MEIG SNM500 Wireless Communication Module Instruction Manual
- June 2, 2024
- MEIG
Table of Contents
MEIG SNM500 Wireless Communication Module Instruction Manual
INSTALLATION INSTRUCTION
SNM500 adopts Qualcomm QCM2150 platform, 4-core A53(4* 1.3GHz) with 28nm FinFET process, 64bit ARM. It supports decode/encode up to 1080P@30fps, H.264, HD+ screen resolution, and dual ISP cameras. SNM500 is equipped with Android 10 operating system and a board memory of 1GB+8GB (2GB+16GB, and 3GB+32GB).
SNM500 can provide functions such as voice, SMS, address book, 2.4G/5G WiFi, BT. It supports dual 800W 3D camera or the depth-of-field camera, which can be widely used in intelligent POS cash registers, logistics terminals, VR Camera, intelligent robots, video recorder, security, automotive equipment, intelligent information collection equipment, intelligent handheld terminals, UAV and other products.
Main Advantage
- Support main screen display HD+ (1440×720)@60pfs
- Support Dual ISP, Dual Camera (8M+8M) 13MP camera
- Integrate multi-constellation GNSS receivers, fast and accurate positioning in different environments
- Support 1080P @30fps video en/decoding
Qualcomm
4*A53@1.3G Hz
Adreno™Adreno 308
Android 10
BT 4.2
(BR/DDR+BLEa
IEEE 802 11
a/b/g/n/ac
H.264,
HEVC,VP8
LGA+LCC
Audio & Video
Support VoLTE Ultra HD voice calls SRVCC/
CSFB voice fallback technology
24-bit/192kHz High fidelity music playback
Video codec: 1080P @30fps
WiFi video codec: 1080P @30fps
Display Interface
4-lane MIPI_DSI HD+(1440 x 720)@60fps
Camera Interface
Main camera: 4-lane MIPI CSI
Auxillary camera: 2-lane MIPI_CSI
Max rate: 2.1Gbps/lane, support 13M pixells
Touch Screen Interface
- Capacitive touch screen
Audio Interface
- Analog output: speaker, earpieces, earphone
- Analog input: 3xmicrophone, 1 x noise reduction microphone
Other Interface
USB : USB 2.0*1, support USB OTG
12C: x5
(U)SIM : x2 (1.8V/2.95V)
UART: x3 (support HW flow control, MAX 4Mbps)
SD card : x1 (SD 3.0, 4-bit SDIO)
PWRKEY: 1.8V, Internal pull-up
SPI : x5
ADC: x2
GPIO : 24
Motor drive: x1
LED: x1
Antenna: WiFi & BT antenna
Outstanding Interface
WLAN: 2.4G/5G, 802.11 a/b/g/n/ac
BT : BT2.1+EDR/3.0/4.1 LE/4.2 BLE
Built-in charge IC and gauge meter
Support DSDS
Firmware update via USB
General Feature
OS : Android 10.
Storage :
8GB eMMC 1GB LPDDR3 (default)
16GB eMMC+2GB LPDDR3 (optional) Operating
Temperature: -30°C~+75°C
Storage Temperature: -40°C~+85°C Size: 40.5mm x 40.5mmx2.8mm
Package: LCC+LGA
Weight: 13.0g
Regulatory Compliance Statement
FCC Statement:
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
IC Statement:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Operational use conditions
Module has professional users use condition limitations, Host product
manufacturer please ensure giving such warning like “Product is limited to
professional users use” in your product’s instruction.
Labelling Instruction for Host Product Integrator
Please notice that if the FCC and IC identification number is not visible when
the module is installed inside another device, then the outside of the device
into which the module is installed must also display a label referring to the
enclosed module. For FCC, this exterior label should follow “Contains FCC ID:
2APJ4-SNM500”. In accordance with FCC KDB guidance 784748 Labeling Guidelines.
For IC, this exterior label can use wording “Contains IC: 23860-SNM500”. §
15.19 and RSS-Gen Labelling requirements shall be complied on end user device.
Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and
relevant KDB publications. For E-label, please refer to §2.935.
Installation Notice to Host Product Manufacturer
7KH2(0LQWHJUDWRULVUHVSRQVLEOHIRUHQVXULQJWKDWWKHHQGXVHUKDVQRPDQXDOLQVWUXFWLRQWRUHPRYHRULQVWDOO
PRGXOH 7KHPRGXOHLVOLPLWHGWRLQVWDOODWLRQLQPRELOHDSSOLFDWLRQDVHSDUDWHDSSURYDOLV
required for all other operating configurations, including portable
configurations with respect to §2.1093 and difference antenna configurations.
Antenna Change Notice to Host manufacturer
If you desire to increase antenna gain and either change antenna type or use
same antenna type certified, a Class II permissive change application is
required to be filed by us, or you (host manufacturer) can take responsibility
through the change in FCC ID and IC ID (new application) procedure followed by
a Class II permissive change application.
FCC other Parts, Part 15B Compliance Requirements for Host product
manufacturer
This modular transmitter is only FCC authorized for the specific rule parts
listed on our grant, host product manufacturer is responsible for compliance
to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. Host manufacturer in any case shall ensure
host product which is installed and operating with the module is in compliant
with Part 15B requirements. Please note that For a Class B or Class A digital
device or peripheral, the instructions furnished the user manual of the end-
user product shall include statement set out in §15.105 Information to the
user or such similar statement and place it in a prominent location in the
text of host product manual. Original texts as following:
For Class B
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For Class A
Note: This equipment has been tested and found to comply with the limits
for a Class digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>