35Z DucoGrille Close Instruction Manual

Table of Contents

35Z DucoGrille Close Instruction Manual

Fixing lug, Duco Close 35Z+
G 0009681
Parts List

Blind rivet Ø3×6
G 0000061
Parts List

Self-drilling screw 3.5×16 DIN 7504
GODODOBO

DucoGrille Close 35 is available with different frames and in different sizes:

For a G grille or an N grille, allow an opening in the wall that is at least 10 mm larger in height and width than the grille.

FRAME	TYPE	MINIMUM WIDTH	MINIMUM HEIGHT
F24	Window louvre glass size 24 mm	160 mm	263,5 mm
F28	Window louvre glass size 28 mm	160 mm	263,5 mm
G	Recessed mounting louvre with flange	160 mm	263,5 mm
N	Recessed mounting louvre without flange	160 mm	263,5 mm

Cordillera Close 35 is available with different controls::

Cord

Rod

Mounting a Cordillera Close 35 is dependent on the frame:

FRAME	TYPE	Mounting	PAGE
F24	Window louver glass size 24 mm	Replacement for 24 mm glass	5
F28	Window louver glass size 28 mm	Replacement for 28 mm glass	5
G	Recessed mounting louver with flange	On exterior wall	6
N	Recessed mounting louver without flange	On external louver grille of
choice On internal wall (with external louver grille of choice)	7

8

Mark the position of the fixing lugs (G 0009681) on the sides of the frame in the drilling groove provided:
- 1 fixing lug per side at 100 mm from the top of the frame
- 1 fixing lug per side at 100 mm from the bottom of the frame
- provide additional fixing lugs if the distance between two fixing lugs exceeds 350 mm
NB! Only drill through the outer frame.
Drill Ø3 mm holes, 2 mm deep, for fixing the fixing lugs.
Fix the fixing lugs using the blind rivets (G 0000061).
Apply transparent silicone on the inside of the flange.
Mount the grille in the opening provided and fix the fixing lugs with an appropriate fastener for the substrate.
Apply transparent silicone to the outside of the grille.

For mounting on outer grille of choice

NB! The cover sections are to be refitted after fixing the grille.
Remove the cover sections on the sides of the frame.
NB! Drill only on the side mounted against the external louver grille. Drill Ø4 mm holes in the drilling groove provided:
- 1 hole per side at 50 mm from the top of the frame
- 1 hole per side at 50 mm from the bottom of the frame
- provide additional holes if the distance between two holes exceeds 350 mm
Mount the Cordillera Close 35 on the back of the outer grille and fix with the screws (G 0000080).
Refit the cover sections on the sides of the frame.
Mount the external grille in accordance with the corresponding instructions.

For mounting on internal wall

Mount the external grille in accordance with the corresponding instructions.
Bend the fixing lugs 90° to get the desired recess depth.
Mark the position of the fixing lugs (G 0009681) on the sides of the frame in the drilling groove provided:
- 1 fixing lug per side at 100 mm from the top of the frame
- 1 fixing lug per side at 100 mm from the bottom of the frame
- provide additional fixing lugs if the distance between two fixing lugs exceeds 350 mm
NB! Only drill through the outer frame. Drill Ø3 mm holes, 2 mm deep, for fixing the fixing lugs.
Fix the fixing lugs using the blind rivets (G 0000061).
Mount the grille in the opening provided and fix the fixing lugs with an appropriate fastener for the substrate.
Finish the interior wall as you choose.