JOOAN B0BZJD7RPV 3MP Wireless Security Camera System Outdoor User Manual

: June 16, 2024
: JOOAN

Table of Contents

Statement
Safety Caution
Unpack Audit
Product Overview
installation instructions
NVR system operation
Extend WiFi Range
OPERATE NVR SYSTEM FROM CLIENT ON PC
OPERATE NVR SYSTEM ON MOBILE DEVICE
Warning
Q&A
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WIRELESS KIT
QUICK USER GUIDE

Statement

Thank you for purchasing our product! This quick user guide will talk about main usages of the product. More information can be found on our website and the help center. The functions, parameters, operations, etc. presented in this manual are for reference only, and Jooan may improve the content. For all specific information, please refer to the actual product.

Safety Caution

Please do not put any fluid container on the product.
Please use the product in ventilated environment and prevent blocking the vents.
Please use included power supply with the product to prevent damage to the product.
Please use the product under its standard working temperature and humidity.(advised in this manual or distributor’s website)
Dust on PCB may cause short circuit. It is suggested to clean the dust on PCB timely to make the product work properly.
Please obey the regulation and policy in your country and area during the installation of this product.

Unpack Audit

After receiving the product, please check all products and accessories according to the follow Packing list information. If anything is missed or damaged, please contact us.

Packing list

S/N| Item| Quantity
1| WiFi NVR| 1pcs
2| DC 12V2A power supply (for NVR)| 1 pcs
3| WIFI IP camera| 4/8pcs
4| DC 12V1A power supply (for IPC)| 4/8pcs
5| Screw bag (for IPC)| 4/8pcs
6| Antenna(for IPC)| 4/8pcs
7| User manual(Contains 4 screws for HDD)| 1pcs
8| Antenna extension| 1pcs
9| HDMI cable| 1pcs
10| Ethernet cable| 1pcs
11| Mouse| 1pcs
12| Warnning Post| 1pcs

Product Overview

This product may require cabling, we suggest to test all products&parts before installation and cabling.
NVR

WIFI Antenna Ports: Double antennas to WIFI range;
AUDIO OUT: 3.5mm audio interface for external speakers;
VGA Port: For viewing on VGA monitor;
HD OUTPUT Port: For viewing on HDTV;
WAN Port: Connect your NVR to the Internet;
USB Ports: For mouse and backup
Power Input: 12V 2A NVR power interface;

IPC

WiFi antenna: WiFi connection with NVR;
DC Port: Input power 12V 1A;
Reset button: Press reset button for 10 seconds to restore factory setting and enter into matching-code mode.
Photosensitive: Used to measure light and control the turning on of infrared light.

installation instructions

HDD installation
Notes:

To use the video recording and playback functions, HDD must be installed.
The camera system doesn’t come with hard drive. Recommend to choose an Monitoring dedicated Hard Drive in SATA III 3.5″, 1-2TB .

Step 1: Loose the screws which are fixing the box cover. Step 2: Push forward the cover to the end and remove it. Step 3: Connect the SATA power and data cables of the NVR to the corresponding ports of the Hard Disk Drive.(NO HDD). Step 4: Hold the Hard Disk Drive and the NVR together,carefully turn them over,then align the screw holes on the Hard Disk Drive with the screw holes on the NVR housing and put screw on. Step 5: Put the cover back to position and install the screws. KIT installation
This system is standalone with embedded Linux Operating System in the NVR. Just like a desktop PC, need to hook a screen to the NVR to enter the OS. Any TV , monitor with VGA or HD-OUTPUT input should work for it. Add the cameras to the NVR
Step 1: Install antennas for cameras;
Step 2: Connect a screen to the NVR via its HD-OUT port or VGA port.(The default supported screen size is 19-42″.).
Step 3: Plug the NVR to power.(use bigger 12V 2A power adapter.)
Step 4: Plug cameras to power.(use smaller 12V 1A power adapters.)
Step 5: Within seconds, you can see camera’s images on the screen.
Step 6: Plug the mouse to USB port on the back of NVR. So you can operate the system.
Default ID: admin
Password: none (means leaving the password empty, just click login).
Tips: To protect your privacy, please set your password at earliest convenience. Right click -> System Setup -> System Admin -> User Management to set password.
※ What should I do if I can’t connect to the camera?
Please kindly follow below steps to add them to the NVR:
Step 1: Powered on the camera. Press and hold phorosensitive to observe if the infrared light of the camera is on.
Step 2: Right click -> video manage -> Delete the not working camera.
Step 3: Put the camera close to the NVR and power on it.
Step 4: Push the reset button of the camera 5-10 seconds or longer time to restore it to factory setting.
Step 5: Use “wireless add” function to add it to the NVR, wait patiently for a while, the system will automatically search the camera and match code.

NVR system operation

Format the hard disk
Steps:
After installing HDD, boot up the NVR -> Right click -> System Setup -> General Setup -> HDD Setup -> format the HDD.
Note:
Recommend to choose an Monitoring dedicated Hard Drive in SATA III 3.5″, 1-2TB .The hard disk is installed on the device for the first time, and the hard disk needs to be formatted. Video Record
Steps: Right click -> System Setup -> Record Setup -> Record Plan.
Notes:

The recording function can only be used after installing a hard disk.
The record time depends on the capacity of hard drive.When the hard drive is full,the new video overwrite the old one automatically. For example, if the hard drive is full after 7 days,then the 8th day video will cover the 1st day.
Users can set up any period of time they want When NVR detects hard disk, the default setting will be 24hours 7 days recording.
Time Recording: Click “Time” and put mouse icon on the upper left corner (for example “T” as picture shows), press and drag the mouse to the right to choose the time. The selected area will turn to red.
Motion Recording: Click “Motion” and put mouse icon on the upper left corner (for example “T” as picture shows), press and drag the mouse to the right to choose the time. The selected area will turn to green.
Alarm Recording: Click “Alarm” and put mouse icon on the upper left corner (for example “T” as picture shows), press and drag the mouse to the right to choose the time. The list will turn to yellow.

Video Playback
Steps: Right click -> Video Playback -> choose date, channel, record mode -> click “Search”

Video search condition area: You can select the date, time, channel, and event type to query the video, and click “search” to query.
Video search result area: Display the video search results under the search conditions you set. Different colors represent different event types.
Video playback control keys: Play, pause, fast forward
Time progress bar area: Time progress bar area shows the currently playing video time, event type, and you can drag the progress bar to perform fast forward and rewind operations.
Progress bar mode switch: Switch the progress bar display mode, choose to use the unit of day or hour.
Backup: After selecting the file, click “Backup”, a reminder of “Please insert USB” pops up, pull out the mouse and insert the U disk within one minute.
Exit: Right click or click “exit” to exit the video playback.

Video Backup
Steps:
Right click -> Video Backup -> choose backup channel -> choose record mode -> setup searching time -> choose recording file on the list -> video backup, insert U disk within reminding 1 minute, then the system will backup recording file to U disk.
Note:
Please format the U disk as FAT32 before backing up. Motion Detection
Steps:
Right click -> System Setup -> Channel Setup -> Video Detection

Select the channel to enable motion detection and set the channel detec- tion type (movement, video loss, video occlusion, etc). When the alarm sensitivity is too high or too low, the sensitivity can be adjusted to achieve the best effect.
When a moving object is detected, the alarm information can be received by means of buzzer, mail, app, etc. App operation details are in Chapter 9 and email operation details are in page 9.
Option to copy the same settings to different channels.
Motion detection arming time, default 24h.
Customize the motion detection area(Default all selected). The selected area starts motion detection, and the unselected area turns off.

E-Mail Setup
Steps:
Right click mouse -> System Setup -> Network Setup -> E-Mail
Note:
To add email to the NVR, SMTP/IMAP must be enabled in the email settings.
The steps are as follows:
Step 1: login the mail box on email official website.
Step 2: enter settings and enable SMTP/IMAP service and set a authorization code(available in some email settings,not all).
Step 3: Add the email address and password to the NVR, you have to input the authorization code as password if the code is unavailable. MENU Function other function
Right click the mouse to show the main Menu bar as shown below, right click again to return or exit the current menu.

Split Screen: change the numbers of the channels showing in the same screen.
Video Manage: manage IP cameras and channels, image rollover, match code ect.
System setup: includes General Setup, Record Setup, Network Setup, Channel Setup and System Admin.
General Setup: change language, NVR resolution, time setup, HDD information, error setup etc.
Record Setup: Set various types of recording time period.
Network Setup: DHCP, NVR’s IP address, network status, cloud ID, e-mail setup, wireless setup ect.
Channel Setup: change encode mode, camera resolution, motion detection ect.
System Admin: system version, set password, edit users, simple restore ect.
Video Playback: playback recorded videos.
Video Backup: backup recorded videos.
Color Adjust: adjust the brightness, contrast, sharpness ect. Of the picture in each channel.
PTZ Control: enter PTZ control to control camera. (requires camera to support this function.)
Volume: adjust volume of audio cameras.(works only for audio cameras.)
Fast Network: configure the network.
Wireless Add: add devices by matching code.
Exit System: Logout, reboot, close screen output and shut down the system.

Extend WiFi Range

Because of the character of WIFI, the WIFI signal will weaker when going through the wall, stairs and other obstacles. We can use some methods to be applied to bypass obstacles and extend WIFI range.
Position the Antenna Correctly
WIFI range is like an apple and the antenna of NVR is in the center of it. WIFI signal is strong all around the WIFI range. Antenna of NVR should be put straight up, if not, WIFI signal will be weak. According to the signal transmission character of antenna, the antenna of cameras should overlap or parallel to NVR WIFI range, as pictures showed below. Notes:
Please place the NVR far away from the devices that are easy to interfere the connection, such as microwave oven, TV ect. Make sure the obstacles between the NVR and the cameras are as few as possible.
Repeater Setup
As picture shown above, when IPCAM1 is put somewhere out of NVR WIFI range, and there is IPCAM2 between them with strong WIFI signal, users can put IPCAM1 close to NVR and power it, setup IPCAM1 repeated by IPCAM2, and then install IPCAM1 to the presupposed place. Notes:
The repeater cannot strengthen the WiFi signal, but can extend the WiFi distance by the IP camera. Set up cascading connection in a reasonable solution, extend wifi signal transfer distance.
Step 1: Right click -> Video Setup -> Repeater Step 2: Click + to select the channel with the stronger signal value to connect to the NVR, and the weaker signal value to connect to the channel with stronger signal value. As shown in the picture, the signal values of CH1 and CH2 are strong. We can connect CH3 and CH4 behind CH1 and CH2. Step 3: Click “Apply” to finish the cascading connection. Click “Refresh” to check if it’s set successfully. To cancel selection, click on the seleted channel, then click “Apply” and “Ok”.
Use Antenna Extension
Installation method of antenna extension cord Note:
When wireless signal is weaker, users can take off the original antenna and subtitute antenna extension cord. Drill a hole on the wall to let the extension cord go through and simply put it where wireless signal is strong.

OPERATE NVR SYSTEM FROM CLIENT ON PC

Please download the EseeCloud client through http://k.jooan.cc
Note:
This function needs to be connected to the network, please confirm the status of the NVR network in advance.
Login
Login Local: Log in to EseeCloud Client with default user name (admin) and Password (empty, namely enter nothing) if you did not set any password.
Login Cloud: You can also register an account by phone number or email address. Add Device
Add device by via LAN
Click “Device Management”. After entering the interface, it will automatically
search for devices and find your own device, then click “Add”. Add device by IP address
Switch to IP address option. Enter IP address of your device(Please choose the appropriate device type and number of channels.) Add device by Cloud ID
Switch to Cloud ID option. Enter cloud ID of your device (Password is empty, namely enter nothing if you did not set any password.), click “Finish” and add device. (Please choose the appropriate device type and number of channels.) Bottom Menu

| Playback:
video playback and download.
---|---
| Device Management:
add and delete device, modify information of device.
| User Parameter:
change language, change the file path of saving ect.
| Record:
record the current video into your computer.
| Screenshot:
take a screenshot of the current screen and save it into your computer.
| Disconnect All:
disconnect the device
| Screen Number:
change the channel numbers showing in the screen.
| More Funtion:
user information, change password, client version ect.

OPERATE NVR SYSTEM ON MOBILE DEVICE

Note:
This function needs to be connected to the network, please confirm the status of the NVR network in advance.
Download
Search and download EseeCloud from App store/Google Play or scan the QR codes below to download.

|
---|---
http://www.dvr163.com/download/android.php?l=en| http://www.dvr163.com/download/ios.php?l=en

Add Device
Install and open EseeCloud App, then follow the steps below to add the NVR system.
Step 1: Register an account and log in to EseeCloud, then + icon in the center or on the upper right corner to add device. Step 2: You can add NVR by scanning the cloud ID, or you can add it in other ways. (Click “Kit”, manually enter the cloud ID and password to add the NVR.)

Warning

Notes:
Device will not be in guarantee if caused by below reason

Product failure due to accident, negligence, disaster, improper operation or misuse.
Do not conform to the environment and conditions, such as power improper, working temperature too high or too low, lightning stroke.etc.
Ever be maintained by other center which not belong to the real factory.
Goods already sold more than 12 months.

Warranty Card
12-month warranty for quality-related issues
For 12 month after the date of purchase, we take care of all quality-related issues with a Replacement or rull refund. (RemindenBe sure to use your product as directed.)
Warranty-related shipping costs can only be covered in the country of purchase. If the product is taken outside the country of purchase,any shipping costs will be the buyer’s Responsibility.
Alternatively,we can offer a 50% refund of the item’s purchase price without the need to return.
If returning an item,please ship it back within 20 days after you receive approval. Further delay may void your return.
30-day money-back guarantee for any reason
1 For 30 days after the date of purchase,return your undamaged product and receive a full 1 ! refund for ANY reason.

Q&A

Q1: Camera connection failed or no image.

It maybe the camera did not match the code successfully,Please kindly follow page 5 to add them to the NVR.

Q2: Can I add the extra new camera?

The camera with the same brand is recommended when you’d like to add more cameras. To get the link of buying camera and the detailed guide for adding the camera, please contact us at market@qacctv.com.

Q3: NVR system can not detect the Hard Disk Drive.

Q4: What should I do if I forget the password for logging in to the NVR?

For the privacy of users, please contact us at market@qacctv.com, and the technician will help you.

Q5: No display on the Monitor of the NVR system.

It might be mainly caused by resolution compatibility. The default reso- lution of the NVR is 1280*1024, which may not be compatible with some monitors. Here are some methods for solving the issue:

Replace the display
Step 1: Connect the NVR to other monitor via the VGA output or HDMI output to s ee if you can enter the Menu bar of the NVR.
Step 2: When you are able to see the Menu, please go to System Setup -> General Setup -> General Setup -> Display Resolution to adjust the appropriate resolution, then click Ok. (For larger monitors, please choose 1024*768.)
Step 3: Connect the NVR to your primary screen via again to check the dispaly.
Set by IP address
Step 1: Download the EseeCloud client on your computer. (The operation is on page 14.)
Step 2: Connect the NVR and your computer to the same network.
Step 3: Open the EseeCloud client and search the IP address of the NVR through the LAN.
Step 4: Enter the IP address of the NVR in the browser for the manage- ment interface. (Password is empty, namely enter nothing if you did not set any password. The operation details are in Chapter 8.)
Step 5: Setting->Ordinary->VGA resolution->Save Step 6: Connect the NVR to your primary screen via again to check the dispaly.