rotary laser is a high-precision instrument and requires careful handling. Before using as well as after physical impact (falling, hitting) carry out accuracy check. Observation of the following recommendations will extend the life of the device:

1. Store the instrument, spare parts and its accessories beyond reach of children and unauthorized people.
2. The instrument should be transported in the off state inside the case only.
3. Do not store the instrument in dusty or dirty locations. The instrument is dust and dirt resistant, but long-time exposure to these elements may damage internal moving parts of the instrument.
4. Store the instrument in dry locations. The instrument is water resistant, but precipitate, humidity and liquids containing minerals may damage the electrical circuits of the instrument. Do not try to dry the instrument by fire or a hairdryer.
5. Do not store the instrument in locations where temperature is more than +50°С. High temperatures reduce the life of electronic devices, damage batteries, deform or melt plastic parts.
6. Do not store the instrument in locations where temperature is less than -20°С. After storage in low temperature conditions and subsequent transfer to a warm room, the instrument is heated, causing moisture condense inside the instrument and damage the electronic components.
7. Protect the instrument from bumps, drops, strong
8. Carry out accuracy check regularly (see paragraph «Accuracy check»).
9. To clean the instrument use a soft wet cloth. Do not use harsh chemicals, cleaning solvents or detergents.
10. Сlean laser aperture regularly with a soft lint-free cloth with isopropyl alcohol.
11. Remove batteries from the instrument if it not used for a long time.
12. Do not leave discharged batteries in the instrument.

UTILIZATION

Expired tools, accessories and package should be passed for waste recycle. Please send the instrument to the following address for proper recycling:

• CONDTROL GmbH I’m Weidenfeld 4 85570 Market Schwaben Germany

Do not throw the instrument in municipal waste! According to European directive 2002/96/ЕC expired measuring tools and their components must be collected separately and submitted to environmentally friendly recycle of wastes.

WARRANTY
All CONDTROL GmbH products go through post-production control and are governed by the following warranty terms. The buyer’s right to claim about defects and general provisions of the current legislation do not expire.

1. CONDTROL GmbH agrees to eliminate all defects in the product, discovered while warranty period, that represent the defect in material or workmanship in full volume and at its own expense.
2. The warranty period is 24 months and starts from the date of purchase by end customer (see the original supporting document).
3. The warranty doesn’t cover defects resulting from wear and tear or improper use, malfunction of the product caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of non-original accessories and spare parts. Modifications in design of the product relieve the seller from responsibility for warranty works. The warranty does not cover cosmetic damage, that doesn’t hinder normal operation of the product.
4. CONDTROL GmbH reserves the right to decide on replacement or repair of the device.
5. Other claims not mentioned above, are not covered by the 3) The warranty doesn’t cover defects resulting from wear and tear or improper use, malfunction of the product caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of non-original accessories and spare parts. Modifications in design of the product relieve the seller from responsibility for warranty works. The warranty does not cover cosmetic damage, that doesn’t hinder normal operation of the product.
6. CONDTROL GmbH reserves the right to decide on replacement or repair of the device. Other claims not mentioned above, are not covered by the warranty.
7. After holding warranty works by CONDTROL GmbH warranty period is not renewed or extended. CONDTROL GmbH is not liable for loss of profit or inconvenience associated with a defect of the device, rental cost of alternative equipment for the period of repair.

This warranty applies to German law except provision of the United Nations Convention on contracts for the international sale of goods (CISG). In warranty case please return the product to retail seller or send it with description of defect to the following address:

CONDTROL GmbH

• I’m Weidenfeld 4
• 85570 Market Schwaben
• Germany

References

• Интернет магазин производителя лазерных измерительных приборов Condtrol

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>