IKEA RÅKALL Fridge Freezer Integrated Instruction Manual

June 1, 2024
Ikea

RÅKALL

Fridge Freezer Integrated

IKEA RÅKALL Fridge Freezer IntegratedIKEA
RÅKALL Fridge Freezer Integrated - Figurewww.ikea.com

Product description

Carefully read the user handbook before using the appliance.

IKEA RÅKALL Fridge Freezer Integrated - Product

Accessories

Refrigerator compartment

  1. Fan
  2. Glass shelves
  3. Crisper drawer lid
  4. Crisper
  5. Crisper divider
  6. Rating plate (at the side of crisper drawer)
  7. Control panel with LED light
  8. Dairy balcony
  9. Door balcony
  10. Bottle holder
  11. Bottle balcony

Least cold zone
Intermediate temperature zone
Coldest zone
Least cold zone
Intermediate temperature zone
Coldest zone
Freezer Compartment
7 Top drawer (storage area for frozen and deep frozen food)
8 Middle drawer (storage area for frozen and deep frozen food)
9 Bottom drawer (for freezing fresh foods)

Characteristics, technical data and images may vary according to the model.

First time use

Connect the appliance to the power supply. The ideal food storage temperatures are already factory-set (intermediate).
Note: after being switched on, the appliance needs 4-5 hours in order to reach the correct temperature to store a typical volume of food.

Important!

This appliance is sold in France. In accordance with regulations valid in this country it must be provided with a special device (see figure) placed in the lower compartment of the fridge to indicate the coldest zone of it.

Control panel

A Led light
B Refrigerator compartment temperature
C Button for temperature regulation and Stand-by function
Refrigerator and freezer operation
The appliance’s refrigerator compartment features a control panel with LED lights. A different temperature can be set using the C button as shown in the figure. The three green LED indicators indicate the refrigerator compartment set temperature. The following adjustments are possible:

Leds on

Set temperature
High (least cold)
Medium-high
Intermediate
Medium-low
Low (coldest)
To avoid food waste, please refer to the recommended setting (Intermediate), and storage times found in the user manual.
To download the full version visitwww.ikea.com

Functions

Fan
The fan is pre-set to ON. You can turn the fan on/off by pressing the light button (as shown in figure below at step 2) and at the same time the button C as shown in figure 3.
The light will flash just once if the fan is OFF, or it will flash below at step 3 times if the fan in ON. If the ambient temperature exceeds 27°C, or if drops of water are present on the glass shelves, it is essential to have the fan on to ensure  the proper preservation of the food. Deactivation of the fan allows energy consumption to be optimised.

IKEA RÅKALL Fridge Freezer Integrated -Fan

Stand-by
Press the C button for 3 seconds to deactivate the appliance (the control panel and lights remain off). Press the button again briefly to reactivate the appliance.
Note: This operation does not disconnect the appliance from the power supply.
Note: the ambient temperature, frequency of door opening and position of the appliance can affect the temperature inside the two compartments.
These factors must be taken into account when setting the thermostat.

LED light
LEDs last longer than traditional light bulbs, improve internal visibility and are environmentally friendly.
Contact the Service Centre if replacement is necessary.

Refrigerator compartment
Defrosting of the refrigerator compartment is completely automatic.
The formation of water droplets on the rear internal wall of the refrigerator compartment indicates that the automatic defrosting is underway.
The defrost water automatically runs into a drain outlet and then into a container from where it evaporates.
Caution! The refrigerator accessories must not be placed in a dishwasher.
Freezer compartment
This appliance is a refrigerator with a star freezer compartment.
Packaged frozen food can be stored for the period of time indicated on the packaging. Once defrosted, food must be used within 24 hours.

Installation

The appliance must be handled and installed by two or more persons – risk of injury. Use protective gloves to unpack and install – risk of cuts.
Installation, including water supply (if any), electrical connections and repairs must be carried out by a qualified technician. Do not repair or replace any part of the appliance unless specifically stated in the user manual. Keep children away from the installation site. After unpacking the appliance, make sure that it has not been damaged during transport.
In the event of problems, contact the dealer or your nearest Aftersales Service. Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of reach of children – risk of suffocation. The appliance must be disconnected from the power supply before any installation operation – risk of electric shock. During installation, make sure the appliance does not damage the power cable – risk of fire or electric shock.
Only activate the appliance when the installation has been completed.
Be careful not to damage the floors (e.g. parquet) when moving the appliance. Install the appliance on a floor or support strong enough to take its weight and in a place suitable for its size and use. Make sure the appliance is not near a heat source and that the four feet are stable and resting on the floor, adjusting them as required, and check that the appliance is perfectly level using a spirit level. Wait at least two hours before switching the appliance on, to ensure that the refrigerant circuit is fully efficient.
WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING: To avoid a hazard due to instability, positioning or fixing of the appliance must be done in accordance with the manufacturer instructions. It’s forbidden to place the refrigerator in such way that the metal hose of gas stove, metal gas or water pipes, or electrical wires are in contact with the refrigerator back wall (condenser coil).
To guarantee adequate ventilation, leave a space on both sides and above the appliance. The distance between the rear of the appliance and the wall behind the appliance should be 50 mm, to avoid access to hot surfaces. A reduction of this space will increase the Energy consumption of product. Please remove the power cord from condenser hook during installation before connecting product to power supply.
When contacting our Service Provider, please state the codes provided on your product’s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model identifier that can be used to consult the https://eprel.ec.europa.eu database portal.

IKEA RÅKALL Fridge Freezer Integrated -LED light 1

Inspection check list
Please follow the inspection checklist before using your appliance.
If any answer is NOT please follow the relevant action.
Please remember to write down the product serial number and article number as required and attach your receipt to this page.

Product serial number (rating plate) *|
---|---
Product artical number (rating plate) **|
Purchasing date|

IKEA RÅKALL Fridge Freezer Integrated -LED light 2

General information

The drawers, baskets and shelves should be kept in their current position unless otherwise specified in this quick guide. The light system inside the refrigerator compartment uses LED lights, allowing for better lighting than with traditional light bulbs, as well as for very low energy consumption. Doors and lids of the refrigeration appliance should be removed before disposal in the landfill, to avoid children or animals getting trapped inside.
This product contains a light source of energy efficiency class G.

Technical data

IKEA RAKALL 4 219 35 E
Brand Model Freezing capacity (kg/24h) Energy consumption (kwh/year) Noise
level (dba) Energy class

© Inter IKEA Systems B.V. 2021

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Ikea User Manuals

Related Manuals