Reolink 2312A Video Doorbell PoE User Manual
- June 2, 2024
- reolink
Table of Contents
Quick Start Guide
Apply to: Reolink Video Doorbell PoE
What’s in the Box
Doorbell Introduction
Video Doorbell PoE
Set up the Doorbell
Set up the Doorbell on Phone
Step 1
Scan to download the Reolink App from the App Store or Google Play Store.
https://reolink.com/wp-json/reo-v2/app/download
NOTE: If the Reolink App is already existed, please check if it is the
newest; if no, please update it.
Step 2
Power on the video doorbell.
PoE Version:
- Power the doorbell on by connecting it to a PoE Switch/Injector or a Reolink PoE NVR (not included in the package).
- Connect the PoE Switch/Injector/Reolink PoE NVR to the LAN Port on the router.
NOTE: The Reolink NVR should be upgraded to the latest firmware version.
NOTE:
It is recommended to setup the Internet before the installation. Make sure the
Y-shape plugs are separate from each other.
Step 3
Launch the Reolink App. Click the “ ” button in the top right corner and
scan the QR code on the doorbell and follow the onscreen instructions to
finish the initial setup.
Set up the Doorbell on PC (Optional)
Step 1
Download and install the Reolink Client. Go to
https://reolink.com>Support>App&Client
Step 2
Power on the video doorbell.
Step 3
Launch the Reolink Client. Click the “ ” button and input the UID number of
the doorbell to add it.
Step 4
Follow the onscreen instructions to finish the initial setup.
Install the Doorbell
Step 1
Put the mounting hole template on the wall by the door and drill holes as
shown.
Step 2
Install the mounting plate using the long screws provided through the two
holes.
For the PoE Version:
Step 3
Run the Ethernet cable through the mounting plate and the hole on the wall to
connect it to the doorbell, then attach the doorbell to the plate.
Step 4
The doorbell is powered by connecting the other end of the Ethernet cable to a
PoE device.
Install a Wedge (Optional)
If you need to adjust the angle of the doorbell, you can use the wedge
provided. (The Reolink Video Doorbell PoE is taken as an example)
Step 1
Put the mounting hole template on the wall and drill holes as shown.
Step 2
Install the wedge using the screws provided through the two holes. Ensure that
the notched side of the wedge is facing outside.
Step 3
Screw the mounting plate to the wedge.
Step 4
Run the Ethernet cable through the wedge and mounting plate, and attach the
doorbell to the plate.
Remove the Doorbell
If you want to remove the doorbell from the mounting plate, you may use the
reset needle to poke the bottom.
Specification
Hardware Features
Field of View: 133.6° Horizontal, 97.3° Vertical, 180.4° Diagonal
Dimension: 133 x 48 x 23mm
Weight: 96g
Notification of Compliance
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: this device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 20cm between the radiator & body.
** Simplified EU Declaration of Conformity
The PoE camera is in compliance with Directive 2014/30/EU.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes.throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Official Store or a Reolink authorized reseller. Learn
more: https://reolink.com/warranty-and-return/.
NOTE: We hope that you enjoy the new purchase. But if you are not
satisfied with the product and plan to return, we strongly suggest that you
reset the camera to factory default settings before returning.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of reach of children.
End User License Agreement
By using the Product Software that is embedded on the Reolink product, you
agree to the terms of this End User License Agreement (“EULA”) between you and
Reolink. Learn more: https://reolink.com/eula/.
ISED Statements**
This device contains licence-exempt transmitter(s)/re ceiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency Exposure Statement for IC
The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions.
The min separation distance is 20cm.
The functions of Wireless Access Systems including Radio Local Area
Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are
restricted to indoor use only within all European
Union countries (BE/BG/CZ/DK/DE/EE/IE/EL/ES/FR/HR/ IT/CY/LV/LT/
LU/HU/MT/NL/AT/PL/PT/RO/SI/SK/FI/SE/TR/N O/CH/IS/LI/UK(NI)
Technical Support
If you need any technical help, please visit our official support site and
contact our support team before returning the products:
https://support.reolink.com. 
References
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Official: Security Cameras and Systems for Home & Business
- Warranty & Return – Reolink
- Reolink Support - Official Reolink Help Center
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>