EAW AC6 Subwoofer Stack Plate Kit Instruction Manual
- May 15, 2024
- EAW
Table of Contents
AC6 Stacking Plate Instructions
Available Parts (NOTE: These are not part of a kit)
AC6 Subwoofer Stack Plate Kit
Part # | Part Name | Quantity | Reference |
---|---|---|---|
2071927-9999 | PLATE LOCKING ASSY | 1 | A |
2071924 | M5X20 FLH SKT SS BLK – Use w/Reference A | 3 per assembly | B |
2071924 | M5X20 FLH SKT SS BLK | 4 per plate | B |
2071918-9999 | Slide Plate | 2 | C |
2071929-9999 | MOUNT PLATE ASSY AC6 | 1 | D |
2072271-9999 | OTTO Plate ASSY | 1 | E |
2071920 | SCREW M20X40 HHCS SS BLK OX | 1 | F |
2072284 | M20 X 90 Hex Bolt | 1 | G |
2071922 | WASHER CURVED LOCK M20X34mm | 1 | H |
2071923 | WASHER FLAT M20 X 60mm OD SS BLK OX | 1 | I |
22095 | SCREW M6 X 55 SHCS BLK | 4 per assembly | J |
105059 | WASHER SPLIT-LOCK M6 SS BLK | 4 per assembly | K |
2071921 | WASHER FLAT M6 X18mm OD SS BLK OX | 4 per assembly | L |
Required Tools & Supplies
- M3 Allen Wrench
- M4 Allen Wrench
- 30mm Wrench
Prepare AC6 for Stacking
-
Attach Locking Plate (A) to the top of the first AC6 (If using with subwoofer mount plate, follow instructions in step 2 to attach slide plate to bottom of first AC6)
• Remove 3x M5x12mm screws from top of AC6 (Figure 1).
• Position Locking Plate over open holes, then use screws (B) to secure plate to the cabinet (Figure 2)
-
Attach slide plate (C) to bottom of next AC6
• Remove 4x M5x12mm screws from bottom of AC6 (Figure 3).
• Position Slide Plate over open holes, then use screws (B) to secure plate to the cabinet (Figure 4)
Prepare Subwoofer Mount Plate for Stacking (if applicable) -
Attach Mount Plate (D) to the top of SBX218/SBX118/RSX18F (Figure 5)
• Remove M6x35mm screws from subwoofer pole mount.
• Place Mount Plate on top of subwoofer, aligning hole A with pole cup.
• Lock into place with M6 screws (J), lock washer (K) and flat washer (L)
• Secure mount with M20x40 Screw (F), lock washer (H) and flat washer (I)
• If using older pole cup design for SBX118 & SBX218, M20x90 screw (G) will need to be used in place of M20x40 (F)
• Alternately, K&M Pole Adapter Bolt #245026 may be used with M20x40 screw (G) instead of using M20x90 screw (G)
-
Attach OTTO Mount Plate (E) to the top of OTTO subwoofer (Figure 7)
• No additional mounting hardware is needed than plate (E)
• Position mounting plate on top of OTTO and lock into place using 2x OTTO rigging pins.
Configure AC6 Column on Subwoofer or OTTO Mount Plate
-
Attach first AC6 to Subwoofer with mount plate
• Using two people, lift AC6 and line up bottom slide plate with subwoofer mount plate
• Slide into place (Figure 9). An audible clicking sound may be heard if pins are not in up position.
• On rear of mount plate, rotate both pin knobs clockwise to lock into position.
Connect two AC6 Column loudspeakers with stacking plates -
Attach two AC6 columns (Procedure is the same whether using Subwoofer Mounting Plate or not)
• Ensure first AC6 (bottom position) is standing flat on a surface or locked into place with the subwoofer mounting plate.
• If connecting a second AC6 on a subwoofer stack, using two steady ladders and two people, lift second AC6 and line up slide plate with the first AC6 locking plate.
• If connecting the second AC6 to first AC6 without utilizing the subwoofer mount plate, a ladder may not be needed. Still using two people, position second AC6 slide plate to line up with first AC6 locking plate.
• Slowly slide into plate until an audible click is heard. (Figure 11)
• On rear of first AC6 locking plate, rotate both screw knobs clockwise to lock into position.
• When using subwoofer mounting plate, only two AC6’s are supported.
Tel 800 992 5013
+1 508 234 6158
www.eaw.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>