milwaukee P36-WLAB Wireless Laser Alignment Base with Remote User Manual
- May 15, 2024
- Milwaukee
Table of Contents
milwaukee P36-WLAB Wireless Laser Alignment Base with Remote
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Read and understand all instructions. Failure to follow all instructions may result in electric shock, fire and/or serious personal injury. Save these instructions.
-
This tool is designed to be powered by AA batteries properly inserted into the tool. Do not attept to use with any other voltage or power supply.
Do not use zinc-carbon batteries. -
Chemical Burn Hazard. A new or used battery can cause severe in- ternal burns and lead to death in as little as 2 hours if swallowed or enters the body. Keep away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.
-
Do not mix new and used batteries. Do not mix brands (or types within brands) of batteries.
-
Do not mix rechargeable and non-rechargeable batteries.
-
Install batteries according to polarity (+ / –) diagrams. Do not install batteries backwards. Batteries can explode or leak.
-
Do not crush, drop, damage, or expose batteries to high temperature.
Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. -
Do not incinerate or dismantle batteries. Properly dispose of used batteries immediately.
-
For indoor use.
Federal Communications Commission
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules and ISED-Canada’s license exempt RSS standards. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
FUNCTIONAL DESCRIPTION
- Plumb point indent
- Rotating top plate
- Laser level adapter
- Motorized fixed base
- Height adjustable legs
- Fast sweep
- Single step/slow sweep
- Remote power button
- Power/movement LED
- Threaded 1/4″-20 tripod insert
- Power cell door
- Power button
- Power/movement LED
SPECIFICATIONS
Alignment Base Cat. No………………………………………………… 48-35-1314
Volts…………………………………………………………………………………..4.5V DC
Battery Type …………………………………………………………………..3x(AA) LR6
Module/FCC ID……………………………………………. RF4463PRO/P36-WLAB
Ingress Protection…………………………………………………………………….. IP54
Drop Rating …………………………………………………………………………….0.9 m
Working Range (Remote W/Base) ……………………………………………….125′
Adjustment Horizontal Range……………………………………………. 40′ @ 125′
Micro-Step Accuracy………………………………………………………3/32″ @ 100′
Mounting Thread …………………………………………………………………..1/4″-20
Remote Control Cat. No………………………………………………… 22-80-1314
Volts……………………………………………………………………………………..3V DC
Battery Type …………………………………………………………………..2x(AA) LR6
Module/FCC ID…………………………………………….RF4463PRO/P36-WLAR
Drop Rating ……………………………………………………………………………….3 m
Altitude………………………………………………………………………………….<6560′
Pollution Degree…………………………………………………………………………….2
Maximum Relative Humidity (RH) ………………………………………………. 80%
for up to 88°F
Decreasing Linearly Relative Humidity (RH) ………………………………… 50% at 104°F
Recommended Ambient
Storage Temperature………………………………………………..-13°F to 140°F
Operating Temperature……………………………………………….. 0°F to 122°F
SYMBOLOGY
- Volts
- Direct Current
- Read Operator’s Manual
ASSEMBLY
Attaching Laser to Alignment Base
The alignment base can be used with MILWAUKEE® M12™, MILWAUKEE® REDLITHIUM™ USB, and alkaline lasers.
-
To attach, align the grooves on the pivot bracket with the laser adapter features on the rotating top plate.
Slide the laser back until latched in place. -
To remove, carefully slide the pivot bracket on the laser out of the base of the mount.
Changing Batteries
Only use recommended batteries. If the tool will not be used for a long time,
remove the batteries as a protection against corrosion. Change batteries when
the base and/or remote light is red.
To change the batteries:
- Remove the laser from the wireless laser alignment base.
- Unscrew and lift latch to open battery door.
- Insert 3-AA batteries according to the +/- polarity marked in the compartment.
- Install the battery door and fasten securely.
OPERATION
Pairing Remote to Alignment Base
The remote control is not intended to be unpaired from the alignment base.
- If the remote becomes unpaired, hold the power button on remote control for 3 seconds, then hold power button on base for 3 seconds to repair.
Turning ON/OFF the Alignment Base
The alignment base can be used with MILWAUKEE ® M12™, MILWAUKEE® REDLITHIUM™
USB, and alkaline lasers. Ensure the align- ment base is powered on, and the
LED is solid green.
- To turn ON, press the power button, the LED will turn green. •To turn OFF, press the power button until the LED turns off completely.
Using the Remote Control
The remote control can only be used with one alignment base at a given time.
To avoid interference with other alignments bases on the same jobsite, space
out the tools from one another. The alignment base and remote control have
three modes; macro-sweep, micro-sweep, and micro-step.
- To turn ON, press the power button on the remote control.
- To adjust the alignment base, use the arrow buttons on the remote control: •To macro adjust, use the buttons with two triangles on it. This can be used in either left or right directions.
- To micro adjust, use the buttons with one triangle on it. This can be used in either left or right directions.
- To sweep, long hold the button, this can be done be with macro and micro buttons on the remote control.
- To turn OFF, press the power button until the LED turns off completely on the alignment base.
Low Battery for Alignment Base and Remote Control
The alignment base uses alkaline batteries, please see below instructions for
each LED status colors.
- For normal operation, the LED will be green, unless the remote control is unpaired, then the LED will be red.
- For low battery status, the LED will be solid red.
- If the batteries are depleted and the power button is pressed, the LED will pulse red for 1 second, then the alignment base will turn off.
MAINTENANCE
Cleaning
Clean dust and debris from vents. Keep tool clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to clean, since certain clean- ing
agents and solvents are harmful to plastics and other insulated parts.
Some of these include gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and household detergents contain- ing
ammonia. Never use flammable or combustible solvents around tools.
SERVICE – UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM – 6:30 PM CST or visit
www.milwaukeetool.com
Contact Corporate After Sales Service Technical Support with technical,
service/repair, or warranty questions.
Email:
metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE – CANADA
Milwaukee Tool (Canada) Ltd 1.877.948.2360
Monday-Friday, 7:00 AM – 4:30 PM CST or visit
www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
This MILWAUKEE power tool* is warranted to the original purchaser from an
authorized MILWAUKEE distributor only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace
any part on this power tool which, after examination, is determined by
MILWAUKEE to be defective in material or workmanship for a period of two (2)
years after the date of purchase unless otherwise noted. Return of the power
tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized
Service Station, freight prepaid and insured, is required.
A copy of the proof of purchase should be included with the return product.
This warranty does not apply to damage that MILWAUKEE determines to be from
repairs made or attempted by anyone other than MILWAUKEE authorized personnel,
misuse, alterations, abuse, normal wear and tear, lack of maintenance, or
accidents.
Normal Wear: Many power tools need periodic parts replacement and service to
achieve best performance. This warranty does not cover repair when normal use
has exhausted the life of a part including, but not limited to, chucks,
brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver
blades, pistons, strikers, lifters, and bumper cover washers
- This warranty does not cover battery packs or all power tools. Refer to the separate and distinct warranties available for those products.
The warranty period for the LED in the LED Work Light (49-24-0171) and the LED
Upgrade Bulb (49-81-0090) is the lifetime of the product subject to the
limitations above. If during normal use the LED or LED Upgrade Bulb fails, the
part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable warranty on a
MILWAUKEE power tool product. The manufacturing date of the product will be
used to determine the warranty period if no proof of purchase is provided at
the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN
IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF
YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO
EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPE- CIAL, CONSEQUENTIAL,
OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR
DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT
IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY
IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of
MILWAUKEE’s website www.milwaukeetool.com or
call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility
for warranty and non-warranty service on a MILWAUKEE power tool.
References
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>