DFI EC900-8MM Industrial Computers Installation Guide

June 10, 2024
DFI

EC900-8MM Industrial Computers

DFI EC900-8MM-Industrial-Computers-01

Product Information: EC900-8MM / EC910-8MM

The EC900-8MM and EC910-8MM are compact industrial computers designed for various applications. They are equipped with LAN, USB, HDMI, COM, and digital I/O ports for connectivity. The systems feature a DIN-rail mount chassis for easy installation and an antenna hole for wireless communication. The systems also support M.2 cards for storage expansion.

Package Contents:

  • 1 EC900-8MM/EC910-8MM system unit

Ports and Components:
The following ports and components are available on the systems:

Port/Component Description
LAN 1 & LAN 2 2 Gigabit Ethernet ports
COM (RS485) 1 RS485 port
A terminal block 1 RS422 (4-pin) port, 1 Digital IO (4-pin) port, 1 Power

(1-pin) port, and 1 Ground (1-pin) port
USB 2.0| 2 USB 2.0 ports
HDMI| 1 HDMI port
Status LED| 1 LED for system status indication
DIN-rail Mount| 1 DIN-rail mount bracket
Antenna Hole| 1 antenna hole for wireless communication

Jumper Settings:
The jumper settings for the X IOJP1 port are as follows:

Jumper Setting Description
2-4 On VCCP 5V (Default)
3-5 On DIO 5V (Default)
1-3 On DIO 3V3 (Default)
2-4 On VCCP 3V3 (Default)

Product Usage Instructions:

Removing the Chassis Cover:
To remove the chassis cover, follow these steps:

  1. Make sure the system and all other peripheral devices connected to it have been powered off.
  2. Disconnect all power cords and cables.
  3. Remove the 2 screws on the both sides of the system that secure the cover to the chassis and put them in a safe place for later use.
  4. Slide the cover to open the system.

Installing an M.2 Card:
To install an M.2 card, follow these steps:

  1. Insert the card into the socket at an angle while making sure the notch and key are perfectly aligned.
  2. Press the end of the card far from the socket down until against the stand-off.
  3. Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted.

Installing an Antenna:
To install an antenna, follow these steps:

  1. Make sure the PC and all other peripheral devices connected to it has been powered down.
  2. Disconnect all power cords and cables.
  3. Remove the rubber plug covering the antenna hole on the right side of the system.
  4. Connect the internal cable to the board’s antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated in the manual.

Mounting Options:
To mount the system using DIN-rail mount, follow these steps:

  1. Use the provided mounting screws to attach the DIN-rail mount bracket to the top side of the system.
  2. Install the system onto the rail.

EC900-8MM / EC910-8MM

DFI EC900-8MM-Industrial-Computers-01

Package Contents

  • 1 System unit
  • 1 10-Pole Terminal Block for RS-422/4-bit DIO
  • 1 2-Pole Terminal Block for RS-485
  • 2-Pole Terminal Block for Power Input
  • DIN Rail Bracket/Screw Pack
  • Quick Installation Guide

Product Overview

EC900-8MM

Front View

DFI EC900-8MM-Industrial-Computers-02

Left View DFI EC900-8MM-Industrial-Computers-03

  1. LAN 1 & LAN

  2. USB 2.0

  3. HDMI

  4. COM (RS485)

  5. Reset Button

  6. Status LED

  7. A terminal block:
    RS422 (4-pin)
    Digital IO (4-pin)
    Power (1-pin)
    Ground (1-pin)

  8. DC IN

Rear View

DFI EC900-8MM-Industrial-Computers-04

DIN-rail Mount

Right ViewDFI EC900-8MM-Industrial-Computers-05

Antenna Hole

EC910-8MM
Front View DFI EC900-8MM-Industrial-Computers-06

Left View
DFI EC900-8MM-Industrial-Computers-07

  1. COM

  2. LAN 1 & LAN

  3. USB 2.0

  4. HDMI

  5. COM (RS485)

  6. Reset Button

  7. Status LED

  8. A terminal block:
    RS422 (4-pin)
    Digital IO (4-pin)
    Power (1-pin)
    Ground (1-pin)

  9. DC IN

Rear View

DFI EC900-8MM-Industrial-Computers-08

DIN-rail Mount

Right View

DFI EC900-8MM-Industrial-Computers-09 Antenna Hole

Removing the Chassis Cover
Please observe the following guidelines and follow the instructions to open the system.

  1. Make sure the system and all other peripheral devices connected to it have been powered off.
  2. Disconnect all power cords and cables.

Step 1:
The 2 screws on the both sides of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use.

DFI EC900-8MM-Industrial-Computers-10 Step 2:
Slide the cover to open the system. DFI EC900-8MM-Industrial-
Computers-11

Installing an M.2 Card
Please follow the steps below to install the card into the socket. DFI EC900
-8MM-Industrial-Computers-12

Step 1:
Insert the card into the socket at an angle while making sure the notch and key are perfectly aligned.

DFI EC900-8MM-Industrial-Computers-13

Step 2:
Press the end of the card far from the socket down until against the stand- off.

Step 3:
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted DFI EC900
-8MM-Industrial-Computers-15

Installing an Antenna
Before installing the antenna, please make sure that the following safety cautions are well attended.

  1. Make sure the PC and all other peripheral devices connected to it has been powered down.
  2. Disconnect all power cords and cables.

Step 1:
There are antenna holes reserved on the right side of the system and by default
covered by rubber plugs. Please remove the plug prior to installing an antenna.

Step 2:
Connect the internal cable to the board’s antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below.

DFI EC900-8MM-Industrial-Computers-17

Mounting Options
The system features DIN-rail mount chassis that facilitates fast installation of the EC900- 8MM/EC910-8MM to a DIN rail.+

The DIN Rail mount kit includes the following:

  • Din-rail mount bracket
  • 2 screws

Step 1:
Use the provided mounting screws to attach the din-rail mount bracket to the top side of the system.

DFI EC900-8MM-Industrial-Computers-18

Step 2:
Install the sytem onto the rail. DFI EC900-8MM-Industrial-
Computers-19

Jumper Settings

IOJP1

DFI EC900-8MM-Industrial-Computers-20

  • 2-4 On: VCCP 5V (Default)

  • 3-5 On: DIO 5V (Default)

  • 1-3 On: DIO 3V3 (Default)

  • 2-4 On: VCCP 3V3 (Default)

PIN Assignment

RS485

DFI EC900-8MM-Industrial-Computers-23

Digital I/O Connector DFI EC900-8MM-Industrial-
Computers-24

DCN1/DC Jack DFI EC900-8MM-Industrial-Computers-25

COM ( For EC910-8MM) DFI EC900-8MM-Industrial-
Computers-26

FPJP1 DFI EC900-8MM-Industrial-Computers-27

TSJ1/DIO DFI EC900-8MM-Industrial-Computers-28

TSJ2 & TSJ3 -RS232 DFI EC900-8MM-Industrial-
Computers-29

CBCN1/CAN DFI EC900-8MM-Industrial-Computers-30

TSJ4 Debug DFI EC900-8MM-Industrial-Computers-31

AUJP1 DFI EC900-8MM-Industrial-Computers-32

DFI reserves the right to change the specifications at any time prior to the product’s release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/downloadcenter, or via the QR codes to the right DFI EC900-8MM-Industrial-
Computers-33

Quick Reference | EC900-8MM / EC910-8MM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals