Whirlpool WFE2B19 Dishwasher Instruction Manual

Whirlpool WFE2B19 Dishwasher

Product Information

Specifications

• Brand: Whirlpool
• Model: [Insert Model Number]
• Color: [Insert Color]
• Dimensions: [Insert Dimensions]
• Capacity: [Insert Capacity]

Product Description

The Whirlpool dishwasher is equipped with various features to ensure efficient cleaning of your dishes. It includes an upper rack, cutlery rack, foldable flaps, upper and lower spray arms, filter assembly, salt reservoir, detergent and rinse aid dispensers, and a control panel for easy operation.

Control Panel Features

• On-Off / Reset button with indicator light
• Program selection button with indicator light
• Multizone button with indicator light
• Turbo button with indicator light / Keylock
• Eco program indicator light
• Keylock indicator light
• Display
• Program number and remaining time indicator

Product Usage Instructions

First-Time Use – Salt, Rinse Aid, and Detergent
Advice Regarding the First Time Use: After installation, remove stoppers and elastic elements from the racks.

Filling the Salt Reservoir

1. Remove the lower rack and unscrew the reservoir cap.
2. Fill the salt reservoir with water for the first time.
3. Use a funnel to fill the salt reservoir up to its edge (approximately 1 kg).
4. Wipe any salt residue away from the opening and screw the cap on tightly.

Setting the Water Hardness: Refer to the Water Hardness Table and adjust the setting based on your local water hardness. Run a program without loading after setting water hardness.

Filling the Rinse Aid Dispenser
[Include Rinse Aid Dispenser Filling Instructions here]

FAQ

• Q: How often should I refill the salt reservoir?
  A: Refill the salt reservoir whenever the SALT REFILL indicator light is lit on the control panel. It is recommended to check and refill regularly to prevent damage to the water softener.

• Q: Can I use any type of dishwasher detergent with the salt?
  A: Yes, it is recommended to use salt specifically designed for dishwashers along with any type of dishwasher detergent for optimal performance.

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
To receive more complete assistance, please register your appliance on: www.whirlpool.eu/register
You can download the Safety Instructions and the User Manual, by visiting our website docs.whirlpool.eu and following the instructions on the back of this booklet.

Before using the appliance carefully read the Safety Instructions guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack
2. Cutlery rack
3. Foldable flaps
4. Upper rack height adjuster
5. Upper spray arm
6. Lower rack
7. Power Clean® support
8. Lower spray arm
9. Filter Assembly
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
13. Control panel

CONTROL PANEL

1. On-Off / Reset button with indicator light
2. Program selection button with indicator light
3. Multizone button with indicator light
4. Turbo button with indicator light / Keylock
5. Eco program indicator light
6. Keylock indicator light
7. Display
8. Program number and remaining time indicator
9. Tablet (Tab) indicator light
10. Closed water tap indicator light
11. Rinse Aid refill indicator light
12. Salt refill indicator light
13. Power Clean® button with indicator light
14. Tablet (Tab) button with indicator light
15. Delay button with indicator light
16. Start/Pause button with indicator light / Drain out

FIRST TIME USE

SALT, RINSE AID, AND DETERGENT

ADVICE REGARDING THE FIRST-TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.

• THE SALT RESERVOIR must BE NEVER EMPTY.
• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL indicator light in the control panel is lit .

1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt reservoir right up to its edge (approximately 1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work perfectly, it is essential that the water hardness setting is based on the actual water hardness in your house. This information can be obtained from your local water supplier. The factory sets the default value for the water hardness

• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down the button START/Pause for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The current selection level number and the salt indicator light both flash.
• Press button P to select the desired hardness level (see WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.

The setting is complete

• As soon as this procedure is complete, run a program without loading.
• Only use salt that has been specifically designed for dishwashers.
• After the salt has been poured into the machine, the SALT REFILL indicator light switches off.
• If the salt container is not filled, the water softener and the heating element may be damaged as a result of limescale accumulation.
• Using of Salt is recommended with any type of dishwasher detergent

FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be filled when the RINSE AID REFILL indicator light in the control panel is lit

1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow from the dispenser. If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press the button START/Pause three times – a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator light flash.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button

The setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.
The LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow the instructions above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device C. Introduce the detergent into the dry dispenser D only. Place the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent refer to the mentioned earlier information to add the proper quantity.
   Inside the dispenser D there are indications to help the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the closing device is secured in place.

The detergent dispenser automatically opens up at the right time according to the program.
If all-in-one detergents are used, we recommend using the TABLET button, because it adjusts the program so that the best washing and drying results are always achieved.
Usage of detergent not designed for dishwashers may cause malfunction or damage to the appliance.

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

• For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
• Pre-treatment of the dishes is not needed before any of the programs.
• Not all options can be used simultaneously.
• Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options, and sensor calibration. The sensor calibration can increase program duration up to 20 min

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1. ECO
   Eco program is suitable for cleaning normally soiled tableware, and for this use, it is the most efficient program in terms of its combined energy and water consumption, and it is used to assess compliance with the EU Ecodesign legislation.

2. 6th SENSE
   For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accordingly. When the sensor detects the soil level an animation appears in the display and the cycle duration is updated.

3. INTENSIVE
   Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).

4. FAST WASH&DRY
   Normally soiled crockery. Everyday cycle, that ensures optimal cleaning and drying performance in a shorter time.

5. CRYSTALS
   Program for delicate items, which are more sensitive to high temperatures, for example, glasses and cups.

6. RAPID 30’
   Program to be used for a half load of lightly-soiled dishes with no dried food residues. Does not include the drying phase.

7. SILENT
   Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.

8. SANITIZING
   Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform maintenance of the dishwasher.

9. PREWASH
   Use to refresh crockery planned to be washed later. No detergent is to be used with this program.

10. SELF-CLEAN
    Program to be used to perform maintenance of the dishwasher, to be carried out only when the dishwasher is EMPTY using specific detergents designed for dishwasher maintenance

Notes:
Please note that cycle Rapid 30’ is dedicated to lightly soiled dishes.

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.

MULTIZONE
If there are not many dishes to be washed, a half-loading may be used to save water, electricity, and detergent. Select the program and then press the MULTIZONE button: the indicator over the button lights up. By default, the appliance washes dishes in all racks.

To wash only the specific rack, press this button repeatedly:

• shown on the display (only the lower rack)
• shown on the display (only the upper rack)
• shown on the display (only cutlery rack)
• shown on the display (the option is OFF and the appliance will wash dishes in all racks).

Remember to load the upper or lower rack only, and to reduce the amount of detergent accordingly.
If the upper rack is removed, please apply detergent directly to the tub instead of the detergent dispenser.

TURBO

• This option can be used to reduce the duration of the main programs while maintaining the same washing and drying performance levels.
• After selecting the program, press the TURBO button, and the indicator light will switch on. To deselect the option, press the same button again.

KEYLOCK
A long press (for 3 seconds) of TURBO button, will activate the KEYLOCK function. The KEYLOCK function will block the control panel except the ON/OFF button. To deactivate the KEYLOCK, long press again

WATER TAP CLOSED – Alarm
Flashes when there is no inlet water or the water tap is closed.

POWER CLEAN®
Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles. Press this button to activate POWER CLEAN® (the indicator lights up).

TABLET (Tab)
This setting allows you to optimize the performance of the program according to the type of detergent used. Press the TABLET button (the indicator light will light up, the corresponding symbol will light up) if you use combined detergents in tablet form (rinse aid, salt, and detergent in 1 dose).
If you use powder or liquid detergent, this option should be off.

DELAY
The start of the program may be delayed for some time between 0:30 and 24 hours.

1. Select the program and any desired options. Press the DELAY button (repeatedly) to delay the start of the program. Adjustable from 0:30 to 24 hours. With each press of the button, the delay starts to increase by 0:30 if the selection is below 4 hours, 1:00 if the selection is below 12 hours, and 4 hours if the selection is above 12 hours. If 24 hours are reached, and the button is pressed, the delayed start is deactivated.
2. Press the START/PAUSE button: and the timer will begin counting down;
3. Once this time has elapsed, the indicator light switches off and the program begins automatically. If at the time of the countdown, the START/PAUSE button is pressed again the DELAY option is cancelled and the selected program starts automatically.
   The DELAY function cannot be set once a program has been started.

DRAIN OUT

To stop and cancel the active cycle, the Drain Out function can be used.
A long press of the START/PAUSE button will activate the DRAIN OUT function. The active program will be stopped and the water in the dishwasher will be drained out.

NaturalDry

NaturalDry is a convection drying system that automatically opens the door during/after the drying phase to ensure exceptional drying performance every day. The door opens at a temperature that is safe to your kitchen furniture, the door will not be opened when the option of TURBO is on.
As additional steam protection, specially designed protection foil is added together with the dishwasher (depending on the model type – can be the need to buy it). To see how to mount protection foil please refer to (INSTALLATION GUIDE).
NaturalDry functionality could be disabled by the user as follows:

• To DISABLE: Switch On, then switch Off. Keep the P button pressed for 5 sec., at the end of 5 sec the dishwasher plays a short beep. Switch On the machine, the display shows „oOF”.
• To ENABLE: Switch On, then switch Off the machine. Keep the P button pressed for 5 sec., at the end of 5 sec the dishwasher plays a short beep. Switch On the machine, the display shows „oOn”.

References

• Whirlpool Docs
• Register | Whirlpool Europe

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>