DFI KS101-EHL 10.1 Inch Industrial Touch Panel PC Installation Guide

DFI KS101-EHL 10.1 Inch Industrial Touch Panel PC

Specifications

• Model: KS101-EHL
• Type: Industrial Touch Panel PC
• Display: 10.1″ Touchscreen
• Connectivity: VGA, USB 3.1 Gen2, LAN, Line-Out, DC-In, COM Ports
• Additional Features: Power Button, DP++, USB 2.0

Product Usage Instructions

Removing the Chassis Cover

1. Ensure the system and all peripheral devices are powered off.
2. Disconnect all power cords and cables.
3. Remove the 8 screws securing the cover to the chassis and keep them safe.
4. Lift the cover to open the system.

Installing an M.2 Card

1. Insert the card into the socket at an angle, aligning the notch and key properly.
2. Press the end of the card far from the socket down until it touches the stand-off.
3. Screw tight the card onto the stand-off using a screwdriver until the card lies parallel to the board

Installing an Antenna

1. Ensure the PC and all connected devices are powered down.
2. Disconnect all power cords and cables.
3. Remove the rubber plug covering the antenna hole on the right side of the system.
4. Connect the internal cable to the board’s antenna connector and screw on the antenna through the antenna hole using washers and nuts.

FAQ

Q: Where can I find more documentation and drivers for KS101-EHL?

A: For more documentation and drivers, visit the download page at www.dfi.com/downloadcenter or scan the QR codes provided on the product.

KS101-EHL
10.1″ Industrial Touch Panel PC

www.dfi.com

Package Contents

• 1 x KS101-EHL System Unit
• 1 Poron Foam
• 1 Quick Installation Guide

Product Overview

1. VGA
2. USB 3.1 Gen2
3. LAN
4. Line-Out
5. DC-In
6. COM Ports
7. Power Button
8. DP++

1. USB 2.0

Removing the Chassis Cover

Please observe the following guidelines and follow the instructions to open the system.

1. Make sure the system and all other peripheral devices connected to it have been powered off.
2. Disconnect all power cords and cables.

Step 1:
The 8 screws of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use.

Step 2:
Lift the cover to open the system.

Installing an M.2 Card

Please follow the steps below to install the card into the socket.

Step 1:
Please follow the steps below to install the card into the socket. Insert the card into the socket at an angle while making sure the notch and key are perfectly aligned.

Step 2:
Press the end of the card far from the socket down until against the stand- off.

Step 3:
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted.

Installing an Antenna

Before installing the antenna, please make sure that the following safety cautions are wellattended.

1. Make sure the PC and all other peripheral devices connected to it has been powered down.
2. Disconnect all power cords and cables.

Step 1:
There are antenna holes reserved on the right side of the system and by default covered by rubber plugs. Please remove the plug prior to installing an antenna.

Step 2:
Connect the internal cable to the board’s antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below.

DFI reserves the right to change the specifications at any time prior to the product’s release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/downloadcenter, or via the QR codes to the right.

Quick Installation Guide | KS101-EHL

References

• DFI | Embedded Motherboard | Industrial Computer
• DFI | Embedded Motherboard | Industrial Computer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>