Air Oasis 1000G3 Air Purifier Owner’s Manual
- June 4, 2024
- Air Oasis
Table of Contents
Owner’s Manual
For use with models:
1000G3, 3000G3, 3000XG3,
AO1000G3-H, and
AO3000G3-H
1000G3 Air Purifier
This Manual Includes:
- Warranty
- Safety Warnings
- Operating Instructions
- Replacement Directions
- Troubleshooting Tips
- Cleaning and Maintenance Tips
Due to continuous improvements, the picture included within this owner’s manual may differ slightly from the actual product.
Before operating this unit carefully read the contents of this manual.
Read all instructions carefully before operating your air purifier.
Important Safety Instructions
When operating electrical appliances, basic precautions should always be followed.
WARNING
To reduce the risk of fire, electric shock, or injury:
- Do not use it outdoors or on wet surfaces.
- Use only as described in this manual.
- Do not use a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1-800-936-1764.
- Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
- Do not handle the plug or appliance with wet hands.
- Do not put any object into openings.
- Turn off all controls before unplugging.
CAUTION
AHPCO ® Cell contains Hg (Mercury) and should be disposed of according to
disposal laws. Find disposal centers at
www.earth911.org.
If the UV lamp is broken do not touch the cell or glass with your hands.
UV lamps may be hot and could cause serious burns if not handled properly.
Please wait until the AHPCO® Cell has cooled to room temperature to remove it
from the unit.
WARNING: UV Light Hazard. Harmful to skin and eyes. Can cause temporary
or permanent loss of vision. Never look at the lamp while illuminated. To
prevent exposure to ultraviolet light, be sure the power is disconnected
before servicing.
WARNING: RISK OF ELECTRICAL SHOCK. CAN CAUSE INJURY OR DEATH: UNPLUG OR
DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE SERVICING.
To view our warranty information, terms and conditions, and privacy policy, go to: https://www.airoasis.com/policies/#warranty-policy
Maintenance and Customer Service
If you require any additional information or have problems with your Air Oasis
appliance, you may call Air Oasis customer service at
1-800-936-1764
Please have your serial and model numbers, found on the bottom of the unit,
handy when calling.
Save your sales receipt to show if your Air Oasis appliance should ever need
any warranty service.
Placement and Operation
For best results, the unit should be placed in a central location and three
feet or higher from the ground.
The operation is very simple. Remove the Air Oasis from the packaging. Place
in the desired location, plug it in, and rock the switch to the on position.
The unit can remain in the on position 24/7.
Optional Cleaning
Make sure that the power cord is unplugged prior to cleaning.
Base and Honeycomb – We recommend wiping with a dry towel to remove dust
and build-up.
Aluminum Shell – We recommend using stainless steel/aluminum spray on
polish or multi-surface cleaners. Make sure the polish or cleaner is
recommended for use on aluminum.
Internal – Take a dry cloth and wipe inside the shell and around the
aluminum brackets and the ballast or spray with compressed air.
NOTE: Use compressed air only to clean AHPCO Cells. Any removal of
catalyst coating will decrease the effectiveness of your unit and void the
warranty.
Bi-Polar Brush Heads – The Bi-Polar brush heads inside your unit should
be cleaned periodically to remove any debris for optimal effectiveness. Just
lightly tap (flick) the brushes on brush head component.
AHPCO™ Cell Replacement
Step 1
CAUTION: Before attempting to service the Air Oasis unit, be sure the
power is off and unplugged.
DANGER – NEVER LOOK DIRECTLY AT ILLUMINATED AHPCO CELL
WARNING
OPTICAL RADIATION EXPOSURE HAZARD
DO NOT ATTEMPT TO OPERATE THE UNIT WITHOUT
ALUMINUM SHELL COVERING AHPCO CELL.
DO NOT ATTEMPT TO REPLACE AHPCO
CELL WITHOUT DISCONNECTING POWER.
PERMANENT EYE AND SKIN DAMAGE MAY RESULT.
-
Remove two (2) screws at the bottom sides holding an outer shell in place. Then slide the shell up and off of the internal base.
Step 2 -
Use a Phillips head screwdriver to remove the screws from the AHPCO ® Cell.
Step 3 -
Grasp the AHPCO® Cell and pull it to the side, then remove the lamp connector.
**CAUTION
UV lamps may be hot and could cause serious burns if not handled properly. Please wait until AHPCO® Cell has cooled to room temperature to remove it from the unit.
Step 4** -
Plug in the AHPCO® Cell, and slide the reset switch. Your unit will beep in 2 years when it is time to replace the AHPCO ® Cell.
Older models might have a reset button instead of a slide switch.
Step 5 -
Connect the lamp connector securely onto the AHPCO® Cell and use a Phillips head screwdriver to tighten the screws to secure the AHPCO ®Cell.
Step 6 -
Slide the shell down onto the base and replace the screws. (Cord and switch are to the back.)
Troubleshooting Guide
| Problem | Reason | Solution |
|---|---|---|
| The unit does not turn on. | 1. Power Supply |
2. Switch
3. AHPCO / Cell| 1. Check to make sure the power supply is plugged in.
2. Check to make sure the switch is in the on position.
3. Check to make sure the UV lamp within AHPCO ® Cell is plugged in
completely.
Single Beep Repeated Slowly.| The AHPCO® Cell has Expired.| Replace the AHPCO®
Cell.
The purifier doesn’t seem to be working to optimal efficiency.| The purifier
is being operated in areas with a high concentration of particulate matter.|
Refer to AHPCO Cell replacement Instructions to remove the shell. Use
compressed air or vacuum to remove dust & debris. remove dust & debris.
3401 Airway Blvd.
Amarillo, TX 79118
Toll-Free: 1-800-936-1764 Fax:
1-806-373-7799
www.airoasis.com
Copyright © 2021 Air Oasis, LLC. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>