EDILKAMIN DELUXE Wood Burning Stoves Instruction Manual

DELUXE Wood Burning Stoves
Instruction Manual

Installation, use and maintenance

DELUXE Wood Burning Stoves

Dear Sir/Madam
Congratulations and thank you for choosing our product.
Please read this document carefully before you use this product in order to obtain the best performance in complete safety.
For further details or assistance, please contact the DEALER where you purchased the product or visit the TECHNICAL ASSISTANCE CENTRES page on our website
www.edilkamin.com.
NOTE
– After you remove the packaging, please inspect the unit for any damage or missing parts (warranty booklet, glove, technical data sheet, spatula, desiccant, hex key).
In case of anomalies please contact the dealer where you purchased the product immediately. You will need to present a copy of the warranty booklet and valid proof of purchase.
– Commissioning/ Testing
Commissioning and testing must be performed by an authorized Edilkamin Technical Assistance Centre. Failure to do so will void the warranty.
Commissioning, as specified in standard UNI 10683 Rev. 2005 (section “3.2”) consists in a series of controls performed on the installed stove in order to ascertain the correct operation of the system and its compliance to applicable regulations.
To locate the Technical Assistance Centre closest to you, please ask your local dealer, call our toll-free number, or visit our website www.edilkamin.com.
– Incorrect installation, incorrect maintenance, or improper use of the product, shall relieve the manufacturer from any damage resulting from the use of this product.
– the proof of purchase tag, necessary for identifying the stove, is located:
– on the top of the package
– in the warranty booklet found inside the firebox
– on the ID plate affixed to the back side of the unit;
This documentation must be saved for identification together with the valid proof of purchase receipt. The data contained therein must be reported when requesting information and made available should servicing be required;
– All images are for illustration purposes only; actual products may vary.
DECLARATION OF CONFORMITY
The undersigned EDILKAMIN S.p.a. with head office headquarters at Via Vincenzo Monti 47 – 20123 Milan –Italy- VAT IT00192220192
Declares under its own responsibility as follows: the wood stove specified below is in accordance with the 89/106/CEE (Construction Products) WOOD STOVES, trademark EDILKAMIN, called DELUXE – DIAMOND
Model: DELUXE – DIAMOND
Serial number: Ref. data tag plate
Year of manufacture : Ref. data tag plate
The compliance with the 89/106/EEC directive is besides determined by the compliance with the European standard:  EN 13240:2006
EDILKAMIN S.p.a. will decline all responsibility of malfunctioning or damage to the equipment in case of unauthorized substitution, assembly or modifications of any sort on the said equipment on the part of non-EDILKAMIN personnel.

TECHNICAL FEATURES

• Structure and coating in grey-painted steel.
• Internal firebox in Vermiculite.
• Ash grate in cast iron and ash pan.
• Internal firebox width 38 cm, height 45 cm.
• Self-closing door.
• The smoke outlet from top or rear.
• Primary combustion air adjustment.

Obtained by moving the lever A (illustration 1-2): right open – left closed.
Primary air is used to manage flame intensity.

• Secondary combustion air adjustment.

Obtained by moving the lever B (illustration 1-2): right open – left closed.
Secondary air not only enables the ceramic glass to be cleaned, it also enables the combustion of any gases that could develop from the incomplete combustion of the wood,  thereby reducing the risk of hazardous gases entering the room. The preset amount of secondary air enters the firebox through a passage in the door’s upper glass retainer.

DIMENSIONS

ROTATION OF THE DELUXE STOVE
The DELUXE model is designed to rotate on its vertical axis by 360°. Before rotating make sure that the safety distances from flammable walls and/or heat- sensitive objects are complied with. The stove must only be rotated when cold!
* To rotate the stove, move the lever upwards to free the anti-rotation stop device.

SMOKE OUTLET

FLUE

• Before positioning the stove, make sure the flue is suitable for the smoke produced. The fact an old oven or stove connected to the same flue worked correctly does not necessarily mean the new one will work well.

• When installing the stove, the position of the flue must be taken into account in order to prevent incorrect smoke duct paths; the size of the flue must comply with the specifications indicated in the technical data. We recommend using insulated circular section flues made of refractory material or stainless steel with smooth internal walls. The flue cross-section should be constant for its whole length (we recommend a minimum height of 3.5 – 4 m).
  • We recommend fitting a chamber at the base of the flue to collect solid material and any condensation.
  Dilapidated flues and flues made of unsuitable materials (asbestos, galvanized steel, corrugated iron, etc.) with rough or porous internal surfaces are illegal and detrimental to
  stove operation.
  • The flue should be used for one single stove only (it cannot receive the outlet of other fireboxes)
  • For a good draught, the flue should be free from obstructions, such as bottlenecks, horizontal sections and sharp edges; any nonvertical sections should slope by not
  more than 45° from the vertical (fig. 3).

• If the flue to be used has previously been used for other stoves or fireplaces, it must be carefully cleaned to prevent faulty operation and avert the risk of unburnt deposits on the internal flue walls catching fire.

• In normal working conditions, the flue must be cleaned at least once a year.

• For optimal operation, the flue draught must create a pressure drop between 0.12 and 0.2 bars. Lower values may lead to unpleasant smoke emissions when loading the stove and produce excessive soot deposits; higher values would lead to excessively fast combustion and a decrease in thermal efficiency. To fall within the correct values, refer to the UNI Standard 10683/2006 table.

• If there are several flues on the roof, the others should be at least 2 meters away and the stove chimney pot should be at least 40 cm higher than the others. Please refer to the chapter of the UNI 10683/2006 regulation regarding the positioning of chimney pots.

• We recommend installing a fire damper on the smoke duct.

SMOKE DUCT
The smoke duct connects the smoke outlet to the flue inlet. The smoke duct must be made with steel or ceramic rigid pipes. Flexible metal pipes or fiber- cement pipes are not allowed. Horizontal and counterslope sections should be avoided. Any cross-section change should be made in correspondence with the stove outlet and not at the flue inlet.
Angles greater than 45° are not allowed (see Figure 1,2,3,4).
The connection between the smoke duct and the steel flue should be sealed with high-temperature-resistant mastic.
CHIMNEY POT
The chimney pot must have a wind guard (for any clarification, please refer to your retailer), an internal section equivalent to that of the flue, and a smoke outlet cross-section at least twice that of the internal flue cross- section. For correct operation, please refer to 10683/2006.
THERMO TECHNICAL CHARACTERISTICS

INSTALLATION

The stove is delivered on a pallet inside a cardboard box. First of all, remove the stove from its packaging, check that the model is the one ordered, and make sure it has not been damaged during transportation. Any complaints must be made to the carrier (in writing on the accompanying consignment note) upon receipt. Refer to the local regulations in the country of use for assembly and anything else not expressly shown. In Italy, refer to standard UNI 10683/2006, along with any regional or local health authority regulations. If the stove is to be installed in a condominium, consult the administration before installing it.

COMPATIBILITY WITH OTHER DEVICES

According to the regulation UNI 10683/05, the stove must NOT be installed in the same room as extractors, type B gas equipment or any device creating vacuum conditions. Warning: extraction fans operating in the same room can cause problems.
AIR INTAKE
The room of installation must have a suitable outside air intake with a thorough surface area of at least 200 cm² (Ø 16), in order to replenish the burnt oxygen and ensure an adequate combustion airflow. Alternatively, air can be drawn from the outside and conveyed through a Ø10 pipe connected directly to the rear of the stove ( ) as shown in illustration 1. To connect the pipe to the stove, eliminate the pre-carved cap ( ) and fit the pipe by means of a “spring wire” clamp, then fasten the pipe.

SAFETY DISTANCES

– Place the stove away from flammable materials and objects; keep a distance from the sides mobile version 20 cm for DIAMOND and 110 cm for the DELUXE version and at least 20 cm for both wall.
These distances are for furniture or walls which are either fireproof or able to withstand being raised to an environmental temperature of 80°C without overheating to the point of catching fire.
The air circulation which is created around the stove thanks to these distances ensures efficient ventilation and improves thermal efficiency.
– In the event the stove is to be installed on a floor made with flammable material, we recommend placing it on a steel plate available as an optional.
EDILKAMIN declines any responsibility for installations not complying with the laws in force and for misuse of the stove.
FIRE DAMPERS (with the installation of the damper on the smoke channel)
The fire damper should be easily handled and its position must be distinguished from the outside through the adjustment knob.
The fire damper must remain fixed in its position and must not be able to close automatically.
The fire dumper must NOT close the flue section completely, but it must guarantee a permanent minimum opening which should be equal to 3 % of the section itself and in any case equal to at least 20 cm².

INSTRUCTIONS FOR USE

NOTE on the fuel: wood
For the correct operation of the stove, it is necessary to burn dry natural wood, with a humidity of a maximum 20%.
Warning: while in operation, some parts of the stove reach very high temperatures; therefore, we recommend keeping a good eye on children.
The stove has been designed to work with the door closed only. Heat is propagated by radiation and convection. Always use the provided glove to open the door and to
make the adjustments.
FIRST LIGHTING
Any unpleasant odor or smoke could be caused by materials used during construction evaporating or drying. This tends to die down after a few days. Proceed as follows: put some paper with a small quantity of well-seasoned thin wood into the firebox, in order to live up the flame as much as possible, to make the flame as fierce as possible, opening the primary and secondary air dampers as much as possible (see illustration 1-2 on Pag. 9) and HALF-CLOSE the door.
– As soon as the flames have died down and have formed a hard bed of embers, load a normal amount of wood into the firebox (do not exceed the maximum amount specified
in the table on page 10).
– At this point close the door completely and adjust the combustion using the primary and secondary air dampers.
– Make sure the firebox door is always perfectly closed during operation.
NOTE:
do not use alcohol, petrol, kerosene, or other liquid fuels to light the fire. Keep liquid fuels away from the fire.
Do not use firelighters made from petroleum or chemical substances: they may cause serious damage to the firebox walls. Use eco-friendly firelighters only.
Overloading (in excess of 2.5 kg/h – see a table containing technical data) or excessively lively flames may damage the firebox compartment.
FUEL TYPE
This stove is preferably fed with well-seasoned beech/birch wood Each type of wood has different characteristics that also affect combustion efficiency. The declared nominal kW yield of the stove is obtained by burning the correct amount of wood, taking care not to overload the combustion chamber.
Fuel and heating power
Combustion has been optimized from a technical point of view both with regards to the design of the hearth and its air supply as well as in terms of emissions.
Please support our commitment to a clean environment by observing the directions listed below regarding the use of combustible materials that do not contain and do not produce harmful substances.
As far as fuel, use only natural and seasoned wood or wood briquettes. Wet or fresh-cut wood or wood stored improperly presents a high water content and therefore does not burn properly, creates smoke and produces little heat. Only use firewood that has been seasoned for a minimum of year two years in a ventilated and dry environment. In this case, the water content will be below 20% of the weight. This way you will save in terms of combustible material, as the seasoned wood has a much higher calorific value.
Never use liquid fuels such as gasoline, alcohol, or similar. Do not burn waste.
Note: Seasoned wood has a calorific value of approximately 4 kWh/kg, while fresh-cut wood has a calorific value of only 2 kWh/kg. Therefore, to achieve the same calorific value you would have to use double the fuel.

| Water content g/kg of wood| Calorific value kWh/kg| Higher wood consumption in %
---|---|---|---
Very seasoned| 100| 4,5| 0
2 years of seasoning| 200| 4| 15
1 year of seasoning| 350| 3| 71
Fresh-cut firewood| 500| 2,1| 153

ATTENTION: If the heart is fuelled by an excessive amount of fuel or improper fuel, the danger of overheating can occur with consequent damage to the product.

MAINTENANCE

Removing the ash
The ash pan contained within the firebox must be emptied as soon as it becomes close to being full of ash.
Failure to empty it will result in the cast iron grate overheating and a scarce air intake.
The ash pan must be emptied when the stove is cold.
Cleaning the glass pane
To clean the inside glass surface, we recommend using GLASSKAMIN available at your retailer EDILKAMIN.
Do not clean the glass during stove operation or while hot!
NOTE: ceramic glass withstands high temperatures, but it is fragile, so protect it from accidental blows.
Cleaning the external parts
The covering must be cleaned with a gentle detergent and damp cloth. Do not use cold water when the stove is hot since the sudden temperature change could cause damage.
Cleaning the firebox
Clean the firebox compartment regularly or, in any case, when soot deposits become excessive. This leads to better stove operation and efficiency.
Cleaning the flue
This must be done before periods of stove use and every time you notice a layer of soot and tar (easily flammable substances) on the inside of the duct. When deposits reach
a thickness of 5 – 6 mm, high temperatures, and sparks may set them on fire with serious consequences for both the flue and your home.

TROUBLESHOOTING

Most of the times apparent inconveniences are caused by distractions or a non- workmanlike installation. However, below is shown what to do in the most frequent cases.

1. In case of smoke emissions, make sure that:
   The smoke valve is open enough.
   The air inlet adjustment lever is open enough.
   The installation has been carried out correctly (smoke duct, flue, chimney pot).
   The wood is dry.

2. In case of uncontrolled combustion, make sure that:
   The smoke valve is not too open
   The door seals are in place.
   The firebox door is tightly closed.

3. In case the glass gets easily dirty, make sure that: The wood is dry.
   The smoke valve is always open at least by 25-30%
   However, keep in mind that after a few hours of operation, it is normal that a slight layer of dust deposits on the glass.

4. In the event the inconvenience cannot be solved, please contact your dealer.

SUITABLE CLEANING ACCESSORIES

| GlassKamin
(code 155240)
For cleaning ceramic glass.
---|---
| Ash vacuum cleaner without motor
(code 275400)
For cleaning the firebox.

DELUXE – DIAMOND

|
---|---
No| | Pz.|
---|---|---|---
1| Ash grate| 1| 664860
2| Hearth| 1| 664870
3| Baffle| 1| 664880
4| Ash pan| 1| 664890
5| Door with glass DELUXE| 1| 664900
5| Door with glass DIAMOND| 1| 667220
6| Ceramic glass DELUXE| 1| 664910
6| Ceramic glass DIAMOND| 1| 667230
7| Door blocking spring| 1| 664920
8| Steel side right / left| 2| 664930
9| Handle| 1| 664940
–| Screw kit DELUXE/DIAMOND| 1| 664950
–| Gasket kit DELUXE| 1| 664960
–| Gasket kit DIAMOND| 1| 667250

DELUXE – DIAMOND
www.edilkamin.com
659690 …..10.12/E

References

• Caminetti stufe a pellet e legna EDILKAMIN, termocamini termostufe caldaie pellet

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>