Mesqool CR01001eM Extra Loud Dual Alarm Clock with Vibration User Manual

: May 15, 2024
: Mesqool

Table of Contents

LOCATION OF CONTROLS
POWER RESOURCES
TIME SETTING
ALARM SETTING
DIMMER
DST
USB CHARGING
Vibrator
Contact our expert
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Mesqool CR01001eM Extra Loud Dual Alarm Clock with Vibration User Manual

LOCATION OF CONTROLS

Product Overview

Set Time & 12/24H ButtonHour Button
Minute Button
Dimmer & DST Button
OK & SNOOZE Button
Alarm Pause Button
Alarm OFF Button
Alarm 1 Button
Alarm 2 Button
PM Indicator
Alarm 1 Indicator
Alarm 2 Indicator
DST Indicator
Note: Batteries are notincluded
Bell Indicator
Vibrator Indicator
Bell & Vibrator Toggle Button
Volume + Button
Volume – Button
Battery Compartment
USB Port
DC Jack
Vibrator Insert Port
Holder (x 2pcs)
Speaker
Vibrator

POWER RESOURCES

Insert the two included holders into the back of the clock to avoid it being knocked over.

Install 2pcs 1.5V “AAA” size batteries to the proper terminals in the battery compartment to memorize the time setting in case of power outage.
NOTE: Batteries(not included) don’t support time display but can memorize time & alarm setting and trigger an alarm in case of AC power failure.
Connect the adapter line to DC jack, then plug into a 100~240V ACwall power outlet.

TIME SETTING

Press button once, display starts flashing.
Press button to set the hour press button to set the minute.
Press button or button to save time or wait for 5 seconds to confirm automatically.
To change 12H/24H time format Hold press button to switch 24H time format. Hold press button again to switch 12H time format.

ALARM SETTING

Set the Alarm

Press button, the alarm indicator will light up, the display – starts flickering.
Press button to set the hour, press button to set the minute.
Press button or button to save alarm time or just wait for another 5 seconds to confirm automatically or.
Push or button to adjust alarm volume.

Setting ALARM 2 is the same as ALARM 1.

Turn off Alarm

When alarm goes off:

Press button to temporarily turn off alarm for 9 minutes. Alarm will ring every next 9 minutes.
Press button to turn off today’s alarm.
The alarm indicator or is still on, which means alarmis still activated and will ring after 24 hours
Cancel Alarm
- Press button to turn off alarm 2 permanently, corresponding indicator turn off. Press button again to turn off alarm 1 permanently, corresponding indicator G} will turn off.
- If alarm 1 goes off, then press button, just turn off alarm1 permanently. indicator will turn off.
- If alarm 2 goes off, then press button, just turn off alarm 2 permanently. indicator will turn off.

DIMMER

Repeatedly press button to adjust the brightness of display for your preference.

There are 5 levels, The sequence is as follows:
3-4-5-4-3-2-1-2-3……..

DST

Hold press button to switch to DST function.
DST indicator will turn on.
Hold press button again to turn off DST function.
DST indicator will turn off.

USB CHARGING

Plug charging cable into device such as phone or tablet.
Device can charge your phone or tablet at the same time.

The maximum charge currents 1 Ampere.
USB Charging

Vibrator

Insert the vibrator plug into the vibrator jack of the machine, the bell indicator and the vibrator indicator will light up, indicating that the bell and the vibrator will be effective at the same time.
Press button, the ring indicator goes off, and the vibrator indicator stays on, which means that when the alarm goes off, the vibrator will take effect, but the bell will not sound.
Press button again, the ring indicator goes on, and the vibrator indicator goes off, which means that when the alarm goes off, the bell will sound, but the vibrator will not shake.
Press button again, the ring indicator and the vibrator indicator goes on, which means that when the alam goes off, the bell and the vibrator will be effective at the same time.