TAC 3S-19C110TN 3 Inch Sidebars Installation Guide

: June 28, 2024
: TAC

Table of Contents

TAC 3S-19C110TN 3 Inch Sidebars
Product Usage Instructions
Passenger/Right side Installation Pictured
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAC 3S-19C110TN 3 Inch Sidebars

Specifications

Product Name: 3-Inch Sidebars
Compatible Vehicles: 2019-2024 Chevy Silverado/GMC Sierra 1500 Double Cab, 2020-2024 Chevy Silverado/GMC Sierra 2500-3500 Double Cab
Part Number: 3S-19C110TN
Website: www.tacautoparts.com

Product Usage Instructions

Parts List

1 Driver/Left Sidebar
1 Passenger/Right Sidebar
6 Mounting Brackets
12 8-1.25mm x 30mm Hex Bolts
12 8-1.25mm x 25mm Combo Bolts
12 8mm Lock Washers
12 8mm x 24mm x 2mm Flat Washers

Installation Procedure

Remove contents from the box and verify all parts are present.
Select a mounting bracket and attach it to the factory threaded holes using provided hardware, but do not tighten.
Move along the body to the next mounting location and repeat step 2 for the remaining brackets.
Attach the Passenger/Right Sidebar to the brackets using the provided combo bolts. Avoid sliding or rotating the Sidebar to prevent damage.
Level and adjust the Sidebar, then tighten all hardware.
Repeat steps 2-5 for the Driver/Left Sidebar.
Periodically inspect the installation to ensure all hardware is secure and tight.

Cleaning Instructions
To protect your investment, avoid using polish or wax containing abrasives that could damage the finish. Mild soap can be used to clean the Sidebars.

FAQ

Q: Can these sidebars be installed on vehicles other than those specified?
A: No, these sidebars are specifically designed for 2019-2024 Chevy Silverado/GMC Sierra 1500 Double Cab and 2020-2024 Chevy Silverado/GMC Sierra 2500-3500 Double Cab models. Installing them on other vehicles may not be compatible or recommended.
Q: How often should I inspect the installation?
A: It is recommended to do periodic inspections to ensure that all hardware is secure and tight. Check the installation every few weeks initially, and then at least once a month thereafter.

INSTALLATION INSTRUCTIONS
3INCH SIDBARS
2019-2024 CHEVY SILVERADO/GMC SIERRA 1500 DOUBLE CAB 2020-2024 CHEVY SILVERADO/GMC SIERRA 2500-3500 DOUBLE CAB EXCLUDES SILVERADO “LD,” AND SIERRA “LIMITED”
PART# 3S-19C110TN

3INCH SIDBARS
2019-2024 CHEVY SILVERADO/GMC SIERRA 1500 DOUBLE CAB 2020-2024 CHEVY SILVERADO/GMC SIERRA 2500-3500 DOUBLE CAB EXCLUDES SILVERADO “LD,” AND SIERRA “LIMITED”

PARTS LIST:

TAC-3S-19C110TN-3-Inch-Sidebars-01 $TAC-3S- 19C110TN-3-Inch-Sidebars- $1$$

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

Start the installation under the Passenger/Right side of the vehicle. Locate the 4 plugs along the bottom edge of the body. Mounting Brackets will attach to the 1st, 2nd and 4th threaded mounting holes,
(Figures 1, 3 & 4). Remove the plastic plugs from each mounting location. Directly above each threaded hole is a top mounting location on the side of the body panel. Hold a Bracket up in place to help determine the mounting holes to use along the body. NOTE: Thread an 8mm Hex Bolt into the threaded holes to clear paint as required.
Select (1) Mounting Bracket. Attach the Mounting Bracket to the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 2). Do not tighten hardware.
Move along the body to the next mounting location. Repeat Steps 1 & 2 to attach a Mounting Bracket to the 2nd (center) mounting location. Repeat this Step to attach a Bracket to the last mounting location toward the back of the cab.
Select the Passenger/Right Sidebar. Use the illustration above to help determine the correct Sidebar. NOTE: The rear step pad is closer to the end of the Sidebar. Place the Sidebar on top of the Brackets. IMPORTANT : Do not slide, (front to back or rotate), the Sidebar on the Brackets or damage to the finish may result. Attach the Sidebar to the Brackets with (6) 8mm Combo Bolts, (Figure 5).
Level and adjust the Sidebar and fully tighten all hardware.
Repeat Steps 1—5 to attach the Driver/Left Sidebar.
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investmen t, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean Sidebars.