EUERTE S08T Smart Door Knob User Manual

EUERTE S08T Smart Door Knob

IMPORTANT: Reod the instructions corefully before operating the appliance and keep them for future reference. Safety, Intelligence, All in Our Locks.
support@euerte.com
www.euerte.com

Congratulations

EUERTE SMART
Dedicated to providing market consumers with smart home devices, smart locks.

Hold on 3 “W”
We use cutting-edge technology to develop our products. We focus on human- computer interaction system. We focus on customer experience. Please visit our website www.euerte.com. Before installing, please scan the QR codes to watch our easy step-by- step installation video. If you have questions regarding the installation process, please contact us by mail support@euerte.com

Scan the QR code for prompt post-sales support and seamless communication. EUERTE PRODUCT

PRODUCT DIMENSIONS

PRODUCT DESCRIPTION

Indicator Light

1. Add fingerprint
   Blue light: The fingerprint light turns to blue as to indicate the lock is ready to add fingerprint.

2. Fingerprint, mobile phone APP unlock
   Green light: Success (the buzzer beeps once, and the fingerprint light flashes green to indicate prompt). Red light: Failed (the buzzer beeps twice, the fingerprint light flashes red to indicate prompt).

3. Low power
   Green +red light: When the lock is unlocked with fingerprint or mobile APP the buzzer beeps once and fingerprint light flash green and red.

INCLUDED IN THE BOX

ASSEMBLY DIAGRAM

CHECK THE DOOR’S DIMENSIONS

• Step 1 : Measure to confirm that the door is between 1⅞8″-2’*(35-54mm) thick.
• Step 2 : Measure to confirm that the hole in the door is 2⅛* (54mm).
• Step 3 : Measure to confirm that the backset is either 2⅜- 234 (60-70mm).
• Step 4 : Measure to confirm that the hole in the door edge is 1″(25 mm).

Note: If you have a new door, please drill the holes according to Drill Template.

INSTALLING LATCH AND STRIKE PLATE

1. Install latch into the door, make sure latch fits inside the door opening.
2. Install the strike into the door frame, make sure the latch can go into the strike smoothly.

INSTALLING EXTERIOR KNOB

Install the spindle Exterior Knob,Inser the spindle and the standoffs into the corresponding holes of the single latch.

Note: DO NOT CLOSE THE DOOR until-the door lock is fully installed and the batteries are installed.
Note: Make sure the knob is installed correctly with up † sign postioned on the top of the knob.

INSTALLING INTERIOR KNOB
Install the Interior Knob. Use a screwdriver to unscrew the battery cover screw. Connect the exterior knob and Interior knob wirings, Install the Interior Knob.

Note: The UP 1 faces upwards. After adjusting the Interior Knob, tighten theScrews B.

INSTALLING BATTERIES

Note:  Pay attention to the direction of the postive and negative electrodes when installing the battery.

DO NOT USE RECHARGEABLE BATTERIES.

DOWNLOAD THE TT LOCK APP

1. App Download Instructions
   • Scan the QR code on the right you can use Android and iOS to download the APP.
   • Android version software can be downloaded in the Google Play store. Search “TT LOCK”.
   • iOS version of the software can be downloaded in the iPhone App Store. Search “TT LOCK”.
2. Register and log in with your E-mail address.

ADDING DEVICE

1. Tap add device button.
2. Select the ALL Locks.
3. Continue to follow the instruction on the App interface.
4. Note : * Use the pin to enter pairing mode
5. Select your lock.
6. Add and dick S08T.

HOW TO ADD FINGERPRINT BY TT LOCK APP

1. Click member mangement.
2. Click Add Fingerprint.
3. Continue to follow the instruction on the App interfoce.

HOW TO DELETE FINGERPRINT BY TT LOCK APP

1. Top the fingerprint you want to delete.
2. Tap delete.

TROUBLESHOOTING

• Q: How to reset the S08T?
  A: Long press the set button on the Interior Knob until you hear the buzzer.
  A: Please select “restore factory setting” or ‘Delete device” by TT LOCK APP.

• Q: Dose S08T work with third-party accessories such as single latch?
  A: It is recommended to use the original accessories for best performance. and stability.

• Q: What notification will I receive when the battery is low?
  A: After the fingerprint and mobile APP are successfully unlocked (the buzzer beeps once, the fingerprint reader flashes green and then flashes red). When you unlock the device through the mobile App, you will recive a push notification message with low battery warning.

• Q: How con I unlock S08T if battery runs out?
  A: Connect a power bank to the knob with type-C cable as to activate for emergency access.
  A: Use the mechanical key and turn the key 90° to unlock, then turn the exterior knob to unlock the door.

Important Note: Please keep at least one key in secure location elsewhere as an extra precaution.

• Q: If I order 3 locks will anyone else have the some keys?
  A: Each set of locks is keyed differently.

• Q: Accidentally deleted the lock from the app, what should I do?
  A:

1. You delete the lock in the app, but the lock is not emptied. Please RESET the lock.
2. Add again on the TT LOCK APP.

• Q: My bluetooth won’t connect, what should I do?
  A:

1. Upgrade to the latest version of the firmware, authorize Bluetooth in the phone settings to allow access to the TT LOCK App.
2. Try to connect again.
3. If the connection is still not smooth, please contact our after-sale service.

• Q: How to enable passage mode?
  A:

1. Press set button on Interior Knob, then unlock the knob by fingerprint, after buzzer beeps, passage mode enabled.
2. Or you can enter “Setting” page in the APP, enable the passage mode.

• Q: How to disable passage mode?
  A:

1. Press set button on Interior knob, the passage mode will be disabled.
2. Or you can enter “Setting” page in the APP, disable the passage mode.

• Q: Why can’t unlock even though I’ve already entered my fingerprint?
  A:

1. Please make sure the fingerprints under dry conditions when enter into the APP.
2. Please delete the previous fingerprints and enter the new fingerprints (make sure that each side of the fingerprints are entered).

SPECIFICATIONS

FCC WARNING
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>