Cobra 036I400PSW Pure Sine 400w Power Inverter User Guide

036I400PSW Pure Sine 400w Power Inverter

“`html

Product Specifications:

• Model: Pure Sine 400W Power Inverter

• Power Output: 400W

• Waveform: Pure Sine Wave

• Input Voltage: 12V DC

• Output Voltage: 120V AC

• USB Ports: USB-A Fast Charge port (5V/9V/15W), USB-C Fast
  Charge port (5V/9V/15W)

• AC Outlets: (2) GFCI Protected AC Outlets

Product Usage Instructions:

Connecting Directly To A Vehicle Battery:

1. Mount the inverter inside the vehicle in a well-ventilated
   location close to the battery.

2. Disconnect the NEGATIVE (-) or black battery terminal of the
   vehicle.

3. Route cables close to the battery.

4. Install the insulated terminal boots on the inverter end of the
   power cables (RED = positive, BLACK = negative).

5. Connect the BLACK Cable to the Negative(-) terminal on the
   Inverter.

6. Connect the RED Cable to the Positive (+) terminal on the
   Inverter.

7. Connect the other end of the RED cable to the (+) terminal on
   the vehicle battery.

8. Visually inspect and make sure the red wire or its connectors
   are not touching any metal parts of the vehicle or the black wire
   connectors.

9. Connect the other end of the BLACK cable to the (-) terminal on
   the vehicle battery. Caution: There is normally a spark at the
   point of contact at the negative terminal.

10. Check all connections making sure the RED cable is connected to
    the POSITIVE (+) terminals and the BLACK cable is connected to the
    NEGATIVE (-) terminals.

11. Press the POWER button to turn on your inverter.

Connecting To A Vehicle Accessory Port:

1. Mount your inverter in a well-ventilated area of the
   vehicle.

2. Remove the thumb cap on the inverter for each terminal.

3. Connect the RED (+) 12V Accessory Cable ring terminal to the
   RED(+) inverter terminal.

4. Screw the thumb cap back on the RED (+) inverter terminal.

5. Connect the BLACK (-) 12V Accessory Cable ring terminal to the
   BLACK (-) inverter terminal.

6. Screw the thumb cap back on the BLACK(-) inverter
   terminal.

7. Plug the 12V Accessory Cable into a vehicle accessory
   port.

8. Place the power switch into the ON position by pressing the
   left side of the switch to turn ON your inverter. Place the power
   switch into the OFF position by pressing the right side of the
   switch to turn OFF your inverter.

Frequently Asked Questions (FAQ):

Q: What is the maximum load supported by the 12V Accessory

Cable and how do I prevent overload?

A: The 12V Accessory Cable can support on average up to 120
Watts. To prevent overload, please refer to your vehicle manual for
the maximum load your vehicle’s accessory port can handle.

“`

Cobra®
PURE SINE 400W
POWER INVERTER
(Sold Separately)
QUICK START GUIDE

Connecting Directly To A Vehicle Battery
(Please Refer to Diagram on Previous Page)
1. Mount the inverter inside the vehicle in a well ventilated location close to the battery
2. Disconnect the NEGATIVE (-) or black battery terminal of the vehicle
3. Route cables close to the battery
4. Install the insulated terminal boots on the inverter end of the power cables (RED = positive, BLACK = negative)
5. Connect the BLACK Cable to the Negative(-) terminal on the Inverter
6. Connect the RED Cable to the Positive (+) terminal on the Inverter
7. Connect the other end of the RED cable to the (+) terminal on the vehicle battery
8. Visually inspect and make sure the red wire or its connectors are not touching any metal parts of the vehicle or the black wire connectors
9. Connect the other end of the BLACK cable to the(-) terminal on the vehicle battery. Caution: There is normally a spark at the point of contact at the negative terminal
10. Check all connections making sure the RED cable is connected to the POSITIVE (+) terminals and the BLACK cable is connected to the NEGATIVE (-) terminals
11. Press the POWER button to turn on your inverter

Connecting To A Vehicle Accessory Port

Connect the BLACK 12V Accessory Cable to the Negative Post on the Power Inverter

Connect the RED 12V Accessory Cable to the Positive Post on the Power Inverter

A
Be sure the cables are correctly connected

–
·Plug the 12V Accessory Cable
into the Vehicle Accessory Port*

1. Mount your inverter in a well-ventilated area of vehicle
2. Remove the thumb cap on the inverter for each terminal
3. Connect the RED (+) 12V Accessory Cable ring terminal to the RED(+) inverter terminal.
4. Screw the thumb cap back on the RED (+) inverter terminal
5. Connect the BLACK (-) 12V Accessory Cable ring terminal to the BLACK (-) inverter terminal.
6. Screw the thumb cap back on the BLACK(-) inverter terminal
7. Plug the 12V Accessory Cable into vehicle accessory port
8. Place the power switch into the ON position by pressing the left side of the switch to turn ON your inverter. Place the power switch into the OFF position by pressing the right side of the switch to turn OFF your inverter
The 12V Accessory Cable can support on average up to 120 Watts. Do not overload . Please refer to your vehicle manual for the maximum load your vehicle’s accessory port can handle

PURE SINE 400W Features

+ @
0

[Q]

A. Negative Power Input Terminal
B. Cooling Fan – regulate the temperature of the inverter, turning on when temperature exceeds the preset limit, and turning off
when the temperature reduces
C. Positive Power Input Terminal
D. USB-A Fast Charge port (5V/9V/15W)
E. Power/Fault LED Indicator
F. USB-C Fast Charge port (5V/9V/15W)
G. Port for Cobra Remote On/Off Controller with Fast Charge USB (Sold Separately)
H. (2) GFCI Protected AC Outlets
I. Power Switch
J. Power Cables
K. 12 Volt Accessory Cable (for vehicle accessory port) L. Cobra Remote On/Off Controller with
Fast Charge USB (Sold Separately)

·

. iJ *Model CPIALCDG 1

I

Connecting Directly To A Vehicle Battery
(Instruction on the Following Page)

Connect the BLACK Cable to the Negative Post on the Power Inverter
–

+ @
0

Connect the RED Cable to the Positive Post on the Power Inverter

Connect the Negative and Positive Cables to
the Negative and Positive Terminals on the Vehicle Battery
A
Be sure the cables are correctly connected

L~J

–

To Vehicle
· i Electrical System

To Vehicle
i ·Electrical System Continued )

Thank you for purchasing the Cobra PURE SINE 400 Watt Inverter (Model CPl400PSW)
Ideal for travelers and outdoor enthusiasts who want to power devices and equipment as if they were home. Also perfect for specialty and medical equipment. Count on Cobra for Power Where You Need It.
Download the full CPl400PSW manual at:
cobra.com/manuals
Cobra® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics CorporationTM is a trademark of Cobra Electronics Corporation, USA. Other trademarks and trade names are those of their respective owners.
©2020 Cobra Electronics Corporation

1|Page
©2020 Cobra Electronics Corporation

Version A

Table of Contents
Table of Contents ……………………………………………………………………………………………………. 2 INTRODUCTION ………………………………………………………………………………………………………. 3 HOW YOUR POWER INVERTER WORKS……………………………………………………………………….. 3 WHAT’S IN THE BOX ………………………………………………………………………………………………… 3 OPTIONAL ACCESSORIES…………………………………………………………………………………………… 3 CONTROLS AND CONNECTIONS …………………………………………………………………………………. 4 IMPORTANT PRODUCT/SAFETY INFORMATION ……………………………………………………………. 6 PENTAGON PROTECTION®………………………………………………………………………………………… 7 GETTING STARTED…………………………………………………………………………………………………… 8 POWER CONSUMPTION …………………………………………………………………………………………… 8 MOUNTING THE INVERTER ……………………………………………………………………………………….. 9 PURE SINE 400W INSTALLATION………………………………………………………………………………..10 CONNECTING TO THE BATTERY………………………………………………………………………………….11 PURE SINE 400W 12V ACCESSORY INSTALLATION …………………………………………………………12 CONNECTING TO THE 12V ACCESSORY………………………………………………………………………..13 TURNING YOUR INVERTER ON AND OFF ……………………………………………………………………..15 COBRA REMOTE ON/OFF CONTROLLER WITH FAST CHARGE USB ……………………………………15 OPERATING INDICATORS ………………………………………………………………………………………….16 OPERATING LIMITS………………………………………………………………………………………………….16 TROUBLESHOOTING ………………………………………………………………………………………………..17 SPECIFICATIONS ……………………………………………………………………………………………………..18 WARRANTY & TRADEMARK ACKNOWLEDGEMENT……………………………………………………….19 MAINTENANCE & PRODUCT SERVICE………………………………………………………………………….20
2|Page

INTRODUCTION
Thank you for purchasing the Cobra PURE SINE 400W Power Inverter (Model CPI400PSW). Your inverter is designed with “Pure Sine Wave,” a wave form identical to AC power you use inside your home. Rely on Pure Sine Wave to operate your sensitive electronics such as medical equipment (i.e. CPAP or nebulizer), audio/video systems, programmable appliances, computers, communications equipment, and appliances designed with an inductive motor properly and more efficiently. Your appliances will “thank you” for it. Use this inverter to power AC appliances inside your vehicle. The inverter is designed to power continuously from a 12 Volt DC source (i.e. vehicle battery). Used properly, this Cobra product will give you reliable power to run your appliances and devices. Please read this manual thoroughly before you install and set up your new power inverter.
HOW YOUR POWER INVERTER WORKS
The Cobra PURE SINE 400W Power Inverter is a power conversion device that is designed and built to operate from low Voltage DC (Direct Current) power from your vehicle battery and converts it to standard 115 Volt AC (Alternating Current) power like you have in your home. This conversion process allows you to use many of your household appliances and electronic products in automobiles, RVs, boats, trucks and virtually anywhere else with a 12 Volt battery.
PRODUCT SERVICE AND SUPPORT
For any questions about operating or installing this new Cobra product, PLEASE CONTACT COBRA FIRST…do not return this product to the retail store. The contact information for Cobra will vary depending on the country in which you purchased and utilize the product. For the latest contact information, please go to www.cobra.com/support or call 1-800-543-1608.
If your product should require factory service, please go to www.cobra.com/support and follow the instructions.
WHAT’S IN THE BOX
· Cobra CPI400PSW Power Inverter · 16″ #12 AWG Power Cables · 16″ 12-Volt Accessory Cable · Quick Start Guide
OPTIONAL ACCESSORIES ­ available at www.cobra.com
· CPIALCDG1 – Remote On/Off controller with Fast Charge USB
3|Page

CONTROLS AND CONNECTIONS
4|Page

A. Negative Power Input Terminal B. Cooling Fans ­ regulate the temperature of the inverter, turning on when
temperature exceeds the preset limit, and turning off when the temperature reduces C. Positive Power Input Terminal D. USB-A Fast Charge port (5V/9V/15W) E. Power/Fault LED Indicator F. USB-C Fast Charge port (5V/9V/15W) G. Port for Cobra Remote On/Off Controller with Fast Charge USB (Sold Separately) H. (2) GFCI Protected AC Outlets I. Power Switch J. Power Cables K. 12 Volt Accessory Cable (for vehicle accessory port) L Cobra Remote On/Off Controller with Fast Charge USB (Sold Separately)
** = Fast Charge works only on devices capable of supporting a charge up to 10W
5|Page

IMPORTANT PRODUCT /SAFETY INFORMATION
Before installing and using your Cobra power inverter, please read these general precautions and warnings. Caution and Warning Statements Special attention must be paid to the CAUTION and WARNING statements in the manual. CAUTION: Statements specify conditions which could cause damage to the unit or other equipment. WARNING: Statements identify conditions that could result in personal injury or loss of life. General Precautions 1. Never install the inverter in a boat’s engine compartment where gas and battery fumes are
present. 2. Do not operate the inverter if it has been dropped or damaged in any way. 3. Do not open the inverter; it contains no user-serviceable parts. Attempting to service unit could
cause electrical shock. NOTE: Internal components remain charged after all power is disconnected. 3. Do not expose the inverter to rain, snow, bilge water or spray. 4. Do not obstruct the ventilation openings. 5. Do not install the inverter in zero-clearance compartment. 6. Do not allow water or liquids in contact with the power inverter 7. Do not use appliances with damaged or wet cords.
CAUTION: This inverter should be used in negative ground applications only.
CAUTION: The inverter must only be connected to batteries with a nominal output voltage of 12 volts. Do not connect the power inverter to a 6 Volt battery and will be damaged if connected to a 24 Volt battery.
WARNING: Power inverters contain components that tend to produce arcs or sparks. To prevent fire or explosion, do not install the inverter in areas or compartments containing batteries or flammable materials or in locations that require ignition-protected equipment.
WARNING: To avoid fire, do not cover or obstruct the ventilation openings. Do not install the power inverter in a tight space or closed compartment where airflow may be restricted.
Proposition 65: Warning: Wash Hands After Handling Power Cord The power cord on this product contains lead, a chemical known in the state of California to cause birth defects or other reproductive harm.
6|Page

Caution: Rechargeable Appliances Certain chargers for small nickel cadmium batteries can be damaged if connected to a Cobra POWER 400PSW inverter. Two particular types of equipment are prone to this problem: 1. Small battery- operated appliances such as flashlights, razors, and night lights that can be plugged directly into an AC receptacle to recharge. 2. Certain battery chargers for battery packs used in hand power tools. These chargers have a WARNING label stating that dangerous voltages are present at the battery terminals.
This problem does not occur with the vast majority of battery operated equipment. Most use a separate charger or transformer that is plugged into the AC receptacle and produces a low voltage output. If the label on the AC adapter or charger states that it produces a low voltage AC or DC output (less than 30 volts), the inverter will have no problem powering the adapter safely.
PENTAGON PROTECTION®
Cobra power inverters provide five levels of protection: 1. Over-Temperature: Auto-shut off will occur when the safe operating temperature has been exceeded. 2. Reverse Polarity: The inverter will not operate if connected incorrectly to the power source. 3. Over-Voltage: Auto-shutdown will occur if the DC input exceeds safe operating levels. 4. Low Voltage Alarm: The inverter will sound an alarm to indicate a low battery voltage condition. 5. Low Voltage Cutoff: The inverter will automatically shut off to prevent a dead battery condition.
For detailed specifications go to Specifications section of this manual, starting on page 18.
7|Page

GETTING STARTED
This section provides you with the basic information about the inverter and a few tips before installation. To get started, you will need: 1. A 12 Volt DC battery (i.e. vehicle battery. In order to understand how much current your battery must
deliver, divide the number of Watts from your AC appliance or device by 10. 2. Cables to connect your inverter to the vehicle battery. These come with your PURE SINE 400W
Inverter and provide a length of 16″. If you need to install the inverter permanently, longer cable is required with a larger gauge. DETERMINING THE POWER REQUIREMENTS FOR YOUR PRO INVERTER Before you turn on your power inverter and plug in an appliance or device, you will want to understand its power requirements. To determine the requirements, you will need to know the Watts of your device. This can be calculated by multiplying the Amps by 110 Volts (See Below).
POWER CONSUMPTION
For each piece of equipment you will be operating from the power inverter, you must determine the battery’s reserve capacity (how long the battery can deliver a specific amount of current ­ in automotive batteries, usually 25 ampere) or ampere-hour capacity (a measure of how many amperes a battery can deliver for a specified length of time). Example ­ Ampere-hour capacity: a battery with an ampere-hour capacity of 100 ampere-hours can deliver 5 ampere for 20 hours before it is completely discharged. To determine the battery Ampere-hour capacity you require: 1. Determine how many Watts each piece of equipment consumes. This can normally be found on the
product label. If only the Amperage is provided, then multiply the Amps by 115 to determine the power in Watts. 2. Estimate how long you need your appliance to run. 3. Now calculate the Amp-hour rating for the battery. You can do this by multiplying the total AC load (in Watts) by the length of time (in Hours) needed to run your appliance. This will give you the Watt-Hours needed.
4. Divide the watt-hours by 10 to determine how many battery (12 volt) ampere-hours will be consumed.
8|Page

Multiply: AC AMPS X 110 (AC Voltage) = WATTS. This formula yields a close approximation of the continuous load of your appliance. Multiply: WATTS X 2 = Starting load for most appliances, tools and devices. This formula yields a close approximation of the starting load for most appliances. Exceptions are motorized appliances such as pumps, freezers, and air conditioners. These appliances can have startup loads of up to eight times the rated Watts. Determining the DC Power Requirements Your power inverter requires the input of a 12-Volt battery. To calculate the approximate power in Amps as 12-Volt battery bank you need to know the current, or Amps required for powering the continuous AC load. A shortcut method is to divide the continuous AC load Wattage by 10. For example, the continuous AC load is 400 Watts. The current (Amps) is: 400/10 or 40 Amps at 12VDC. Add to the load any DC appliances that may be powered by the battery bank.
MOUNTING THE INVERTER
Do not mount the power inverter under the hood of any vehicle. Choose a cool, dry, and well-ventilated area inside the vehicle as close to the battery as possible. Place the power inverter on a flat, secure surface. Make sure there are no wires, fuel lines or fluid tanks directly behind the wall or surface being drilled. When mounting, secure the power inverter in place using corrosion-resistant mounting hardware (not included). What you will need:
· Assess your mounting needs depending
on the inverter and type of surface you are mounting (i.e. wood or fiber glass)
· Gather the necessary tools depending
on the surface (i.e. drill or screwdriver)
· Determine size of mounting hardware.
Use only corrosive resistant screws (not included) Mounting Instructions: 1. Make sure the inverter is OFF. 2. Check for wires, fuel lines or fluid tanks behind the wall or surface you plan to drill. 3. Position the power inverter horizontally when choosing the mounting location. If mounted on a wall
be sure the front of the inverter is facing out. Do not mount vertically to prevent debris or dust from falling into the power inverter.
4. Mark the locations of the mounting screws before drilling. 5. Remove the inverter and drill the (4) mounting holes. 6. Fasten the inverter to the mounting surface using corrosion-resistant screws (not included).
9|Page

PURE SINE 400W INSTALLATION
10 | P a g e

CONNECTING TO THE BATTERY
1. Mount the inverter inside the vehicle in a well ventilated location close to the battery.
2. Disconnect the NEGATIVE (-) or black battery terminal of the vehicle.
3. Route cables close to the battery.
4. Install the insulated terminal boots on the inverter end of the power cables (RED = positive, BLACK = negative).
5. Connect the BLACK Cable to the Negative (-) terminal on the inverter.
6. Connect the RED Cable to the Positive (+) terminal on the inverter.
7. Connect the other end of the RED cable to the (+) terminal on the vehicle battery.
8. Visually inspect and make sure the red wire or its connectors are not touching any metal parts of the vehicle or the black wire connectors.
9. Connect the other end of the BLACK cable to the (-) terminal on the vehicle battery. Caution: There is normally a spark at the point of contact at the negative terminal.
10. Check all connections making sure the RED cable is connected to the POSITIVE (+) terminals and the BLACK cable is connected to the NEGATIVE (-) terminals.
11. Press the POWER button to turn on your inverter.
12. If you purchased the Cobra Remote On/Off Remote Controller with Fast Charge USB (Model CPIALCDG1) accessory, plug the controller into the RJ45 jack labeled “REMOTE”.
11 | P a g e

PURE SINE 400W 12V ACCESSORY INSTALLATION
12 | P a g e

CONNECTING TO THE 12V ACCESSORY
1. Mount your inverter in a well-ventilated area of vehicle. 2. Remove the thumb cap on the inverter for each terminal. 3. Connect the RED (+) 12V Accessory Cable ring to the RED (+)
inverter terminal. 4. Screw the thumb cap back on the RED (+) inverter terminal. 5. Connect the BLACK (-) 12V Accessory Cable ring to the BLACK (-)
inverter terminal. 6. Screw the thumb cap back on the BLACK (-) inverter terminal. 7. Make sure the inverter is in the OFF position “O”. 8. Plug the 12V Accessory Cable into vehicle accessory port*. 9. When turning your inverter ON, place the power switch into the ON or “-”
position by pressing the left side of the switch. When turning your inverter OFF, place the power switch into the OFF or “O” position by pressing the right side of the Power Switch.
13 | P a g e

CAUTION: Do not connect the inverter and another AC source (such as a generator or utility power) to the AC wiring at the same time. The inverter will be damaged if its output is connected to AC voltage from another source. Damage can even occur if the inverter is switched off.
CAUTION: Do not connect the inverter to a load greater than 400 Watts.
CAUTION: It is not recommended to operate loads at the maximum rated output for permanent or extended periods of time. For continuous operation (greater than 60 minutes), it is recommended to operate a load 20% less than the inverter maximum output rating. For example, for a 400 Watt inverter, a maximum load of 320 Watts is recommended.
CAUTION: Loose connectors result in excessive voltage drop and may cause over heated wires and melted insulation.
CAUTION: Reverse polarity connections (positive to negative) will blow internal fuses in the inverter and may permanently damage the unit. Such damage is not covered by the warranty.
CAUTION We recommend a main fuse in the battery’s positive cable to protect against DC wiring short circuits (external to the inverter). The fuse should be as close to the battery as possible. We recommend a 50 Amp ANL fuse or equivalent. The specific fuse ampere rating should be sized to allow operation of all your DC powered equipment.
CAUTION: Remove any jewelry (watch, ring, etc.). Be careful not to short circuit the battery with any metallic object (wrench, etc.).
CAUTION: Electrical installations must meet local and national wiring codes, and should be performed by a qualified electrician.
WARNING: If you are making a permanent AC connection to the inverter, make sure that the AC wiring steps are performed before any DC wiring is done. (DC hook-up energizes internal components, regardless of the position of the On/Off Switch). Working on AC connections in such a circumstance may result in an electric shock.
WARNING: 115 volt AC power is potentially lethal. Do not work on AC wiring when it is connected to the inverter (even if it is switched off) unless the DC power source is physically disconnected from the inverter. Also, do not work on AC wiring if it is connected to another AC power source such as a generator or the utility line.
WARNING: You may observe a spark when making the connection because current can flow to charge the capacitors in the inverter. Do not make this connection in the presence of flammable fumes. Explosion or fire may result. Thoroughly ventilate the battery compartment before making this connection.
14 | P a g e

TURNING YOUR POWER INVERTER ON AND OFF
Be sure to have your power inverter properly installed before attempting to turn the unit on (see installation beginning on page 10) To turn the power inverter on: 1. If a DC power supply is being used as the power source, switch it on. 2. On the Output End, press the Power Button to on.
The power inverter is now ready to deliver AC power to your loads. If several loads are to be operated by the inverter, turn them on separately, after the inverter has been turned on. This will ensure that the inverter does not have to deliver the starting currents required for all the loads at once.
NOTE: The Power Button turns the control circuit in the inverter on and off. It does not disconnect power from the inverter. When the button is in the off position, the inverter draws no current from the battery. When it’s in the on position, but no power is being supplied to a load, the inverter draws less than 600 milliamperes from the battery. This is low current draw. It would take more than a week to discharge a 100 ampere-hour battery at this rate depending on the age of the battery.
COBRA REMOTE ON/OFF CONTROLLER WITH FAST CHARGE USB
Your Cobra POWER inverter is equipped with an RJ-45 jack labeled “REMOTE” for compatibility with the Cobra Remote On/Off Controller with Fast Charge USB to allow you to conveniently turn the inverter ON and OFF from anywhere inside your vehicle as well fast charge your devices at the same time. Perfect for use while driving, traveling, camping or tailgating when your inverter is out of reach. (4) mounting options allow you to install it permanently, use it while driving in a cup holder or clip it to the back of a seat or a place inside your vehicle.
Sold Separately. Can be purchased on www.Cobra.com
15 | P a g e

OPERATING INDICATORS
Indicators on the power inverter show the unit’s power status and alarms for conditions that could cause it to shut down. The power and protection indicator includes a dual color green and red light, and an alarm. Green Light Power on ­ The green light should remain on steady.
Red Light and/or Alarm Current overload ­ The red light will blink continuously, then the inverter will shutdown. The inverter will continue to check for appropriate current levels while trying to restart the load.
DC input voltage overload ­ The red light will turn on and the inverter will shutdown. The inverter will continue to check for appropriate voltage levels while trying to restart the load.
DC input voltage shortage ­ As a warning that the voltage is getting low, the internal alarm will sound. When the voltage is too low, the inverter will shutdown and the light will turn red. The inverter will continue to check for appropriate voltage levels while trying to restart the load.
Temperature overload ­ The red light will blink, then the inverter will shutdown. The inverter will continue to check for appropriate temperature levels while trying to restart the load.
NOTE: A momentary sound of the internal alarm and/or flash of the red light is normal at start up.
OPERATING LIMITS
Power Output The inverter can deliver 400 watts for about 60 minutes. The inverter must cool for 15 minutes before it can resume operation at 400 watts. Note: The wattage rating applies to resistive loads. The inverter will operate most AC loads within its power rating. Some induction motors used in freezers, pumps, and other motor-operated equipment require very high surge currents to start. The inverter may not be able to start some of these motors even though their rated current draw is within the inverter’s limits. The inverter will normally start single phase induction motors rated at one-half HP or less.
Input Voltage The inverter will operate from input voltage ranging from 10 volts to 15 volts. Optimum performance will occur when the voltage is between 12 volts and 14 volts. If the voltage drops below 10.5V+/-0.3V, an audible low battery warning will sound. The inverter will shut down if the input voltage drops below 9.5V+/-0.3V. This protects the battery from being over-discharged. It will restart when the input voltage exceeds 12V+/-0.3V. The inverter will also shut down if the input voltage exceeds change to 15.5V+/-0.5V. This protects the inverter against excessive input voltage. Although the inverter has protection against over-voltage, it may still be damaged if the input voltage were to exceed 16 volts.
16 | P a g e

TROUBLESHOOTING GUIDE

Problem/Symptom Low output voltage No output voltage No output voltage aer prolonged use
No output voltage, “Protect” indicator lighted
No output voltage No output voltage
Low baery alarm on all the me

Possible Causes Overload Low input voltage Thermal shutdown
High input voltage
Short circuit Inverter switched off No power to inverter Reverse DC polarity Poor DC wiring Poor baery condion

on
Reduce the load.
Recharge baery. Check connecons and cable.
Allow inverter to cool o.
Reduce load, connuous operaon input current required.
Improve venlaon; make sure venlaon openings in the inverter are not obstructed.
Reduce ambient temperature.
Make sure the inverter is connected to 12V baery.
Check regulaon or charging system.
Check load for proper operaon.
Turn inverter on.
Check wiring to inverter.
Observe correct polarity.
Check connecons.
Make sure baery is fully charged.

17 | P a g e

SPECIFICATIONS

Specifications: Model Input Output Output Waveform Continuous Power Peak Power Efficiency No Load Draw
Low Battery Alarm

PURE SINE 400W CPI400PSW 13.0V DC
115V AC, 60Hz, 3.4A, 400W Pure Sine Wave (PSW) 400 Watt 800 Watt 90% < .6A
10.5V DC

Low Battery Shutdown USB-A Output Port USB-C Output Port AC Output Socket
Protection
Operating Temperature Storage Temperature Power Cable Length: CLA Cable Length:
Compatible with Cobra Remote LCD (SKU CPIALCDG1)

9.5V DC 5V/3.0A, 9V/1.67A Fast Charge 5V/3.0A, 9V/1.67A Fast Charge 2 GFCI Protected AC Outputs
Overload, Over Temperature, Short Circuit, Reverse Polarity, Over/Under Voltage and GFCI
-10°C/14°F – 40°C/104°F -40°C/-40°F – 65°C/149°F 16″ #12 AWG (1) Red, (1) Black
16″
Yes

Specifications subject to change without notice. Please go to www.Cobra.com for more details

18 | P a g e

WARRANTY & TRADEMARK ACKNOWLEDGEMENT
Limited Two-Year Warranty For Products Purchased in the U.S.A. Cobra Electronics Corporation warrants that its Cobra power inverter, and the component parts thereof, will be free of defects in workmanship and materials for a period of two years from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A. Cobra will, without charge, repair or replace, at its option, defective power inverters, products or component parts upon delivery to the Cobra Factory Service department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt. You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra’s expense, if the product is repaired or replaced under warranty. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Exclusions: This limited warranty does not apply: 1. To any product damaged by accident. 2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs. 3. If the serial number has been altered, defaced, or removed. 4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty. Cobra shall not be liable for any incidental, consequential or other damages; including, without limitation, to damages resulting from loss of use or cost of installation. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
For Products Purchased outside the U.S.A. Please contact your local dealer for warranty information.
Trademark Acknowledgement Cobra®, Nothing Comes Close to a Cobra®, Pentagon Protection® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics CorporationTM is a trademark of Cobra Electronics Corporation, USA.
19 | P a g e

MAINTENANCE & PRODUCT SERVICE
Maintenance Very little maintenance is required to keep the inverter operating properly. The exterior of the unit should be cleaned periodically with a damp cloth to prevent accumulation of dust and dirt. At the same time, tighten the screws on the DC input terminals. Be sure vents and fans are free of dust or debris. Product Service For any questions about operating or installing this new Cobra product, please go to www.cobra.com
20 | P a g e

PURE SINE 400W
Power Inverter

Pure Sine Power Inverter with Fast Charge USB
Ideal for travelers and outdoor enthusiasts who want to power devices and equipment as if they were home. Perfect for specialty and medical equipment. Count on Cobra for Power Where You Need It.

USB-C Port

Product Features
400 Watts Continuous Power 800 Watts Peak Power

Input/Output LED Indicator

90% Efficiency

(2) GFCI Protected AC Outlets

USB-A Port

(2) AC Outlets
USB-A Fast Charge Port
USB-C Fast Charge Port

LED Indicator
Compatible with Cobra Remote On/Off Controller with Fast Charge USB
Sold Separately

Cooling Fan

Power Button

Remote On/Off Controller Port

Pentagon Protection® Safety Rugged Industrial Design
Negative Battery Terminal

Positive Battery Terminal

*Optional Cobra Remote On/Off Controller with Fast Charge USB to monitor & charge devices from anywhere
inside your vehicle

What’s Included: · Cobra CPI400PSW
Power Inverter · 16″ #12 AWG
Direct-to-Battery Power Cables · 16″ 12 Volt Accessory Cable · Quick Start Guide
www.cobra.com

Model # CPI400PSW

PURE SINE 400W
Power Inverter

Appliance Wattage Reference Chart

vsetahritcslems.ost vehicles.

General General
Unit Dimensions Unit D5im.5e0n”siHonxs2.87″ W5.5×00″.6H5x”2D.87″ W x 0.65″ D (139.7mm x 72.9(m13m9.x7m16m.5x1m72m.9) mm x 16.51mm)

uyrccheallrgpehoynoeu,rscmelal rptphhoonnee, ,smtabarletpthaonndeo, thaebrlet and other e devices. -bright LED. nigleorpetciohnasrg. ing options.
ietsUs.Sol.dA.in the U.S.A.

Unit Weight (Lbs.U) nit W9e.i2ghotz(.L(b2s6.0) .8g.)9.2 oz. (260.8g.)

Individual Box Individ1u0a.l2B5o”xH x 7.25″1W0.2×52″.2H5x”7D.25″ W x 2.25″ D Dimensions Dimen(s2i6o0n.s35mm x 184(2.1650m.3m5mxm57x.158m4.m15)mm x 57.15mm)

Individual Box WeInigdhivtid1u.a2l5Blobxs.W(5ei6g7htg.1) .25 lbs. (567 g.)

Battery

BatterLyithium-cobalt Lithium-cobalt

Battery Capacity Batter2y2C.a2pWahcity 22.2Wh

35 W USB Output USB O2u.t4pAut

2.4A

Start Current Start C1u8r0reAnt

180A

Peak Current Peak C3u6r0reAnt

360A

Model

ModelCPP8000 CPP8000

Master Pack Qty.Maste6r Pack Qty. 6

Master Pack Maste1r 2P.a4c0k” H x15.551″2W.4×0″7.H68x1″5D.55″ W x 7.68″ D
30-60 W Dimensions Dimen(s3i1o5nms m x 395mm(31x51m9m5mxm3)95mm x 195mm)
Master Pack WeiMghatste8r .P5alcbks.W(3e.ig8h5tkg.8).5 lbs. (3.85 kg.)

UPC #

UPC #0 28377 31382 00 28377 31382 0

Master Pack BarcMoadsete2r P0a0ck28B3a7rc7o3de13282004 28377 31382 4

60-90 W without notwicieth.out notice.

40-100 W

35-150 W

90-150 W
German GermanPortuguesPeortuguesSe panish Spanish
200 W

Continuous Power Surge Power Efficiency Rating No-load draw Output Waveform Input Voltage Range Output Low Voltage Alarm Low Voltage Cut-Off AC Receptacles Fast Charge USB-A Output Fast Charge USB-C Output Remote-Ready Output Port Remote Included 12V Vehicle Accessory Cable Includes Direct-to- Battery Cables Direct-to-Battery Cables Thermal Shut-Down Reverse Polarity Protection Volt/Watt Meter Warranty Package Type Product Weight Product dimensions Package dimensions Master pack quantity Master pack dimensions Master pack weight UPC Master pack barcode
Sold Separately

400W 800W 90% < .6A Pure Sine Wave 10.5 – 15.0V DC 115V AC, 60Hz, 3.4A, 400W 10.5V DC 9.5V DC 2 GFCI Protected AC Outputs 5V/3.0A, 9V/1.67A Fast Charge 5V/3.0A, 9V/1.67A Fast Charge Yes No Yes Yes 16″ #12 AWG Cables Yes Yes 2-Color LED 2 Year Gift Carton 1.98 lbs 8.86″ H x 5.39″ W x 2.83″D 11.02″ W x 9.06″ H x 3.15″ D 6 10.24″ H x 11.42″ W x 18.90″ D 16.04 lbs 0 28377 31556 5 2 00 28377 31556 9

300 W

General Product Launch Info

MSRP/MAP:

$129.95

kaenddetshigensanraekeredgeisstiegrneadre registered
www.cobra.com aCEolercptororantiicosnC, UoSrApo. ration, USA.

CPP8000 5C/P1P58000 5/15

Cobra® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics CorporationTM is a trademark of Cobra Electronics Corporation, USA. Other trademarks and trade names are those of their respective owners.
Model # CPI400PSW

Important Power Inverter Safety Information
Before installing and using your Cobra power inverter, please read these general precautions and warnings. Caution and Warning Statements To make the most of this inverter, it must be installed and used properly. Please read the installation and operating instructions carefully before installing and using it.
CAUTION: Statements specify conditions which could cause damage to the unit or other equipment.
WARNING: Statements identify conditions that could result in personal injury or loss of life.
General Precautions 1. Never install the inverter in a boat’s engine compartment where gas and battery fumes
are present. 2. Do not operate the inverter if it has been dropped or damaged in any way. 3. Do not open the inverter; it contains no user-serviceable parts. Attempting to service unit could
cause electrical shock. NOTE: Internal components remain charged after all power is disconnected. 4. Do not expose the inverter to rain, snow, bilge water or spray. 5. Do not obstruct the ventilation openings. 6. Do not install the inverter in zero-clearance compartment.
CAUTION: This inverter should be used in negative ground applications only. WARNING: Power inverters contain components that tend to produce arcs or sparks.
To prevent fire or explosion, do not install the inverter in areas or compartments containing batteries or flammable materials or in locations that require ignitionprotected equipment. WARNING: To reduce the risk of fire, do not cover or obstruct the ventilation openings. Do not install inverter in zero-clearance compartment.
Proposition 65 Warning: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. Caution: Rechargeable Appliances Certain chargers for small nickel cadmium batteries can be damaged if connected to a Modified Sine Wave inverter. These chargers will operate efficiently with a Cobra Pure Sine Wave inverter. Two particular types of equipment prone to this problem: 1. Small battery-operated appliances such as flashlights, razors, and night lights that can be plugged
directly into an AC receptacle to recharge. 2. Certain battery chargers for battery packs used in hand power tools. These chargers have a
WARNING label stating that dangerous voltages are present at the battery terminals. This problem does not occur with the vast majority of battery operated equipment. Most use a separate charger or transformer that is plugged into the AC receptacle and produces a low voltage output. If the label on the AC adapter or charger states that it produces a low voltage AC or DC output (less than 30 volts), the inverter will have no problem powering the adapter safely.

Limited 2-Year Warranty
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra power inverter, and the component parts thereof, will be free of defects in workmanship and materials for a period of two years from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective power inverters, products or component parts upon delivery to the Cobra Factory Service department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra’s expense, if the product is repaired or replaced under warranty. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs.
3. If the serial number has been altered, defaced, or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty. Cobra shall not be liable for any incidental, consequential or other damages; including, without limitation, to damages resulting from loss of use or cost of installation.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
For Products Purchased Outside the U.S.A.
Please contact your local dealer for warranty information.

lnformaci6n lmportante de Seguridad del lnversor de Potencia
Lea las siguientes precauciones y advertencias antes de instalar y usar su lnversor de Potencia Cobra.
Declaraciones de Precauci6n y Advertencias lnstale y utilice adecuadamente su inversor para aprovecharlo al maxima. Lea cuidadosamente las instrucciones de instalaci6n y operaci6n antes de instalar y usar su inversor.
PRECAUCION: Las declaraciones a continuaci6n especifican las condiciones que pueden provocar dafios a la unidad u otro equipo.
ADVERTENCIA: Las declaraciones a continuaci6n especifican las condiciones que pueden resultar en lesion personal o perdida de la vida.
Precauciones generales:
1. Nunca instale el inversor en el compartimiento del motor de un barco donde haya vapores de gasolina y de la bateria.
2. No opere el inversor si se ha cafdo o dafiado de cualquier manera.
3. No abra el inversor, no contiene piezas a las que pueda dar servicio el usuario. Si intenta abrir la unidad para darle servicio puede recibir una descarga electrica.
NOTA: Los componentes internos permanecen cargados despues de desconectar la fuente de alimentaci6n.
4. No exponga el inversor a la lluvia, nieve, agua de sentina, o aspersion.
5. No obstruya las aberturas de ventilaci6n.
6. No instale el inversor en compartimientos sin espacio libre.
PRECAUCION: El inversor se debe utilizar para aplicaciones de tierra negativa solamente.
ADVERTENCIA: Los inversores de potencia contienen componentes que pueden generar arcos o chispas. Para evitar incendios o explosiones, no instale el inversor en areas o compartimientos que contenga baterias o materiales inflamables, ni en lugares que requieran el uso de equipo protegido contra incendios.
ADVERTENCIA: Para reducir el riesgo de incendio, no cubra ni obstruya las aberturas de ventilaci6n. No instale el inversor en compartimientos sin espacio libre.
Advertencia de la Propuesta 65: Cancer y dafio reproductive – www.P65Warnings.ca.gov.
Precauci6n: Electrodomesticos Recargables Ciertos cargadores de baterias pequefias de nfquel y cadmio se pueden dafiar si se conectan a un inversor de Onda Sinusoidal Modificada. Dichos cargadores funcionan eficazmente con un lnversor Cobra Pure Sine Wave. Dos tipos especfficos de equipo son propensos a dicho problema: 1. Dispositivos pequefios que funcionan con baterias, tales como linternas, afeitadoras, y luces nocturnas
que se pueden conectar directamente a un tomacorrientes de corriente alterna para su recarga. 2. Ciertos cargadores de baterias que se utilizan con herramientas electricas. Dichos cargadores cuentan
con una etiqueta de ADVERTENCIA que indica que las terminales de las baterias tienen voltajes peligrosos presentes.
Este problema no sucede en la gran mayorfa del equipo operado por baterias. La mayoria utiliza un cargador o transformador separado que se conecta al tomacorriente de corriente alterna y genera una salida de voltaje bajo. Si la etiqueta en el adaptador o cargador de corriente alterna indica que genera una salida de voltaje bajo de corriente alterna o directa (menos de 30 voltios), el inversor no tendra problema para alimentar el adaptador de manera segura.

Garantfa limitada de 2 anos
Para productos adquiridos en EE. UU. Cobra Electronics Corporation garantiza que el lnversor de Potencia Cobra, y los componentes del mismo, estaran libres de defectos de mano de obra y materiales por un periodo de dos anos a partir de la fecha de compra del primer consumidor. La presente garantfa podria aplicarse al primer comprador consumidor, siempre y cuando el producto se utilice en EE. UU.
Cobra reparara o reemplazara, sin cargo y a su propio criteria, inversores de potencia defectuosos o refacciones al recibirlas en el departamento de Servicio de fabrica de Cobra, acompanados de comprobante de compra del primer comprador de consume, tal como una copia del recibo de compra.
Usted debera pagar los cargos iniciales de envfo necesarios para embarcar el producto para su servicio bajo garantfa, sin embargo los cargos de devoluci6n seran a cargo de Cobra, si el producto se repara o reemplaza bajo garantfa. La presente garantfa le proporciona derechos especfficos legales, y tambien podrfa tener otros derechos, los cuales varfan en cada estado.
Exclusiones: La presente garantfa limitada no se aplica a lo siguiente:
1. A ningun producto danado por accidente.
2. En caso de uso indebido o abuso del producto como resultado de alteraciones o reparaciones no autorizadas.
3. Si el numero de serie ha sido alterado, desfigurado o retirado.
4. Si el propietario del producto reside fuera de EE. UU.
Todas las garantfas implicitas, incluyendo garantfas de comerciabilidad e idoneidad para un objetivo en particular son limitadas a la duraci6n de la presente garantfa. Cobra no se hara responsable de danos incidentales, consecuenciales, u otros; incluyendo, sin limitaci6n, a danos generados por perdida de uso o costo de instalaci6n.
Algunos estados no permiten limitaciones en cuanto a la duraci6n de la garantfa, y/o no permiten la exclusion o limitaci6n de danos incidentales o consecuenciales, asi que las limitaciones anteriores podrfan no aplicar a usted.
Para productos adquiridos fuera de EE. UU.
Comunfquese con su distribuidor local para informaci6n de garantfas.

Register your new Cobra product
www.cobra.com/register
Register your product today to get:

Helpful Product Tips

Exclusive Offers

Expert Advice

!,cobra®

References

• Communication Radios & Automotive Electronics | Cobra.com
• Product Registration
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>