Y H BL912 Auto Focus Tracking Solar Panel Charge Controller Regulator Instruction Manual
- March 22, 2024
- Y H
Table of Contents
BL912 Auto Focus Tracking Solar
Panel Charge Controller Regulator
Instruction Manual BL912 Controller wiring tutorial
BL912 Auto Focus Tracking Solar Panel Charge Controller Regulator
HOW TO WIRE YOUR SOLAR CONTROLLER?
- (Controller terminal side)Turn the adjusting screw counterclockwise until the plate inside terminal moves downward.
- (wire)Please peel off the coating of the cable tip by about 8 to 10 mm
- Insert the wire into the new opening between the plate and the “top” of the terminal hole.
- When turning the adjuster clockwise, the plate moves upward and crushes the wire in the hole of the terminal.
- Make sure all connections going into and from the solar controller are tight.
Note: This solar controller charging is from high voltage to low voltage, please make sure solar panel voltage is higher than battery voltage, otherwise it cannot be charged.
Connecting solar panels
| Model | 12V Battery | 24V Battery | |
|---|---|---|---|
| Maximum Solar Power (W) | 40A | <520W | <1040W |
| 0A | <720W | <1440W | |
| 100A | 1200W | <2400W | |
| Solar Voltage Range (VOC) | 15V-23V | 30V-45V |
**For safety reasons, connect solar panels and batteries within the recommended range.
Tip: After connecting the battery, the controller will automatically detect 12V/24V DC system voltage, the system defaults to lead-acid battery, if it is other types of batteries, you need to set the charging cut-off voltage.
Connect the load, the load interface can only be connected to the LED lights
LED lamp voltage value:
| Model (BL912) | Connecting a 12V Battery | Connecting a 24V Battery |
|---|---|---|
| Load Voltage(V) | 12V LED | 24V LED |
LED lights use power:
| | 40A| 60A| 100A
---|---|---|---|---
Load powe ( W)| 12V Battery| <336W| <504W| <MOW
24V Battery| <672W| <1008W| <1680W
Load power should generally leave a 30% margin.
Example: 12V battery 100A controller, formula: 12V x 100A x 70% = load maximum
power (W)
Because the battery voltage is floating, LED lights at different voltages will
not be the same brightness.
Example: 12v lithium battery to 12v bulb power supply, lithium battery is full
of 12.8v, this time the LED lights will be brighter, when the battery work
discharge voltage drop, the voltage value is lower than 12v or 11v, the light
bulb will gradually become dark. When the battery power is too low, the bulb
may flicker or go out directly. This time indicates that the battery power is
low.
When Wiring, Please
- Make sure your battery must be at least 60% charged prior to connecting to solar controller.
- Always connect and turn on your battery first! Wire your PV after LCD screen power on.
- Never connect your PV array to the solar controller when LCD OFF.
- Careful your input power and voltage does not exceed the solar controller’s max value.
- Always connect battery first, then solar panel.
Important: During the operation of the controller, heat will be generated at
the wiring terminal, incorrect wiring will cause safety hazards.
DO NOT
- Don’t put wire under the terminal’s plate.
- Don’t Put two or more wire in one terminal, each terminal only accept one.
- Don’t exposed copper outside the terminal; (The exposed copper wire needs to be tightly and completely connected to the terminal.)
- The wiring must be tight and not loose.
Shenzhen Yonghui Fashion Co., Ltd
WhatsApp: +86 13750091547 Emai l:
barley@yonghuisolar.com
web: _https://www.yonghuisolar.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>