ChunHee S600-P3 Intercoms Wireless User Manual
- June 14, 2024
- ChunHee
Table of Contents
ChunHee S600-P3 Intercoms Wireless User Manual
Radio Overview
Main features
- TX & RX Frequency range 400– 470MHz
- High and Low Power Selection
- 16 channels
- Type-C connector for charging
- 155 Privacy Codes (50 CTCSS Codes & 105 DCS codes) )
- Battery save
- Vocal tuning
- TOT (Time out timer)
- Battery low alert
- Up to 5 km range
- Battery Life: Up to 18 hours (under typical use conditions)
Charging the Battery
Using the Type-C USB Charger
The Type-C USB charger is a handy port that allows you to conveniently charge.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port. The other end of the data line is connected to the output port of the power bank or the adapter of the mobile phone.
- The blue light is charging, and the green light is fully charged.
- The battery will be fully charged within 6 hours.
Note:
- Suggest to turn OFF your radio while charging.
- Please remove the radio from the charger after fully charged later.
Operations
Please read this reference guide completely before using the radio.
Power ON/OFF & Adjust the Volume
-
Press and hold the key for 5 seconds to TURN ON/OFF the radio.
Tips: Please wait for 5 seconds to turn on the radio if you turn off the radio by accident. -
Press the Vol+ to increase the volume & press Vol- key to decrease the volume level.
Choosing a Channel
The radio has 16 channels you can use to talk to others. If you wanna
communicate with others by this radio please make sure all the radio is on the
same channel.
Set the channel: Hold the POWER key to turn on the radio, then use the CH+ or
CH- key to select a channel.
Keyboard Lock
Hold the CH+ key for 5 seconds till hear a beep sound to lock the channel.
When the channel is locked, press the CH+ and CH- keys will can’t change the
channel.
Press and hold the CH+ key again for 5 seconds and a beep will sound to
unlock.
Emergency alarm
Hold the VOL+ button to start the alarm function, then the unit (at the same
channel unit) will sound the alarm tone at the same time. Press PTT will exit
the alarm mode.
Battery low alert
When the battery power is below 3% , about every 25S voice prompts “Please
charge” continuous broadcast 10 times.
Automatically shut down after broadcast 10 times.
Transmission
VOX
The VOX feature enables hands free conversations without using PTT: just speak in the direction of the microphone and the communication will be automatically activated. The VOX sensitivity can be adjusted in 9 different levels (1…9) through the programming software (Must use our professional program cable connect the radio and PC):
Level 2 is set by default and has the lowest VOX sensitivity, 9 is the lowest one. With the programming software you can enable/disable the VOX feature and select the sensitivity levels. CPS programming path: Edit > VOX > VOX Level
Turn on the VOX
a. When the VOX function is enabled on your radio.
Talking to the MIC will automatically turn on the transmitter and send the
voice. Stop talking, the radio automatically stops transmitting and waits for
reception.
b. When you use the microphone with the headset. To use the voice control
function, the VOX gain must be adjusted, and the VOX gain must be set, so that
the radio can distinguish the sound level.
If the microphone is too sensitive, ambient noise can cause the radio to start transmitting. If the microphone is not sensitive enough, the radio cannot pick up your voice. Be sure to adjust the VOX gain level to make the call go smoothly.
Note: The radio has the function of manually turn on the VOX. Press and hold the VOL- and PTT keys to turn on the radio.
Repeat this operation to turn off the VOX function.
Chinese/English voice prompt
Through the CPS software, three state settings can be performed in Chinese,
English, and closed.
Manual adjustment:
In standby mode, on channel 15, hold CH- key and power key to turn on the
radio to switch between Chinese and English voices.
CTCSS/DCS tones
CTCSS and DCS tones are similar to access codes and enable the radio to
communicate only with the users that are tuned on the same channel and have
set the same code. For each channel, you can set up to 50 CTCSS tones and 155
DCS codes. The CTCSS/DCS tones are a sort of “access codes” and enable the
radio to communicate only with the other users set on the same frequency and
on the same CTCSS/DCS tone. Undesired signals coming from other stations set
on the same frequency but with different CTCSS/DCS tones won’t be received.
Appendix A. – Technical Specifications
NOTE: All specifications may be modified without prior notice or liability.
Appendix B. – Trouble shooting guide
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>