ST UBLI PV-AZM-156 Stripping Pliers Instruction Manual
- May 15, 2024
- ST UBLI
Table of Contents
ST UBLI PV-AZM-156 Stripping Pliers Instruction Manual
Safety instructions
Importance of the instruction manual
NOT following the instruction manual and safety instructions
could result in life-threatening injuries due to electric shock, electric
arcs, fi re, or failure of the system.
- Follow the entire instruction manual.
Use the product only according to this instruction manual and the technical data.
The digital instruction manual and the technical data are available at: www.staubli.com/re-downloads.html
Intended use
The present hand tools are in place to deliver crimp excellence for Stäubli PV connectors with cables. Crimpings shall be carried out only in de-energized state of the cables.
The hand tool is NOT suitable for Live working (IEC 60900).
Stripping pliers PV-AZM-.
(ill. 1)
Stripping pliers PV-AZM-… incl. built-in stripping blades and Allen key
2.5 mm.
| Cable cross section mm² | AWG | Type | Order No. |
|---|---|---|---|
| 1.5; 2.5; 4; 6 | PV-AZM-156 | 32.6027-156 | |
| 4; 6; 10 | PV-AZM-410 | 32.6027-410 | |
| 12; 10; 8 | PV-AZM-128 | 32.6027-128 | |
| 10; 8; 6 | PV-AZM-106 | 32.6027-106 |
Individual components
-
PV-M-AZM-156
-
PV-M-AZM-410
-
PV-M-AZM-128
-
PV-M-AZM-106
| Cable cross section mm² | AWG | Type | Order No. |
|---|---|---|---|
| 1.5; 2.5; 4; 6 | PV-M-AZM-156 | 32.6057-156 | |
| 4; 6; 10 | PV-M-AZM-410 | 32.6057-410 | |
| 12; 10; 8 | PV-M-AZM-128 | 32.6057-128 | |
| 10; 8; 6 | PV-M-AZM-106 | 32.6057-106 |
Replacing the blades
(ill. 3)
Unscrew the three hexagonal socket screws A with the Allen key.
Loosen the length gauge stop B with a size 3 screwdriver.
(ill. 4)
Press the handles of the pliers fully together. This opens the blade holder C
so that the blades can be removed. Always replace the complete blade set (all
four blades).
(ill. 5)
Fit the new blades on the locating pins D of the blade holder C. The ground
side of the blade must face towards the blade holder C. Then return the
stripping pliers to their original position and tighten the hexagonal socket
screws and the length gauge stop.
Stripping
(ill. 6)
Set the length gauge to the desired stripping length.
(ill. 7)
Insert the cable in the appropriate cross-section range.
Push the cable against the length gauge stop.
(ill. 8)
Press the handles of the pliers fully together.
(ill. 9)
Open the PV-AZM-… and remove the stripped cable.
Manufacturer: Electrical Connectors AG Stockbrunnenrain 8 4123
Allschwil/Switzerland
Tel. +41 61 306 55 55
Fax +41 61 306 55 56
mail ec.ch@staubli.com
www.staubli.com/electrical
© by Stäubli Electrical Connectors AG, Switzerland – MA267 – 09.2023, Index e, Marketing Communications Subject to alterations
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>