AUDIO ENHANCEMENT BEAM Pro Classroom System Wall Mount User Guide
- June 1, 2024
- AUDIO ENHANCEMENT
Table of Contents
BEAM Pro
Quick Start Guide
BEAM Pro Front
BEAM Pro Rear
TONE CONTROLS
Side Panel Connections
The
BEAM Pro has an output connection and level control designed to with work with
a student’s personal assistive listening device.
This is typically a small battery-powered FM transmitter and can be plugged
directly into the Assistive Listening Output.
A 3.5 mm to 3.5 mm cable is required to connect between the BEAM Pro and
student’s device. The Assistive Listening Output allows the level to be
optimized for the student’s device.
You will need to go into the menu of the student’s device and select the
external line input.
Basic Operation of Microphones
Press & hold the PWR button to turn the Mic on or off.
A momentary press of the PWR button will mute or unmute the microphone audio.
If muted for more than 5 minutes, the microphone will turn off automatically.
Teacher Microphone (OWN) Level Adjustment
Press either the UP or DOWN arrow button to increase or decrease the level of
the Teacher microphone. A blue LED under the OWN label (for own microphone)
will flash with each press.
Mic360 or Handheld Microphone (OTHER) Level Adjustment
To adjust the Mic360 or Handheld Microphone (OTHER) volume, first press the
SELECT button so that the LED under the OTHER label comes on. Now press the
UP/DOWN buttons to control the level of the OTHER microphone, which is
typically the Mic360. Media Input (LINE) Level Adjustment
Selecting the LINE audio source will control the volume of audio from devices
that are connected to the BEAM via 3.5 mm audio cable or TOSLINK optical
cable.
Charging the Teacher/Mic360 and Handheld Microphones
Teacher/Mic360 Microphone
Step 1—Connect the micro-USB plug of the charger to the DC input terminal of
the microphone.
Step 2—The charger indicator light will blink at 2-second intervals.
Step 3—The charger indicator light will remain on once fully charged.
Handheld Microphone
Step 1—Connect the micro-USB plug of the charger to the DC input terminal of
the microphone.
Step 2—The charger indicator light will blink at 2-second intervals.
Step 3—The charger indicator light will remain on once fully charged.
Pairing Microphones to the BEAM Pro
Any microphones purchased with the BEAM Pro should already be paired. You can check this by turning on your Teacher, Mic360 and Handheld Microphones (Teacher Mic: press PWR for 1 second; Handheld Mic: flip TALK switch up). If the LED under the BATT indicator turns green, the mic is paired. If the LED blinks another color (orange), then turn off your microphones and use the following instructions to pair them to the BEAM Pro. Teacher/Mic360 Microphone
- Turn mic off: press and hold PWR/MUTE until the green BATT light turns off.
- Press and release the XD LINK button on the side of the speaker.
- Press and hold the PWR/MUTE and REC buttons on the Teacher/Mic360 Microphone until a beep is heard from the speaker.
Handheld Microphone
Turn mic off: flip the TALK switch down.
The green BATT light will turn off.
Press and release the XD LINK button on the side of the speaker.
Press and hold the PWR/LINK button and TALK pushbuttons together on the
Handheld Microphone until a beep is heard from the speaker.
Pairing Media Microphone to the BEAM Pro
Ensure that two microphones are already paired to the BEAM Pro and turned on.
Turn mic off: flip the TALK switch down.
The green BATT light will turn off.
Press and release the XD LINK button on the side of the speaker.
Press and hold the PWR/LINK button and TALK pushbuttons together on the Media
Microphone until a beep is heard from the speaker. Pairing will take longer
than usual—approximately 10 seconds.
The LINK LED will now function as the Media Channel power indicator.
Wireless Pairing
-
Activate Wireless Audio on your device.
-
Press the pairing button on the side of the speaker (the blue LED in the switch will start flashing).
-
Select “AE_BLUE” from the menu on your device.
-
Volume of the input is controlled from the user’s device.
Typically this is the volume control on your phone. -
To pair a new device to the BEAM Pro, first disconnect the paired device, then follow the directions above for the new device.
-
Please Note: The BEAM Pro pairing button must be pressed each time a previously paired device is brought back into range of the BEAM Pro.
www.AudioEnhancement.com
800.383.9362
DC-40716.02
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>