ecom-LSG Industry Leader in Combustion Instruction Manual
- May 15, 2024
- ECOM
Table of Contents
- ecom-LSG Industry Leader in Combustion Instruction Manual
- Intended Use
- Scope of Delivery
- General safety instructions
- Device Description
- Initiation
- Leak detection
- Zero Point
- Switch-off
- Settings
- Power Supply
- Functional Check
- Changing the Sensor
- Technical Data
- FAQ
- Maintenance
- Disposal
- Consumables/Spare Parts
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ecom-LSG Industry Leader in Combustion Instruction Manual
Intended Use
The ecom-LSG is developed for the detection of leaks in gas installations.
The unit shows existing gas concentration on the display and warns by means of
an optical and acoustic signal. The sensitivity of the sensor can be adjusted
so that even small leaks can be detected. The sensor head is connected to a
movable flexible tube, so that even parts of the installation which are
difficult to access can be reached.
Scope of Delivery
- ecom-LSG
- 2x 1.5 V AAA Batteries
General safety instructions
WARNING
Hazard of Injury
Improper work on gas pipes can result in injuries.
Work on gas pipes may only be carried out by qualified personnel.
When working on gas pipes, observe the applicable safety regulations.
CAUTION
Damage to the Sensor
Vibrations can damage the sensor head.
Avoid shocks to the sensor head.
CAUTION
Damage to the Sensor
Substances such as silicones, halogenated hydrocarbons, lead tetraethyl,
sulphur compounds and organic phosphorus compounds lead
to partially irreversible sensitivity losses.
Avoid contact with such substances.
NOTICE
Do not switch on ecom-LSG in air containing gas, as this will lead to
inaccurate measured values!
Device Description
1 | Flexible Tube | 3 | Display | 5 | On/Off |
---|---|---|---|---|---|
2 | Sensor Head | 4 | HOLD Key | 6 | LED |
Initiation
- Switch on the device.
NOTICE
Hold the On/Off key down until you hear a signal.
- Wait for the heating-up phase.
- 3-fold beeps indicate operational readiness.
-
- Display shows the gas concentration as a bar chart.
NOTICE
1 Bar = no concentration
14 Bars = max. concentration|
Leak detection
**** CAUTION
Damage to the Sensor
Substances such as silicones, halogenated hydrocarbons, lead tetraethyl,
sulphur compounds and organic phosphorus compounds lead to partially
irreversible sensitivity losses.
Avoid contact with such substances.
- Slowly move the sensor head past the gas installation to be tested.
- As soon as the ecom-LSG approaches a leak, the measured value display reacts.
NOTICE
If the first switching threshold is exceeded, the red LED flashes and an acoustic signal sounds. With increasing concentration, the LED flashes at shorter intervals and the signal tone becomes more intense
- The highest gas concentration registered so far is represented by a grey bar.
Zero Point
Deviations of the bargraph display from zero can be set to zero by pressing the HOLD key. The change of the zero point is indicated by flashing of the first bar. If the HOLD key is held down for more than 2 seconds, the original zero point is reset.
Switch-off
- Press and hold the ON/OFF key until no more bars are visible on the display.
Settings
Sensitivity
- With the machine switched on, press the On/Off key.
- Press the HOLD key.
-
* Small bars = low sensitivity
- Middle bars = medium sensitivity
- Large bars = high sensitivity
Battery Capacity/Setting Menu
-
With the machine switched on, press the On/Off key twice.
-
Battery capacity is displayed.
NOTICEIf 4 bars are shown on the display, the battery capacity is sufficient for about 1 hour.
-
Use the HOLD key to make the following settings:• Without lighting/without acoustic signal
• With lighting/without acoustic signal
• Without lighting/with acoustic signal
• With lighting/with acoustic signal -
- Press the ON/OFF key to save the selected setting and exit the menu.
Power Supply
The two 1.5 V AAA batteries must be replaced when a grey battery symbol appears in the top left-hand corner of the display. The remaining capacity is 1 hour. If the voltage drops further, the battery symbol turns black and the unit switches off automatically
Battery Change
- Open the battery compartment on the back.
- Remove old batteries.
- Insert new batteries.
-
- Close the battery compartment.
Functional Check
- Open the test medium bottle.
- Hold the sensor head over the opened test agent bottle.
NOTICE
The bar indicator should show a clear reaction, otherwise the sensor is defective and must be replaced.
Changing the Sensor
NOTICE
Switch off the device before replacing the sensor!
- Screw on the sensor head.
- Pull off sensor element.
- Install new sensor element.
- Screw on the sensor head.
Technical Data
Display Range | up to 0.5 % methane |
---|---|
Response Time | < 2s |
Display | Approx. 20 mm x 7 mm, bar chart |
Heating Period | Approx. 180 s |
Automatic Switch-off | After 30 min. |
Operation Temperature | -5 °C – 40 °C |
Storage Temperature | -25 °C – 40 °C |
Operation Moisture | 20 % – 80 % rF |
NOTICE
Subject to technical changes! (Status 11.2019)
FAQ
Bar 14 (calibration incorrect)
|
- A gas concentration was present during zero calibration.
- Too little difference between zero and 1000ppm calibration
- Sensor defective
---|---
Bar 11 (sensor head)|
- No sensor head available
- Sensor heating element defective
Maintenance
To ensure the accuracy of your measuring device, we recommend an annual inspection by an authorised ecom partner. In case of heavy use, shorter inspection intervals should be chosen – please contact your ecom partner.
Disposal
- Dispose of used batteries at the designated collection points.
- Dispose of packaging material in an environmentally friendly manner.
- Old devices must be disposed of in an environmentally friendly manner by an authorised centre.
NOTICE
On request we take back old appliances and dispose of them in an environmentally friendly way.
Consumables/Spare Parts
NOTICE
You can find consumables or spare parts in our webshop at www.shop.ecom.de.
ecom GmbH
Am Großen Teich 2
D-58640 Iserlohn
info@ecom.de
www.ecom.de
Phone: +49 2371 945-5
Fax: +49 2371 40305
Read More About This Manual & Download PDF:
References
- Messgeräte zur Abgasanalyse, Druckmessung & Lecksuche | ecom
- Gas Analysis | Instrumentation | Control | DRM Technic
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>