BONDLINE SRM100 Surface Resistivity Kit Instruction Manual
- June 13, 2024
- BONDLINE
Table of Contents
**BONDLINE SRM100 Surface Resistivity Kit Instruction Manual
**
Description
This unique kit is extremely accurate and indicates resistance to ‘half a decade’ through the important static dissipative range using 10/100 volt test voltages to ensure more accurate readings. The SRM100 has been designed specifically for the purpose of testing surfaces used in an EPA. It measures in Ohms per Square and meets the requirements of IEC 61340-5 and EN100 015/1 European standard. Automatic auto ranging 10v and 100v test voltages are incorporated into the tester, switching as you move from conductive, dissipative and insulative surfaces. The SRM100 is also capable of testing resistance to ground and point to point resistance. Custom logos and printing can be quoted on request. Manufactured in the United Kingdom.
Supplied With:
- SRM100 meter.
- Conductive foam discs.
- Two weights (2.5 kg / 5 lb).
SRM100K – Kit
(Supplied in a conductive carry case)
- All required test leads.
- 9V battery.
- Conductive euro box for easy storage.
SRM100
(Surface Resistivity Meter)
Specifications
Method of Measurement| Surface Resistivity (Cl per square) Point to
point (Cl).
---|---
Indicators| Conductive – Green LED 1KCI (10A3) to 100KC1
(10A5).Dissipative – Yellow LED3001(12 (3 x 10A5) to 1GC2(10A9).Conductive –
Green LED3GC2 (3 x 10A9) to 10GO (10A10).Insulative – Red LED100GC1 (10A1
1)to1TC2(10/12).
Relative Humidity| 0% to 90% (non-condensing).
Accuracy| +/- 0.5 Decade in Conductive Range. +/- 0.25 Decade in
Dissipative Range.
Test Range| 1KCI (10A3) to 1TCI(10Al2). Displayed in 1/2 Decade Steps.
Temperature Range| Operating 5°C to 49°C (40°F to 120°F). Storage – 15°C
to +60°C.
Repeatability| +/- 10%.
Weight| 150g.
Dimensions| 130mm x 70mm x 25mm.
Calibration| Every 12 months by manufacturer.
Test Voltage| Nominal 9 volts-stepped to 100 volts.
Power Supply| 9 volt PP3 alkaline battery.
User Guide
Testing and auditing all elements within the EPA is essential to comply with industry standards. The SRM100 has been designed specifically for the purpose of testing surfaces used in an EPA and measures in Ohms per Square and meets the requirements of IEC 61340-5-1/2 and EN100015/1 European standard.
Automatic auto ranging 10v and 100v test voltages are incorporated into the tester, switching as you move from conductive, dissipative and insulative surfaces. The SRM100 is also capable of testing resistance to ground and point to point resistance.
Set-up and Operation
- Fit the supplied 9V battery; the battery compartment is located at the rear of the enclosure. The unit is now ready to use. If at any time the battery voltage drops below 6.5 volts the blue battery low indicator will not illuminate during the test.
- To test surface resistance, place the unit on the surface to be tested and press the test button.
- To measure resistance to ground, insert one of the supplied test leads into one of the two 3.5mm sockets, located on the top panel of the meter, attaching the other end to your ground point. Press the test button.
- SRM100K ONLY- To measure the point to point resistance, insert the 3.5mm Jack plug test leads into the 2 x 3.5mm Jack sockets located on the top panel of the meter. Connect the two 2.5kg (51b) weights, to the other end of the test leads via the 4mm banana plugs (Red & Black). Place the weights gently onto the surface that requires testing. Press the test button.
- GREEN LEDs indicate a conductive reading. Measurements are taken at a test voltage of 10V.
YELLOW / ORANGE LEDs indicate a dissipative reading. Measurements are taken automatically at a test voltage of 100 volts.
RED LEDs indicate an insulative reading. Measurements are taken automatically at a test voltage of 100 volts.
Registered at Cardiff No. 2933918
Registered Office: Bondline Electronics, Unit 4, Rivermead Industrial
Estate,
Rivermead Drive, Swindon, Wiltshire, SN5 7EX
- Email: [email protected]
- www.bondline.co.uk
- Tel: +44(0) 1793 511000