Mesqool CR01019 Stylish Calendar Clock with Thermometer User Manual

: June 16, 2024
: Mesqool

Table of Contents

Chapter 1 LOCATION OF CONTROLS
Chapter 2 POWER SOURCES
Chapter 3 TIME SETTING
Chapter 4 ALARM SETTING
Chapter 5 DIMMER
Chapter 6 USB & TYPE-C CHARGING
Chapter 7 DST
Chapter 8 RED INDICATOR LIGHT
Chapter 9 TEMPERATURE
Chapter 10 HUMIDITY
Chapter 11 ATTENTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Stylish Calendar Clock with Thermometer
THE BEST CHOICE FOR YOUR HOME

CR01019

Chapter 1 LOCATION OF CONTROLS

℉/℃
DATE
TIME & 12/24H
HOUR & Up
MINUTE & Down
SNOOZE & OK
VOL & DST
DIMMER
ALARM 1
ALARM 2
ALARM OFF
ALARM INDICATOR LIGHT
AM INDICATOR
PM INDICATOR
ALARM 1 INDICATOR
ALARM 2 INDICATOR
DST
MONTH DISPLAY
DATE DISPLAY
YEAR DISPLAY
WEEK DISPLAY
TEMPERATURE DISPLAY
HUMIDITY DISPLAY
BACKUP BATTERY COMPARTMENT
Type-C CHARGING PORT
USB CHARGING PORT
TEMPERATURE/HUMIDITY INDUCTOR
DC IN Jack
BRACKET
SPEAKER

Chapter 2 POWER SOURCES

Install 2pcs 1.5V “AAA” size batteries to the proper terminals in the battery compartment to memorize the time setting and the alarm will ring in case of power outage.
NOTE: Batteries are not included and don’t support time display or any other functions
Connect the adapter line to DC jack , then plug into a 100~240V AC wall power outlet.

Chapter 3 TIME SETTING

Press button once, display starts flashing.
Press button to set the hour.
press button to set the minute. Hold press or to quickly set the hour or minute.
Press button or button to save time or wait for another 10 seconds to confirm automatically.

To change 12H/24H time format
Hold press button to change 12H/24H time format.

YEAR/MONTH/DAY SETTING

Press once to maintain year flashing.
Press to increase year. Press to reduce year.
Hold press or to quickly increase or reduce.
When you finish the year adjustment. Press to save the setting.
When month flashing, repeat Step-2 and Step-3 to set and save the month.
When day flashing, repeat Step-2 and Step-3 to set and save the day.

Chapter 4 ALARM SETTING

Press button, the alarm indicator will light up, the display starts flickering.
Press button to set the hour, press button to set the minute. Hold press or to quickly set the hour or minute.
Press button or button to save alarm time or just wait for another 10 seconds to confirm automatically.
When the display “Mon-Sun” flashes.Press or to adjust alarm period range. Mon-Sun / Mon-Fri / Sat-Sun/OneTime. Press button or button again to save setting.

Setting ALARM 2 is the same as ALARM 1.
Set Alarm Ring Volume
Repeat button to adjust the alarm ring volume for your preference.
There is 5 levels, The sequence is as follows:
03(default)-04-05-04-03-02-01-02……..

Turn off Alarm
When alarm goes off:

Press button to temporarily turn off alarm for 9 minutes. Alarm will ring every next 9 minutes.
Press button to turn off alarm for 24 hours. The alarm indicator or is still on, which means alarm is still activated and will ring after 24 hours.

Cancel Alarm

Hold press button to turn off alarm1 and alarm 2 permanently. And corresponding indicator and will turn off.
Hold press button, just turn off alarm 1 permanently. indicator will turn off.
Hold press button, just turn off alarm 2 permanently. indicator will turn off.
If alarm 1 goes off, then hold press or , just turn off alarm1 permanently. indicator will turn off .
If alarm 2 goes off, then hold press or , just turn off alarm 2 permanently. indicator will turn off.

Chapter 5 DIMMER

Repeat button to adjust the brightness of display for your preference.
There is 5 levels, The sequence is as follows:
05(default)-04-03-02-01-02……..

Chapter 6 USB & TYPE-C CHARGING

Plug charging cable into device such as phone or tablet.
Device can charge both your phone or tablet at the same time.
The maximum charge current is 1 Ampere.

Chapter 7 DST

Hold press button to switch DST function. DST indicator will turn on.
Hold press button again to turn off DST function. DST indicator will turn off.

Chapter 8 RED INDICATOR LIGHT

When the alarm goes off，the Red Indicator Light will flash.

Chapter 9 TEMPERATURE

TEMPERATURE FORMAT SWITCH
Displays in Fahrenheit by default. If you want to switch Fahrenheit / Celsius. Just press button.

IMPORTANT REMINDER

It may take 1 minute for the temperature sensor to complete the initialization.
Accuracy of thermometer is 1 degree Celsius.
There might be 1-3 degrees Celsius deviation within normal limits due to unstable air flow and room heating.