KLARSTEIN 10031556 Fireplace Heater User Manual

KLARSTEIN 10031556 Fireplace Heater

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

TECHNICAL DATA

PRODUCT DATA SHEET

only
Nominal heat output| Pnom| 2.0| kW|  | manual heat charge control, with integrated thermostat| N/A
Minimum heat output (indicative)| Pmin| 1.0| kW|  | manual heat charge control with room and/or outdoor temperature feedback| N/A
Maximum continuous heat output| Pmax,c| 2.0| kW|  | electronic heat charge control with room and/or outdoor temperature feedback| N/A
Auxiliary electricity consumption|  | fan assisted heat output| N/A
At nominal heat output (fan motor)| elmax| 0.014| kW|  | Type of heat output/room temperature control (select one)
At minimum heat output (fan motor)| elmin| 0.014| kW|  | single stage heat output and no room temperature control| no
In standby mode| elSB| 0.48| W|  | Two or more manual stages, no room temperature control| no
 |  | with mechanic thermostat room temperature control| no
 | with electronic room temperature control| no
 | electronic room temperature control plus day timer| no
 | electronic room temperature control plus week timer| yes
 | Other control options (multiple selections possible)
 | room temperature control, with presence detection| no
 | room temperature control, with open window detection| no
 | with distance control option| no
 | with adaptive start control| yes
 | with working time limitation| no
 | with black bulb sensor| no
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany|

SAFETY INSTRUCTIONS

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised.

• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
  CAUTION: Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given to be given where children and vulnerable people are present.

• If the appliance or the supply cord is damaged, it must be repaired by manufacturer, its service agent or qualified person.

• This heater must be used on an AC supply only and the voltage marked on the heater must correspond to the supply voltage.

• Do not switch the appliance on until it properly installed as described in this manual.

• The heater must not be located immediately below a socket outlet.

• The heater must not be located in front of a socket-outlet.

• Keep furniture, curtains and other fl ammable material at least 1 meter away from the appliance. Never closed to curtains and other combustible material, otherwise may cause risk

• Do not leave the appliance unattended during use.

• Do not leave the appliance unattended whilst connected to the mains supply.

• This appliance is intended for household use and should not be used for industrial purposes.

• From time to time, check the cord for damage. Never use the appliance if the cord or any part of the appliance shows signs of damage.

• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.

• Repairs to electrical appliances should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.

• Do not run the mains cable under carpets, rugs etc.

• Do not allow the mains cable to hang over sharp edges or come into contact with hot surfaces.

• In order to avoid overheating, do not cover or obstruct the heater in any way.

• Overheating will result if it is accidentally covered.

• Never immerse the product in water or any other liquids.

• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

• Do not use the appliance outdoors.

• Do not use if you have wet hands.

• Never use the appliance on or near hot surfaces.

• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cooled.

• Do not clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.

• Do not lift the appliance by the front panel.

• In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
  Note : This heater is not equipped with a device to control the room temperature. Don’t use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

INSTALLATION

Unpack the heater carefully and retain the packaging for possible future use.The heater are normally positioned against a wall. A choice of 1kW or 2kW heat output is provided by the heater, which is located at the bottom of the heater. Before connecting the heater check that the supply voltage is the same as that stated on the heater.
Note : Used in an environment where background noise is very low, it may be possible to hear a sound which is related to the operation of the flame effect. This is normal and should not be a cause for concern.

1. For optimum viewing, mark the top four screws fixing positions on wall in accordance with the recommend fixing dimensions- see Fig.2. Drill holes with a six drill bit.
2. Fix the wall bracket using that the plug and screws provided.
3. Carefully lift the heater up ensuring that the top rear ledge of heater engages the wall bracket (see Fig.2 in circle) and is sitting centrally.
4. Lift Softly Towards The Wall.
5. Mark the bottom holes position-see Fig.3, remove the heater ensuring that the bottom fixing bracket is rotated up.
6. Drill and fit wall plug.
7. Refit the heater to the wall fixing bracket and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place.
8. Place the front glass surround over the front of the fire aligning the slots in the brackets at each side of the glass panel with the lugs on the sides of the fire-see Fig.4. Again two people will be required for this operation.

GENERAL USE

Note : The appliance can be operated either by the switches located on the right hand side of the fire or by the supplied remote control.

Manual Operation

• This is done by operating the switches located on the right hand side of the fire. The standby rocker switch must first be switched on, the fire will beep to indicate that it is powered up.
• Press the O/I button once to turn on the appliance and fire effect. A red indicator light will show to indicate that the fire is ON. Press the O/I button for 3 seconds this will operate the dimmer mode, hold the button down until the desired brightness is obtained.
• Press once the 1000W button for the low heat settings; press twice to switch off the heat setting.
• Press once the 2000W button for the high heat settings; press twice to switch off the heat setting.

Remote Operation

The standby rocker switch located at the right hand side of the fire must first be switched on; the fire will beep to indicate that it is powered up. It takes a little time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for the fire to operate normally.

DISPLAY AND INDICATORS

1. Cursor
2. Date
3. Timer
4. Standby
5. Temperature display/ serial number display
6. Timer off
7. Timer on
8. Time display
9. Automatic control of heating
10. Flame brightness
11. Heat position

Temperature and serial number display (5)
Normally it displays the room temperature; while setting the temperature, the setting temperature is displayed; When setting the timer, the serial number of the setting is displayed.

Time display (8)
Normally it is display the current time; while setting the timer, the setting time is displayed.

Timer starting and timer shutdown
While setting the timer, the setting time is displayed, and the timer is used in combination with serial number setting.

Flame brightness
It displays the current brightness of the flame, which ranges from one to five positions.

OPERATION AND SETTINGS

Boot steps

1. Connect the power
2. Turn on the power switch
3. Press the control switch or „ON/OFF“ key of the remote controller to start up
4. Press once the1000W button for the low heat settings; press twice to switch off the heat setting.
5. Press once the 2000W button for the high heat settings; press twice to switch off the heat setting.
6. Press the DIMMER button for operate the dimmer mode.

Adaptive start control function
Press „IC“ button on the remote controller to start or close the adaptive start control function. When turned on this function, the fireplace can automatically change the heating mode, and this depends on the setting temperature and the room temperature. When the timer is on, it is possible to start the heating ahead of the schedule.
Note : Adaptive start control function is only working when the week timer system is power on.

The date and time setting

1. Press DATE-TIME button, then press the „▲ “ or „ ▼“ key to select the date
2. Press DATE-TIME button again, then press the „+“ or „-“ to set the hour
3. Press DATE-TIME button again, then press the „+“ or „-“ to set the minute
4. Press OK button to finish the setting.

Temperature setting
The default temperature setting is 22°C℃, press „+“ or „-“ on the remote controller to set the temperature, which ranges is from 15°C to 30°C.

TIMER SETTINGS

• There are up to 10 kinds of timer setting.
• Each setting has its date, power-on time, shutdown time and temperature setting
• The max. time of each setting is 23 hours 50 minutes
• The setting date for each timer can be any day or more days of a week
• The setting date is the date of power-on time. If the shutdown time is on the second day, it is unnecessary to set the date, you just set the shutdown time.

View the timer setting

1. Press the „TIME SET“ button.
2. Press the „+“ or „-“ to check the power-on time by one by one.
3. For checking the shutdown time, press the „ “ button.
4. Press the „+“ or „-“ to continue viewing.
5. For deleting the current item of setting, press „C“ to delete this setting.

Timer setting

1. Select the settings
   Press the „TIME SET“ button, and the serial number of setting starts blinking Press the „+“ or „-“ to change the serial number of the setting. E.g., it is showing the setting of No.2.

2. Select date
   Press „TIME SET“ button once again, and the cursor on the left side of date starts blinking Press the „ “ or “ ” keys to move the cursor to the corresponding date, press the „+“ to add the corresponding date, or press „-“ to delete the date until you have completed the selection of all dates

3. Set the start time

4. Continue to press the „TIME SET“ button, the hour starts blinking

5. Press the „+“ or „-“ to adjust the hour

6. Continue to press the „TIME SET“ button, the minute starts blinking

7. Press the „+“ or „-“ to adjust minute

8. Set the shutdown time

9. Press the „TIME SET“ button, the display is off, and the hour starts blinking.

10. Press the „+“ or „-“ to adjust the hour.

11. Continue to press the „TIME SET“ button, the minute starts blinking.

12. Press the „+“ or „-“ to adjust minute.

13. Set temperature
    Then press the „TIME SET“ button, and the temperature setting starts blinking. Then you can adjust the temperature by pressing „+“ or „-“. and “+” button will raise the temperature, and the “-” will lower the temperature. Press „TIME SET“ button to continue setting, and press „OK“ complete the setting.

Important Notes on Timer

• TIME ON/OFF is to control the timer opening and closing
• Note 1: Restart the machine after the power is cut off, the original setting is kept, but the date and time must be reset.
• Note 2: When the week timer is power on, you should turn on the heating function, or else when the machine is working again as the timer, there will be only the flame effect working.

Safety Cut-Off
This appliance is fitted with a safety cut-off which will operate if the fire overheats (e.g. due to blocked air vents). For safety reasons, the fire will NOT automatically reset. To reset the appliance, disconnect the appliance from the mains supply for at least 15 minutes. Reconnect to the mains supply and switch on the appliance.

Troubleshooting

Check for safety cut-off operation.
No fire effect light.| Check the bulb by a qualified electrician.

CARE AND CLEANING

Always disconnect from the mains supply before cleaning heater. For general cleaning use a soft clean duster – never use harsh abrasive or cleaners.
Note : The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners. This product does not use a standard bulb for its flame effect. The appliance uses an electronically controlled LED system to create the effect, therefore no parts need to be replaced. There are no user-serviceable parts on this appliance. Under no circumstances should the appliance be serviced be anyone other than a qualified electrician.

DISPOSAL CONSIDERATIONS
If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>