HAKINAKU PT07 Radon Detector for Home Smart WiFi Radon Tester User Manual

HAKINAKU PT07 Radon Detector for Home Smart WiFi Radon Tester

ATTENTION:
Please thoroughly read this user guide save the document for future reference and pass it on to any subsequent owner. Images in this user guide are representative only. Actual products may vary slightly.

This model requires a home Wi-Fi router and internet to connect to a mobile device. Requires 820.11b/g/n (2.4GHz) Wi-Fi. Please note this device will not work on 5GHz Wi-Fi.

Safety Instructions

We will not take responsibility for any loss or damage resulting from not following the instructions of this operating guide.

• The device must not be disassembled or remodeled, and never be subjected to shocks or impacts.
• Do not leave the device outdoors where the temperature is below/above the operating range.
• Do not place the device close to objects with flames, heat sources (oven or sunlight), cold sources, liquid, or extreme temperature changes.
• Do not touch any part of the product with wet hands.
• Do not allow metal objects (like pins, and keys) to contact terminals or plugs.
• Do not cut, damage, or modify the power cord.
• The device is not intended to be used as a reference sensor, and we will not bear responsibility for any damage that may result from inaccurate readings.
• Never use detergents or solvents to clean the device.
• Avoid spraying air freshener, hair spray, or other aerosols near the sensor.

Declaration of Conformity
PT04 series conforms with the essential requirements and other relevant provisions of the CE, FCC, and Ro HS.

Product Overview

This smart radon gas detector is the new innovative fastest radon sensor, which has the highest sensitivity, 30cph/pCi/ I on the market today. This detector uses a pulsed ionization chamber and a special high-impedance differential amplifier circuit to offer the highest signal-to-noise ratio. It effectively detects the secondary charges that were generated from collisions with air and a particle caused by Radon or Radon’s progeny. The accuracy and precision are ±10% at 10pCi/I Each sensor has been individually calibrated by equipment which is already calibrated to traceable international standards.

1. 1. Wi-Fi icon
2. Memory card icon
3. Alarm icon
4. Real-lime reading
5. 1-day average value
6. Radon level light strip indicator
7. Radon Volume
8. 7 days average value
9. Continuous monitoring lime
10. Power Port
11. Memory Card Port
12. Control Panel

Technical Specifications

• Sensor Type: Pulsed ion chamber
• First Sampling Data: 10 min
• First Accurate Result: 1 hr
• Data Update Interval: 10 min
• Sensitivity: 30cph/pCi/L, 0.Scpm/pCi/L
• Range: o.10~99_9pCi/L
• Precision: < 10% at 10pCi/L(370Bq/m3}
• Accuracy: < ±10% at lOpCi/L
• Connectivity: 2.4GHz Wi-Fi
• Alarm: Audible alert & Visual indicator
• Radon Level Indicator: Green, Orange, Red LEDs
• Power: DC 12V/2A (12V DC Adaptor)
• Operating Range: 1~so°C, RH 80%

Radon Level Chart

1 pCi/L=37 Bq/m3, Pico Curie Per Liter (pCi/L}, Becquerel Per Cubic Meter (Bq/m3)

Radon and Health
Radon is a naturally occurring radioactive gas released in rock, soil, and water that can build up to dangerous levels inside any home; this means new and old homes, as well as sealed and drafty homes, and homes with or without a basement. Radon gas is odorless and invisible and the only way to know if your home has a radon problem is to detect it. Breathing radon can increase your risk of lung cancer. Radon is the main cause of lung cancer among people who do not smoke. It is the second leading cause of lung cancer for people who do.

Device Operation Guide

The device draws power from an external power source of DC 12V/2A. To connect to an outside power source use the DC 12V adaptor that comes with the device.

Turn ON/OFF:
Press and hold the power button to activate/ deactivate the device.

Measuring Mode:

• The measurements start autonomously after connecting the power supply. The first measurement result will be available as soon as the first sampling interval is accomplished within 10 minutes. The first accurate result is available after 1 hour of continuous monitoring.
• If the measured value is equal to or greater than 99.99pCi/L (3700Bq/m3), The reading will display OVER.

Backlit Display:

• Quick press the button 2 times to turn off the backlight, and press the button to turn on the backlight.
• OR control the backlight with the Tuya App.

Alarm Threshold Reset:
Press and hold both and buttons to enter resetting mode, see the below figure.

• Reset the alarm threshold value by alarm threshold indicator.
• Reset the alarm shutdown threshold value by the alarm shutdown threshold indicator.
• Press the button to increase the threshold value, and press the button to decrease the threshold value.
• Press the POWER button to save the changes and move to the next setting.
• Press the POWER button again to go back to the detection mode.

Default Alarm Threshold Value:
bad level is 2.7-4.0 pCi/L, and severe level above 4.0 pCi/L.

Alarm Length:

• When the radon level is detected above the fair level, the alarm will chirp for 20 seconds.
• When the radon level is detected greater than the poor level, the alarm will chirp for 60 seconds.

Wi-Fi Setting:
Quick press the POWER button 3 times to activate/ deactivate Wi-Fi. Quick press the POWER button 5 times to reset Wi-Fi to the default factory setting.

Data Storage Capacity:
This device comes with a 128MB memory card, which can continuously store radon data for 12 months and transfer the stored data to a PC.

Recommended Placement

• The proper placement of the radon gas detector should be roughly at the same height as a person’s head (breathing), ie – on the floor of a game room; on a table at an office; or a nightstand in a bedroom.
• Radon detector uses highly delicate sensors. It is strongly recommended to avoid exposing ventilation holes on the device to direct sunlight, as well as keep the device away from sources of strong electromagnetic radiation such as cell phones, computers, radios, and high-power electronic devices.
• In the case of dangerously high radon levels, it is necessary to fully and properly ventilate the venue and preferably locate the source of the gas leak and remove it if possible. Another option is to seal off the leak.

Measurement Instructions

• The device should be placed at a location that is representative of the indoor air quality of a room.
• Make sure the device is at least 59 inches/50cm from the floor and 15 cm from the wall because the wall itself could be the origin of the radon inside a room.
• Do not move the device during use. Vibration can cause the device to pause the measurement.
• Please place the device at a location with a good Wi-Fi connection so this device will send notifications to the App.

Radon Gas and Health

Radon is a naturally occurring radioactive gas released in rock, soil, and water that can build up to dangerous levels inside any home; this means new and old homes, as well as sealed and drafty homes, and homes with or without a basement. Radon gas is odorless and invisible and the only way to know if your home has a radon problem is to detect it.

Breathing radon can increase your risk of lung cancer. Radon is the main cause of lung cancer among people who do not smoke. It is the second leading cause of lung cancer for people who do. EPA estimates that radon causes more than 20,000 deaths from lung cancer each year in the U.S. If you smoke and your home has a high radon level, your risk of lung cancer can increase even more.

Tuya App Guide

• Download the “Tuya” App on the Google Play Store or Apple App Store, or scan the QR code on the next page and create an account with the phone number or email ID.

• Make sure Bluetooth is enabled on your smartphone and Wi-Fi is working on 2.4GHz, which will not work on 5GHz.

• If the Wi-Fi icon is not on the display, quickly press POWER 3 times to enable Wi-Fi on the device.

• When you connect this device to another smartphone or reset the App connection, quickly press the POWER button 5 times to return to the factory setting within 5-10 seconds.

• Step 01
  Tap Add Device or”+”.

• Step 02
  Tap Add. The app automatically finds devices for connecting.

• Step 03
  Input your Wi-Fi ID and password, and then tap Next.

• Step 04
  After the device is ready on the App, Tap Done.

• Step 05
  Select real-time and Device alarms to check alarm notifications sent to your smartphone App.

• Step 06
  Find the real-time alarm notifications sent to you by time order

• Step 07
  Find the real-time historical records as the above figure.

• Step 08
  Find the real-time historical records in time order, which is stored on a memory card for download to a PC.

• Step 09
  Tap Alarm lifted value and input values by “-“or”+”.

• Step 10
  Tap the Alarm threshold value and input values by “-“or”+”.

• Step 11
  Tap the EDIT icon on the device information page.

• Step 12
  Tap Remove Device and remove this device from the App.

• Step 13
  Tap the EDIT icon above to revise the name of the device

• Step 14
  Input a name so that you can remember the location when you have several devices in your house.

• Step 15
  Return to the Home Page and tap on “+” at the upper right corner to add a second device to the same App.

• Step 16
  Tap Add and follow the in-app steps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>