DFI VP070-M8M ARM Based In Vehicle Fanless Touch Panel PC Installation Guide

June 12, 2024
DFI

DFI VP070-M8M ARM Based In Vehicle Fanless Touch Panel PC

Product Information

Product Name VP070-M8M
Product Type ARM-Based In-vehicle Fanless Touch Panel PC
Manufacturer DFI
Website www.dfi.com

Package Contents

  • 1x VP070-M8M System Unit
  • 1 Switch Cable
  • 12 Rubber Holders
  • 1 ADDM UL Battery Addendum

Product Overview

Bottom ViewDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(1\)

  1. USB 3.1 Gen1

  2. LAN

  3. SIM

  4. Power Input

  5. Status LED

  6. Reset Switch

  7. OTG
    Back ViewDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(2\)

  8. COM

  9. CANbus

Removing the Chassis Cover

Please observe the following guidelines and follow the instructions to open the system.

  1. Make sure the system and all other peripheral devices connected to it have been powered off.
  2. Disconnect all power cords and cables.

Step 1:
The 8 screws of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use.DFI-VP070-M8M-ARM-
Based-In-Vehicle-Fanless-Touch-Panel-PC- \(3\)

Step 2:
Slide the cover to open the system.DFI-VP070-M8M-ARM-Based-In-Vehicle-
Fanless-Touch-Panel-PC- \(4\)

Step 3:
The boards can be easily accessed after the chassis cover is removed.DFI-
VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(5\)

Installing an M.2 Card

DFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(6\)

Please follow the steps below to install the card into the socket.

Step 1:
Please follow the steps below to install the card into the socket. Insert the card into the socket at an angle while making sure the notch and key are perfectly aligned.

Step 2:
Press the end of the card far from the socket down until against the stand- off.

Step 3:
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted.

Installing an Antenna

Before installing the antenna, please make sure that the following safety cautions are wellattended.

  1. Make sure the PC and all other peripheral devices connected to it has been powered down.
  2. Disconnect all power cords and cables.

Step 1:
There are antenna holes reserved on the right side of the system and by default covered by rubber plugs. Please remove the plug prior to installing an antenna.

Step 2:
Connect the internal cable to the board’s antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below.

System Layout

Power BoardDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(12\)

  1. ST-Link / SWD
  2. MCU Debug
  3. Remote Switch
  4. Remote Switch High/Low Active
  5. 12V DC Out
  6. 9V~36V In
  7. Host Bus Communication
  8. Host Bus Communication
  9. SW1
  10. LED1(Red): Debug LED for the MCU
  11. LED2 (Green): R/W LED

System BoardDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(14\)

  1. USB2_4
  2. HDMI
  3. Battery
  4. Power Link
  5. SIM Slot
  6. LAN
  7. USB3.0
  8. DC-IN
  9. Audio
  10. DIO
  11. Speaker
  12. USB2_3
  13. VP IO
  14. COM1 Debug
  15. Boot CFG
  16. LVDS
  17. I2C
  18. LED Backlight

System Board – uSD Card SlotDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-
Touch-Panel-PC- \(16\)

Jumper Settings

Jumper Settings- Power Board

DFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-Touch-Panel-PC-
\(17\)

Jumper Settings- Power BoardDFI-VP070-M8M-ARM-Based-In-Vehicle-Fanless-
Touch-Panel-PC- \(19\)

DFI reserves the right to change the specifications at any time prior to the product’s release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/downloadcenter, or via the QR codes to the right.

www.dfi.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals