MEIG SLT719 4G LTE CPE Wireless Router User Guide

4G LTE CPE
Model Name: SLT719
User Guide

Legal Information
Copyright @2021. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means without the prior written consent of and its affiliates.
Reserves the right to change or modify any information or specification contained in this manual without prior notice and without any liability.

Limitation of Liability
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors), or totally lost. Shall not be liable for any loss of profits or indirect, special, incidental, or consequential damages resulting from or arising out of or in connection with using of this product, whether or not had been advised, knew, or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. 

Introduction of Router

Your router is for indoor use only and multiple devices like computers, smartphones or landline phones can be connected to the router to access the Internet, make telephone calls, and more.
Application Scenarios:
Scenario 1: mobile network service using a SIM card.

Scenario 2: Data service from Ethernet Internet connection (RJ45 Port).

Scenario 3: Data service from Ethernet and VoLTE voice using a SIM card.

Appearance

1. LAN port
2. WAN port
3. Telephone port
4. Micro-USB port
5. WPS/Reset button
6. Power Input
7. SIM card slot| 8. External antenna ports
9. SYS indicator
10. ETH indicator
11. WiFi/WPS indicator
12. 4G indicator
13. NET indicator
---|---

WPS/Reset button: Press once for WPS, press and hold for about 3 seconds for Reset.
Important: The router does not support any non-standard SIM cards.

Setup your Router

Insert a SIM card first and then connect the power adapter to the power input of the router. The router will power on and search for available mobile networks automatically. Do not insert or remove the SIM card when the router is running, as this may affect performance or damage the SIM card.

The intuitive indicators display the router’s status

Off: The device is powered off
ETH| On: LAN or WAN port is connected
Off: LAN or WAN port is disconnected
Blinking: Ethernet data transfer in process
WiFi/WPS| On: WiFi is on
Off: WiFi is off
Blinking: WPS connection in the process
4G| On: Connected to the 4G network
Off: Connected to the non-4G network.
NET| On: Register to network
Off: Not register to the network
Blinking: Mobile data transfer in process

Configuring

You can configure the router via the WebUI Settings page.

1. Launch the Internet Explorer browser, and enter http://192.168.10.1 in the address bar.
2. Enter the username and password to log in to the WebUI. The default username is ClaroAdministrador. You can refer to the label of the router for the default password. It’s strongly suggested to change the default login password of the WebUI to prevent unauthorized users from changing the routers’ settings.

Connect to Wi-Fi Network

You can connect your computer or mobile phone to the router’s Wi-Fi network.
Please refer to the label of the router for the default Wi-Fi SSID and the password.
It’s strongly suggested to change the default SSID and password by accessing the WebUI Wi-Fi management page to prevent unauthorized access to your Wi-Fi network.
You need to reconnect to the router’s Wi-Fi network after changing the Wi-Fi password.

Access the internet via the WAN port

You can connect the router’s WAN port to the wall-mounted Ethernet port by Ethernet cable, and configure the PPPoE/Static/DHCP parameters to access the internet.

VoLTE, VoIP & CS Domain Voice Call

The router supports VoLTE, VoIP, and CS domain voice call services. You can change the call mode via WebUI.
Please contact your service provider for more information.

FAQs & Troubleshooting

If you are expecting any issues with the router, in most cases please try to restart the router or restore the router to the factory settings.
The illustrations in this guide are for reference purposes only and may not reflect the exact appearance of your product. Please contact your service provider for more information.

hold the reset button for about 3 seconds until the indicator starts to blink.
Restoring factory settings will clear all user settings.
How to connect the router by the Wi-Fi Protected Setup (WPS)?| 1. Ensure that Wi-Fi is enabled on the client.
2. Press the WPS button on the router to set up a WPS connection
How to deal with the content display issue of the WebUI?| Manually clear browser’s cache, for example, open Internet Explorer the browser and choose Internet Options >General > Browsing history >Delete, and re-launch the WebUI page.
Why the router does not work after I have finished configuring?| 1. Ensure that you have a working SIM card inserted properly.
2. Move the router to an open space free from obstructions and make
sure there are available mobile networks.
3. If the problem persists, please contact your service provider.
Why can’t I access the WebUI of the router?| 1. Ensure that your computer is connected to the router through Wi-Fi or Ethernet cable.
2. Ensure that your computer is set to obtain an IP address and DNS server address automatically.
3. Restart your browser or try using another browser.
4. If the problem persists, restore the router to factory settings and try to access WebUI again.

• Some electronic devices may be susceptible to electromagnetic interference. Locate the router away from any TV set, radio, and other electronic equipment to avoid electromagnetic interference.
• The router may interfere with medical devices, such as hearing aids and pacemakers. Consult a physician or the manufacturer of the medical device before using the router.
• Please keep yourself at least 20 centimeters away from the router.
• Do not use your router in dangerous environments such as oil terminals or chemical factories where there are explosive gases or explosive products being processed.
• Please use original accessories or accessories that are authorized by. Unauthorized accessories may affect the router’s performance, damage the router, or cause danger to you.
• Do not attempt to dismantle the router. There are no user-serviceable parts.
• Do not allow the router or accessories to come into contact with liquid or moisture at any time. Do not immerse the router in any liquid.
• Do not place objects on top of the router. This may lead to overheating of the device.
• The device must be placed in a ventilation environment for use.
• Do not expose the router to direct sunlight or store it in hot. High temperatures can shorten the life of electronic devices.
• Do not allow children to play with the router or charger.
• Keep the length of the cable between the router and the phone less than 10 meters.
• The router is for indoor use only. Do not use the router outside. Do not connect telephone extensions that run outside of the building. These can result in lightning damage to your unit.

Cleaning and Maintaining

• Use an antistatic cloth to clean the router. Do not use chemical or abrasive cleaners as these could damage the plastic case. Turn off your router before you clean it.
• Use the router within the temperature range of 0℃～ +45℃, and the storage temperature range is -20℃～+70℃. The humidity range is 5%~95%.
• Do not remove your SIM card unnecessarily. The SIM card may be easily lost or it can be damaged by static electricity.
• Use an antistatic cloth to clean the router. Do not use chemical or abrasive cleaners as these could damage the plastic case. Turn off your router before you clean it.
• Use the router within the temperature range of 0℃～ +45℃, and the storage temperature range is -20℃～+70℃. The humidity range is 5%~95%.
• Do not remove your SIM card unnecessarily. The SIM card may be easily lost or it can be damaged by static electricity.

FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Federal Communication Commission (FCC) Radiation Exposure Statement.
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>