JOOAN A6M-U Smart Camera User Guide
- June 2, 2024
- JOOAN
Table of Contents
JOOAN A6M-U Smart Camera
Product Information
Specifications
- Compliance: Part 15 of FCC rules
- Radiation Exposure: FCC limits for an uncontrolled environment
- Minimum Distance: 20cm between radiator and body
Product Usage Instructions
FCC Warning
This device complies with part 15 of the FCC rules. To ensure proper operation, follow these conditions:
- This device must not cause harmful interference.
- The device must accept any interference received, including undesired operation.
Radiation Exposure Statement
For radiation safety, follow these guidelines:
- Ensure the equipment is installed with a minimum distance of 20cm between the radiator and your body.
- Operate the device with caution to maintain this distance.
FAQ
- Q: What should I do if I encounter interference with the device?
- A: If you experience interference, ensure that the device is not causing harmful interference. Try adjusting the placement or location of the device to minimize interference.
- Q : Can I modify the equipment?
- A: Changes or modifications not approved by the responsible party could void your authority to operate the equipment. Contact customer support for any modifications.
Camera Introduction
Note: The reset button position will be different for different models, and the picture is for reference only
Sign up & Login
- Register an account: Click”sign up”> enter Email, set your API password, check the verified code
Login
Note: i f you don’t want to register an account, it can’t remote, but you can use stand-alone mode to view the camera. This mode only supports Local view
WiFi connection
Power and Reset the camera: Pis plug the adapter for the camera and reset the
camera by long pressing the reset button for 5 seconds until you hear “Di-“,
the camera will do self-inspection after “Di-“2 times Requirement Before Wifi
connection: pls read Q1 above: Don’t ban permissions of the APP
NOTE : some models only support 2.4Ghz WiFi, cellphones connected to 2.4G
WiFi for the first connection; if the camera supports 2.4G/5G dual-band WiFi,
pls choose the right WiFi according to the place you want to install (2.4Ghz
signal transfer distance longer, 5Ghz is shorter but faster in speed).
-
In the APP: click”+”> select”WiFi connection”
-
Check “configure the network when you hear the device tone” > Tap” next step”
-
Follow the Tips Shown in the APP(pls connect WiFi to JA- or JAA-, and then back to Cam720 APP)to find the Camera’s WiFi(namedJA-** / JAA-***),after connected it pls back to cam720 APP
-
Enter the right password for the WiFi that your phone is connected to, Tap”Next Step)
-
When the device is connected, pls wait patiently until camera is online”, then click the video to view
Bluetooth configuration
- Please confirm that the Bluetooth function is turned on.
- After resetting the camera, wait for it to “Di” two sounds, until the camera completes the self-test.
- In the APP: Click “+” and wait for 1-2 seconds for the APP to automatically search for the camera Bluetooth signal.
- Select the Bluetooth signal of the camera, input the WiFi password and click Next.
- Wait patiently during Bluetooth network configuration, please do not exit halfway.
Note : Please ignore if you don’t need Bluetooth network configuration. If you need to use it again, please close the app and then re-open it.
Wired Connection
Plug the power supply and Ethernet cable into the router: Pls plug the adapter
for the camera and connect the camera with the Ethernet cable to the router
Reset the camera: Long-press the reset button about 5-8s until you hear
Prompted, and select a wired connection to connect it.
NOTE: pls read Q2 above if there is a problem with the wired connection
if the camera has a Network port, it supports a wired/WiFi connection,
otherwise, pls select a Wi-Fi connection to connect.
- In the APP, click”+”> select “network cable connection”
- Search and select the IP of the camera, click to add
- Click the video to view until hearing “camera is online”
- Return to the device list
- Share the device
- More function settings
- Switch image effects
- Turn on the microphone
- Screenshot to save the image
- Swich into a Full-screen image
- Playback (SD card Playback | Cloud Playback)
- Setting of cruise
- Preset point settings
- TZP rotation control
- Turn on the voice intercom
- Turn on the screen record function
- Start Live video
- Subscribe Cloud storage
- More functions setup
- User information
- Modify the device name
- Back to the device list
- Modify the device name
- Share equipment
- SD card setup
- Detection alarm settings
- Buy cloud storage
- Image Flip: upside down
- Choose a call mode
- Enable/Disable Auto tracking
- Indicator light switch
- Choose night vision mode
- Set the time zone
- Switch WIFI network
- Camera information
- Camera version number
- Delete the camera
- Transfer the camera to another account
Share
Share your camera with your friends and families
- Your friend should have an account with the cam720 APP.
- in the main account, enter the Email of the friend’s APP account or scan the QR code of the account to share it.
- Freely set the permission on this shared account.
Playback
- Turn on the playback function and two Record methods are available: SDcard record (8-128G) and Cloud Record.
- New users can get a trial of cloud storage for free, pls don’t miss it.
- SD card record supports 3 record modes: 24/7 continuous, motion-triggered, and scheduled record.
Installation
Indoor Camera-stent assembly
-
This camera can be placed on the desktop, or do ceil or wall-mounted.
-
Attach the bracket to the wall make a mark on the hole to punch holes, and use a 6mm drill bit to get the holes, then Stuff the rubber stopper into the hole.
-
Align the bracket with the hole position and tighten the screws. Fix the body, hold the body and turn it tightly.
-
This camera can be placed on the desktop, or ceil or wall-mounted.
-
Attach the bracket to the wall and make a mark on the hole to ponch holes, and use a 6mm drill bit to get the holes, then Stuff the rubber stopper into the hole.
-
Align the bracket with the hole position and tighten the screws. Fix the body, hold the body and turn it tightly.
Outdoor camera
- Put the other end of bracket A together with the slot of bracket B, and then just push it down.
- Select a suitable location and install expansion screws on the wall. for example, if it’s a wooden wall, expansion screws are not required.
- Align the bracket with the hole position and tighten the screws.
Important Use Notice
- The use of unapproved or incompatible power adapters may cause fire, explosion or other dangers.
- This product and accessories contain some small parts to avoid children’s contact and cause swallowing small parts, causing suffocation or other hazards, in addition, this product is not a toy, so children should be used under adult supervision.
- Please use this product within the appropriate temperature range. When the ambient temperature is too high or too low, it may cause errors, and avoid rain or moisture on the product and its accessories, so as not to affect the use of the product.
- Suitable for equipment, suitable for areas with an altitude of 2000 meters and below.
- The Wi-Fi device should be under a good wifi signal area, pls avoid choosing a closed environment installation which may cause a bad signal.
Important Use Notice
-
Failed in connection at first connection?
Pis view the operation video on the last page(Scan the QR code to view), and pls view the wifi connection steps from Page 6, if still fails, pls message the seller to get support, we also offer online support if you need it. -
Change a router, camera is offline?
pls delete the camera from the APP, take the camera to near the new router, power and reset it, search and add it. -
Stop record?
-
Check the status of the SD card in the APP
-
Check the record setup support
-
format SD card
-
change an SD card to test
-
message the Seller to get
-
The camera is offline?
Read the Q3 page and follow it to check, if there are further questions, pls message the seller to get support -
The instructions are not detailed enough?
It’s a general quick user guide, so less many fewer details, pls contact the seller toget the E-user manual and operation video according to your order.
FAQ
-
What should I pay attention to before WiFi connection?
A1: APP permission: Pls turn on GPS and all permissions and select”allow”; iOS iPhone: pls enable location action by setting ›privacy>location services> cam720 APP>enablepreciselocation, select”always” WiFi requirement: Pls ensure the Name and password ofthe router are not more than 16 characters Note : pls take the camera near the router for the first connection, cellphone connected to the same wifi -
What should I pay attention to before Wired connection?
A2 : Ethernet cable: pls check the cable is working and check the indicator that the network port is always on note: pls confirm the cellphone is connected to the same wifi of the router that the camera is connected. -
What to do if the camera is often offline?
A3: Adapter: pls check the adapter and outlet for the camera, or check the camera’s record, if there are some broken records, the problem is in power; the camera can record without wifi Network: pls check the network, is it a normal APP permission: pls check mobile network permission on the APP is enable, otherwise, the APP can’t work under mobile network. Reconfigure the camera: delete the camera from the APP> add the camera after resetting the camera as the first connection
FCC STATEMENT
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two
conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
contact
After-sale Service & Tech Support
We offer a one-year warranty and lifetime technical support! As long as there
is any problem, please feel free to contact the purchase store, we will
quickly provide an effective solution.
By scanning the QR code below to access YouTube, Selectthe the right operation video for your camera according to the model of the camera Or message the seller to get the operation video directly.
Download CAM720 APP from the APP store or Google Play, or by Scanning the QR code above. Sign up an account by email and log in, please read the instructions carefully before use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>