tp-link MCRP100 Redundant Power Supply Module Installation Guide
- May 15, 2024
- tp-link
Table of Contents
tp-link MCRP100 Redundant Power Supply Module
For technical support and other information, please visit https://www.tp- link.com/support, or simply scan the QR code
Panel Layout
LED Explanation
Installation
Remove the protective cover on the power supply module slot of MC1400. Then gently push in the module and plug it solidly into the connector.
Power On
Plug the negative connector of the AC power cord into the power socket of
MCRP100, and the positive connector into a power outlet as the following
figure shows. After MCRP100 is powered on normally, the Power LED and FAN LED
indicators on its front panel will keep on.
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
- The label is placed on the bottom surface of the product.
- Place the device with its bottom surface downward.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- Plug the product into the wall outlets with earthing connection through the power supply cord or plug.
- In Denmark : Apparatets stikprop skal tilsluttes en stikkontakt med jord som giver forbindelse til stikproppens jord.
- In Finland: Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
- In Norway : Apparatet må tilkoples jordet stikkontakt
- In Sweden: Apparaten skall anslutas till jordat uttag
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
FCC compliance information statement
- Product Name : 100-240V Redundant Power Supply Module
- Model Number : MCRP100
- Responsible party :
TP-Link USA Corporation
- Address: 10 Mauchly, Irvine, CA 92618
- Website: https://www.tp-link.com/us/
- Tel: +1 626 333 0234
- Fax: +1 909 527 6804
- E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
EU Declaration of Conformity
TP-Link hereby declares that the device complies with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863. The original EU
Declaration of Conformity may be found at
UK Declaration of Conformity
TP-Link hereby declares that the device complies with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016. The original UK Declaration of Conformity may be found at
Explanation of the symbols on the product label
Symbols may vary from products . The label is at the bottom of the product.
Specifications
- Product Name: 100-240V Redundant Power Supply Module
- Model Number : MCRP100
- Input Voltage : 100-240V AC, 50/60Hz, 2.5A
- Compatibility: TP-Link MC1400 and TP-Link FC1420
FAQ
Q: What are the safety precautions for operating the device?
A: Please read and follow the safety information provided in the manual to avoid accidents or damage due to improper use. Operate the device with care and at your own risk.
Q: What are the FCC compliance details for the product?
A: The product complies with part 15 of the FCC Rules. Any changes or
modifications not approved by the responsible party could void the user’s
authority to operate the equipment.
Q: Where can I find the EU Declaration of Conformity for the product?
A: The EU Declaration of Conformity can be found at https://www.tp-
link.com/en/ce.
References
- Link: Simple, secure one-click payments
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
- WiFi Networking Equipment for Home & Business | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>