WELLFOR W8MCL2030 L-R LED Mirrored Bathroom Cabinet Installation Guide

WELLFOR W8MCL2030 L-R LED Mirrored Bathroom Cabinet

Product Information

Specifications

• Model: W8MCL2030 L/R, W8MCL2430 L/R, W8MCL3030, W8MCL3630
• Dimensions:
  • W8MCL2030L/R: 19-1/4 x 29-1/4 x 3-3/4 inches
  • W8MCL2430(L/R): 23-1/4 x 29-1/4 x 3-3/4 inches
  • W8MCL3030: 29-1/4 x 29-1/4 x 3-3/4 inches
  • W8MCL3630: 35-1/4 x 29-1/4 x 3-3/4 inches

FAQ

• Q: Can this product be used outdoors?
• A: No, this furnishing should not be used outdoors.

PRODUCT SERIES INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed, Requires two(2) persons in installation.

• DANGER: READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS MIRROR CABINET
• WARNING: To reduce the risk of burns, fire, electric shock or injury to persons. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening. Do not use outdoors.
• WARNING: Risk of electric shock. Connect this furnishing to a properly grounded circuit only. See Grounding instructions.

GROUNDING INSTRUCTIONS

WARNING

• This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.
• An Electrical option cabinet must be wired to a 20 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.

NOTE: To ensure the normal use of a product, it is required to set out wires as per the regulations of IEE. The product is only applicating to indoor installation. The installation must be executed by a professional electrician, wrong installation may lead to product damage and personal injury.

ELECTRIC CONNECTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN

• WARNING: Shut off power before wiring the mirror.
• WARNING: An Electrical option mirror must be wired to a 20 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.
• WARNING: This mirror must be connected to a grounded, metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the mirror.
• CAUTION: Requires 120 VAC 20 Amp GFI protected circuit.

Electric wiring: Be sure to provide enough wire to make the proper and safe connection to the Field/Power.

MIRROR FEATURES

• Copper free silver mirror
• High output LED lighting: CRI 90+, 2700-6400K CCT, IP44
• Color Temperature changing touch switch for surface LED
• Recess mount or wall surface mount
• Defogger

TOOLS REQUIRED FOR ASSEMBLY

PARTS INCLUDED

NOTE: Determine overall mirror dimensions before installation. Requires two(2) person in installation.
Accessories and parts may vary from the picture above. Depends on the product model and size.*

DIMENSIONS

NOTE: Please use roughly in size for recess mounting installation(wall cut-out). All dimensions and specifications are nominal and may vary.Use actual products for accuracy in critical situations.

NOTE: All rough-in dimensions are for reference only!

PRIOR TO MOUNTING

Remove the Door(s) prior to mounting your cabinet(s)

1. Carefully remove side mirror panels for recess mount installation.
2. Remove door(s) prior to mounting your cabinet.Start with unplugging the door from the cabine
3. While supporting the door release(the lever under the hinge arm), slide the door off the frame.
4. Take off the door(s) carefully and lay it down on a safe area.

RECESS INSTALLATION

• Refer to “dimensions” on page 4 to measure Draw the perimeter of the cabinet on the wall. Rough in size.

NOTE: To recess mount, the wall cavity must be framed and the cabinet secured to framing studs. Reroute electrical or water supply lines from the cavity. Consult a professional if drain or vent piping is encountered, or if the wall is load-bearing.

• Draw the perimeter of the cabinet on the wall.

• Cut the hole as the marked dimension with a suitable tool.

• Frame the opening for the cabinet based on the measurements.

• First cut off the power plug, then use the WIRE CONNECTOR to connect to the external power supply.

WARNING: Turn off the power before the wire connection!

• Position cabinet in cut out opening.

• Connect electrical wires and then place the cabinet between the wall studs.

• Affix using hardware screws into the studs.

NOTE: For the wood stud wall, you need to use a screw to fix the cabinet.
For brick/concrete/stone/tile walls, you need to use a wall plug and screw together to fix the cabinet.

SURFACE-MOUNTED INSTALLATION

• Level and mark the cabinet’s location on the wall.

• Mark the position of the Bottom Mounting Bracket and Punch.

• Bottom mounting brackets must be attached to furring strip/channel or wall studs

• Punch holes in the mark, put in Wall Plug, fix Bottom Mounting Bracket to the wall with a Screw.

• With assistance, to rest the cabinet on the mounting bracket and hold in place.
• Make sure the cabinet is leveled and fully inserted into the groove of the bottom bracket.

• Insert top mounting bracket into the top of the cabinet.

• Make sure top brackets are locked in the grooves.

• Adjust the position of Top Mounting Bracket and mark the holes with a pencil

• Remove the cabinet, drill holes according to the marked position, and put in Wall Plugs.

• Put the cabinet on the bottom mounting bracket and hold the place, then insert the top mounting bracket into the top of the cabinet, fix the top mounting brackets to the holes with a screw.(repeat step 4-6 )

NOTE: Vibrations occur in the electric drill, use a Philips Screwdriver to protect your cabinet top surface.

Top mounting brackets must attached to furring strip/channel or wall studs.

• Test the fit of the cabinet before Final assembly.

• Make sure cabinet is leveled and fully inserted into the groove of the bracket.
• Install the side mirrors

• Put the plug into the socket

GLASS SHELF INSTALLATION

• Insert clear snap-in shelf clips into holes on the sides of the cabinet.
• Insert the Glass Shelf along the board clip slot

MIRROR DOOR INSTALLATION

1. Slide the doors into place by pinching the end of the hinges.
2. Plug the door into the cabinet.

• Press the end of the hinge to match the hinge seat
• Installing wiring terminals

Door Adjustment / Door Remov

OPTIONAL DOOR ADJUSTMENT
Doors may need to be adjusted after the initial shipping of the cabinet. The cabinet doors have a three-way adjustment feature. Height, side-to-side, level and depth can be adjusted. With the hinge slightly closed you can access the middle screw for up/down adjustment. With the hinge fully extended you can access the front and back screws. These screws will move the door side to side and in and out.

TOUCH BUTTON AND OUTLET CHARGER

How to use Defogger Switch and Dimmer Switch
Left touch Senor

• ON/OFF Anti-fog(The defogger power will automatically turn off after an hour) light brightness change from 10% to 100% by holding

Right Touch Sensor

• ON/OFF Lighting light temperature change from 2700K to 6500K by holding

OPERATION

1. Touch the sensor button to turn ON the light.
2. Touch and hold the light ON sensor button to change the light tempeture from 2700K to 6500K. Release the botton when the light tempeture reaches the desired colour.
3. Touch the sensor button to turn ON the defogger
4. Touch and hold the defogger ON sensor to dim the light.Release the button when the light reaches the desired brightness setting.
5. Inside LED Light with door switch sensor makes it a lighted medicine cabinet when you open the door. Open the door, Inside LED Light ON.

The mirrors are equipped with a memory feature to preserve the previous brightness setting.
How to use Outlet and USB Charger :
This lighted medicine cabinet contains an outlet and USB chargers.

1. Outlet Charger is 15Amp 110V AC to power shavers, or toothbrushes, but do not use it for Hair dryers, it may blow a circuit.
2. USB ports provide 4.2Amp 5V DC for charging purposes only, not for data transfer.

Suggestion: Turn off the mirror power supply if you don’t use it for a long time.

USE AND MAINTENANCE

WARNINGS

1. Please do not use if you found the mirror cabinet has been broken.
2. Never put any sharp or heavy material on the mirror surface, otherwise, the glass mirror will be broken and body injury accidents may occur.
3. Turn off the power switch in storm lightning weather to avoid electric parts damage.

Use and Maintenance
CAUTION
USE

1. To avoid damage, do NOT knock the mirror cabinet with any hard objects;

2. Do NOT clean the mirror cabinet with caustic cleaner.
   Do NOT wipe the mirror cabinet with a Bristle brush;

3. For daily maintenance, please use a soft cloth and mild cleaner to clean the mirror cabinet.

LIMITED WARRANTY

LIMITED WARRANTY TWO YEARS TERM

WELLFOR warrants to the original purchaser that, it will, at its election repair, replace, or make appropriate adjustments to products made by this company shown to have significant defects in material or workmanship which are reported to WELLFOR in writing within two (2)years from the date of delivery.WELLFOR is not responsible for installation costs. The warranty is void in the event the product is damaged in transit, or if damage or failure is caused by abuse, misuse, abnormal usage, faulty installation, damage in an accident, improper maintenance, or any repairs other than those authorized by WELLFOR. At the expiration of the two-year warranty period, WELLFOR shall be under no further obligation under any warranty, expressed or implied, including the implied warranty of merchantability. WELLFOR shall not be liable for any consequential damages arising out of or in connection with the use or performance of its products. Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or clusion may not apply to you. Any liability against WELLFOR under any implied warranty, including the warranty of merchantability, is expressly limited to the terms of this warranty. Permission to return any merchandise under this warranty must be authorized by WELLFOR and returned prepaid by the purchaser. Claims under this warranty should be sent directly to your dealer.

CONTACT

• For customer support please call 206.809.0093 on weekdays from 9:00 to 6:00 PST, or by email: at service@wellfor.com.
• For more information: www.wellfor.com

References

• WELLFOR | Bathroom Mirrors, Vanities, Medicine Cabinets

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>