OASIS PWSBF Drinking Fountain VersaFiller Combo Installation Guide

Models:

• PWSBF
  • PWFSBF with VersaFilter III

The VersaFiller is an extension of the Aqua Pointe® product line that mounts directly above Versacooler® I and II products. No additional electrical connections are required.

If installed onto a refrigerated cooler, chilled water can be dispensed through the VersaFiller. Otherwise, room temperature water will be dispensed.

The VersaFiller is shipped partially assembled.

On the combo units, the cooler is plumbed and ready to attach to the VersaFiller.

When completed, the finished assembly will look like this:

Section 1: Getting Started

What’s Included:

Tools required:

• 3/8” pilot drill and either a step drill bit up to 7/8” diameter that will drill through SS top or 7/8” diameter punch die (retrofit version only)
• Electric drill; wrench for punch die
• Small tubing cutter for copper tube
• 1/4“ nut driver

• 2 Phillips screwdriver

• 15 torx bit driver

Section 2: Rough In Drawing

Oasis® PWSBF & PWFSBF: Versacooler® II Models PGAC, PG8AC, PGVAC, PGV8AC, PGACT, PG8ACT with Sports Bottle VersaFiller

Oasis® PWSBF & PWFSBF: Versacooler® II Split Level Models with Sports Bottle VersaFiller

On split level models, the VersaFiller must be mounted on the low unit in order to meet ADA guidelines.

Section 3A: Installation

Note: Proceed to Sect 3B Step 5 “Final steps for both product families” if the cooler is purchased “VersaFiller ready”.

A: Drilling hole in the top for water line connection.

1. Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
2. Turn OFF water supply to the unit. It might be necessary to remove the front panel to access the water stop valve.
3. Place hole template onto cooler top so it is aligned with the left side of unit and wall. SEE NEXT PAGE FOR TEMPLATE
4. Mark hole location
5. Remove top from unit.

6. Using a step drill bit or 7/8” punch die, make a 7/8” hole through top. You may want to drill a pilot hole to get these started.
7. Install snap bushing into hole to protect tubing from being cut.

USE THIS TEMPLATE TO MARK THE HOLE LOCATION ON COOLER TOP

Versacooler to Bottle Filler Plumbing Diagram

Two Versacoolers to Bottle Filler Plumbing Diagram

IMPORTANT: Flush filters before connecting water line to VersaCooler. PWFSBF only.
See steps 3-5 under Section 3D on page 16.

Section 3B: Installation

B: Connecting the water line

Note: If you are retrofitting the Versafiller to an existing cooler, follow the instructions starting on page 11.

For the single “Versafiller ready” cooler, the tube to connect to the Versafiller is found inside the access panel (the compressor compartment) or found inside the Bottle Filler. This tube supplies cold water from the cooling tank to the Versafiller.

The tee and tube to the Versafiller are packaged with the PWEBF unit. One branch of the tee will supply the valve on the dummy unit, the other branch of the tee will connect to the Versafiller.

If a filter is being installed, cut a piece of tubing about 3” long to insert (optional) flow switch right after filter and before tee. This allows Versafiller counter to accurately calculate amount of water passing through filter.

Go to Step 5 “Final steps for both product families:”

To retrofit the Versafiller to an existing unit, follow the instructions below:

If the cooling tank is non-pressurized, then go to the “Pressurizing the cooling tank” addendum section. Otherwise, proceed to step 1 below.
Non-pressurized units are single units made since December of 2009.
Refer to the schematic below to identify the system that you have.

1. With the cooler top removed, find the tube going from the cooling tank outlet to the valve. The TEE fitting (supplied) will need to connect between the cooling tank and valve.

Section 3B: Installation: For the P8AC Version: Versacooler II

Go to Step 5 “Final steps for both product families:”

Section 3B: Installation: For the P8AM Version: Versacooler I

Section 3B: Installation: Final steps for both product families:

5. Feed black and blue tubing up through bushing in top.
• For single unit, also feed white tube attached to tee through bushing.
• For split level, connect tee and white tube packed with bottle filler per schematic below.

Attach top to cooler.

Section 3C: Installation

C: Mounting the frame to the wall

1. Place rubber gasket on top of the cooler so it is centered left/right and against the wall.
2. Set the wall frame onto the gasket. Center it left/right and push it against the wall and mark hole locations for wall fasteners. The gasket will set the frame at the proper height.

3. Secure frame to the wall with fasteners (not provided). Pull plastic tubing up through the hole in the frame.

Section 3D: Installation

D: Installing and Flushing Filter Cartridge (PWFSBF only)

1. Insert filter cartridge, rotate ¼ turn until locked.
2. Route water supply plastic tube attached to filter head inlet (left side) through hole in fame and top. Connect to fountain water supply.
3. Route filter outlet tube that is attached to the filter head outlet (right side) to fountain drain in top. Flush filter cartridge before connecting to fountain cooling tank inlet fitting.
4. Turn ON the water supply and flush the filter for one-minute or until the water runs clear.
5. Connect the filter outlet tube to cooling tank inlet.

1. Slide sponge tubing insulation over water line. Connect the tubing to the INLET of the cartridge valve holder elbow fitting on the back of the VersaFiller assembly.

Section 3E: Installation

E: Attaching the Tether

2. Install bottle filler tether with the steps below.

3. The tether keeps the bottle filler secured to the frame when changing the filter. Make sure the tether is installed properly to avoid accidental damage to the unit.

4. Connect the tubing to the INLET elbow on the back of the VersaFiller assembly.

5. Set the VersaFiller cabinet into place. MAKE SURE the cabinet fits into the groove in the rubber gasket on both sides and front of the wrapper.

6. Attach VersaFiller assembly and top cap to the frame using the two (2) torx screws.

7. Turn ON water supply and check for leaks. Press the activation button and release any trapped air from the system. Plug in the power cord and replace the front panel IF it was removed earlier.

INSTALLATION COMPLETE

Addendum Section: Pressurizing Cooling Tank

Accessories:
Vandal resistant screw kit: P/N 036704-001, includes torx bits and replacement screws.
Gasket Adapter Elkay/Halsey Taylor P/N 041114-001

P/N 030099-682, Date: 04/2023

© 2023 LVD Acquisition, LLC

Oasis, Aqua Pointe, Versacooler and VersaFiller are registered trademarks of
LVD Acquisition, LLC dba Oasis International
Haws is a registered trademark of HAWS Corporation.
Elkay and Halsey Taylor are registered trademarks owned or licensed by Elkay
Sales Inc. and/or its parent Elkay Manufacturing Company

OASIS INTERNATIONAL

222 East Campus View Blvd.
Columbus, OH 43235
614-861-1350
www.oasiscoolers.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>