BONDLINE SRM100 Surface Resistivity Meter and Kit Instruction Manual
- May 15, 2024
- BONDLINE
Table of Contents
BONDLINE SRM100 Surface Resistivity Meter and Kit
Introduction
- Thank you for purchasing a Surface Resistance Meter/Kit. Please read this instruction manual in great detail before operating the device.
- Keep this manual readily accessible for later reference.
Description
- This unique meter is extremely accurate and indicates resistance to ‘half a decade’ through the important static dissipative range using 10/100-volt test voltages to ensure more accurate readings.
- The SRM 100/K has been designed specifically for testing surfaces used in an EPA. It measures in Ohms per Square and meets the requirements of IEC 61340-5 and EN100 015/1 European standard.
- Automatic auto-ranging 1 0v and 1 00v test voltages are incorporated into the tester, switching as you move from conductive, dissipative, and insulative surfaces.
- The SRM100/K is also capable of testing resistance-to-ground and point-to-point resistance. Custom logos and printing can be quoted on request. Manufactured in the United Kingdom.
SRM1 00K Packing List
Make sure each of the following items is included in the kit.
- SRM 100 meter ……………………………………………………………………………………………………………………………. ..
- Two weights (2.5 kg / 5 lb) ……………………………………………………………………………………………………………. .
- All required test leads ………………………………………………………………………………………………………………….. .
- 9V battery . …………………………………………………………………………………………………………………………………… .
- Conductive foam discs …………………………………………………………………………………………………………………. .
- Conductive carry case ………………………………………………………………………………………………………………….. .
- Instruction manual ………………………………………………………………………………………………………………………. .
- Calibration certificate …………………………………………………………………………………………………………………….
Specifications
Method of Measurement| Surface Resistivity| (0| per square) Point-to-
point| (0)
---|---|---|---|---
Indicators| Conductive – Green LED – 1KO (1QA3) to 100KO (1QAS)
Dissipative – Yellow LED – 300KO (3 x 1QAS) to 1 GO (10A9)
Conductive – Green LED – 3GO (3 x 10A9) to 10GO (1OA10) insulative – Red LED – 100GO (10A11) to no (1OA12)
Relative Humidity| 0% to 90% (non-condensing)
Accuracy| +/- 0.5 Decade in Conductive Range
+/- 0.25 Decade in Dissipative Range
Test Range| 1KO (10A3) to 1TO (1OA12)
Displayed in 1 /2 Decade Steps
Temperature Range| Operating S°C to 49°C (40°F to 120°F) Storage – 1S°C
to +60°C
Repeatability| +/- 10%
Weight| 150g
Dimensions| 130mm x 70mm x 25mm
Calibration| Every 12 months by manufacturer
Test Voltage| Nominal 9 volts-stepped to 100 volts
Power Supply| 9 volt PP3 alkaline battery
User Guide
- Testing and auditing all elements within the EPA is essential to comply with industry standards. All test instruments are manufactured to the very highest quality allowing qualification to council directives 89/336/EEC.
- The SRM100/K has been designed specifically for testing surfaces used in EPA measures in Ohms per Square and meets the requirements of I EC 61340-5-1 /2 and EN 100015/1 European standard.
- Automatic auto-ranging 1 0v and 1 00v test voltages are incorporated into the tester, switching as you move from conductive, dissipative, and insulative surfaces.
- The SRM100/K is also capable of testing resistance-to-ground and point-to-point resistance.
Setup and Operation
- Fit the supplied 9V battery; the battery compartment is located at the rear of the enclosure. The unit is now ready to use. If at any time the battery voltage drops below 6.5 volts, the blue battery low indicator will light.
- To test surface resistance, place the unit on the surface to be tested and press the test button.
- To measure resistance-to-ground, insert one of the supplied test leads into one of the two 3.5mm sockets, located on the top panel of the meter, attaching the other end to your ground point. Press the test button.
- SRM100K ONLY- To measure the point-to-point resistance, insert the 3.5mm Jack plug test leads into the 2 x 3.5mm Jack sockets located on the top panel of the meter. Connect the two 2.5kg (51 b) weights to the other end of the test leads via the 4mm banana plugs (Red & Black). Place the weights gently onto the surface that requires testing. Press the test button. The resistance of the surface under test will be displayed in Ohms.
- GREEN LEDs indicate a conductive reading. Measurements are taken at a test voltage of 1 OV.
- YELLOW/ ORANGE LEDs indicate a dissipative reading. Measurements are taken automatically at a test voltage of 100 volts.
- RED LEDs indicate an insulative reading. Measurements are taken automatically at a test voltage of 100 volts.
- sales@bondline.co.uk
- www.bondIine.co.uk
- +44 (0)1793 511000
- The information contained within this instruction manual is for guidance only.
- We make no warranties expressed or implied and assume no liability regarding any use of this information. (Review February 28th, 2024)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>