JALL K8 Wake Up Light Sunrise Alarm Clock User Manual

JALL K8 Wake Up Light Sunrise Alarm Clock

Product Information

• Specifications:
  • Alarm Clock Radio
  • Frequency Range: 76.0 MHz – 108.0 MHz
  • Snooze Function
  • Wire Antenna

Product Usage Instructions

• Stopping the Alarm:
  • There are two ways to stop the alarm:
  • When the alarm goes off, press and hold the snooze button.
  • If there is no operation within 20 minutes, the alarm will automatically turn off.
• Radio Performance:
  • To optimize radio performance:
  • Uncoil the wire antenna completely for better reception.
  • Adjust the antenna position while the radio is working to achieve the best reception effect.
• Scanning for Radio Stations:
  • To scan for available radio stations:
  • Press and hold the snooze button for 2 seconds.
  • The device will scan all available stations from 76.0 MHz to 108.0 MHz.
  • Once the scan is complete, the device will play the first available station.

FAQs

• Q: How do I set the alarm on the clock radio?
  • A: To set the alarm, refer to the user manual for detailed instructions on setting the alarm time and desired alarm sound.
• Q: Can I use batteries to power the clock radio?
  • A: Yes, you can typically use batteries as a backup power source in case of a power outage. Check the user manual for battery compatibility and installation instructions.

Product Introduction

1. Snooze, +/-(Clock Time&Volume, Alarm clock Time&Sound& Volume&Light Intensity Adjustment), FM Radio Manual Searching
2. Alarm 1 on/off button/Alarm 1 Setting
3. Alarm 1 on/off button/Alarm 2 Setting
4. Time Display Brightness/Time Setting
5. Radio on/off Button/FM Radio Automatic scanning
6. Relaxing Bedtime Sounds on/off/sound change Button
7. Radio Volume Increase/Manual Station Selection
8. Radio Volume Decrease/Manual Station Selection
9. Fall Asleep Function
10. Wake up light/Mood light on/off /colour change Button
11. RGB Mood Light on/off/color change Button
12. Increase Light Intensity
13. Reduce Light Intensity
14. Every Day/Weekday/Weekend Mode for Alarm1
15. Every Day/Weekday/Weekend Mode for Alarm2
16. Battery Compartment
17. USB Charging Port
18. DC Charging Port

Setting and Maintenance

• First use
  • Connect the AC adapter to the power jack of Wake-up Light and plug the AC adapter into a household socket with 100-240V.
  • Place the Wake-up Light 40-50cm from your head, for example on a bedside table.
• Install battery
  • The wake-up Light is pre-installed with a CR2032 battery, please remove the insulating sticker for normal use.
• Storage
  • Wake-up Light should be placed into the carton or stored at a cool and dry place.
• Cleaning
  • Wipe the dust off with a soft and damp cloth. Please do NOT use liquid or abrasive cleaners.

Time Display Setting

• The default clock time is AM-noon when you plug in the appliance for the first time.
• Notice: The following operation should be operated step by step.

1. Hour Time Setting
   • Press and hold the time set button for at least 25 to start the hour setting after the time display is on, the hour indicator in the display blink, then rotate the + and – on the SNOOZE button to change by one hour, press the to confirm and the minute time set button indicator in the display blink at the same time.
2. Minute Time Setting
   • Rotate the + and – on the snooze button to change by one minute after the minute indicator in the display blink, press the time set button to confirm and start to set 12-hour(AM/PM) or 24-hour clock mode at the same time.
3. Adjusting 12-hour(AM/PM) or 24-hour Clock Time
   • Rotate the + and – on the SNOOZE button to choose between a 12-hour(AM/PM) and a 24-hour clock, and press the time set button to confirm and start to set what day is today.
4. MON-SUN Setting
   • Rotate the + and- on the snooze button to choose what day is today after its icon in the display blink, then press the time set button to choose a day from MON to SUN and complete all the time settings.
   • Notice: The time of day will revert to AM midnight if the device is disconnected from the mains power supply with no backup batteries inserted if the backup batteries are too weak or if the insulating sticker has not been removed.

Alarm Setting – Switching the Alarm on/of

• Prerequisite: The time display is ON.
  • Press alarm 1 or alarm 2 if you want to switch the alarm on or off. The corresponding icon appears on the display when you switch on the alarm. It disappears when you switch off the alarm.
  • Notice: The operation modes of alarm 1 and alarm 2 are the same.

Alarm Setting – Alarm Day Setting

Prerequisite: The alarm1 icon or alarm2 icon appears on the display.

• Set, with the switch or switch, every day/weekday/weekend modes are available for alarm1 and alarm2, slide the switch to adjust the daily alarm as shown in the following picture:

Alarm Clock and Wake-up Light Setting

Notice: The following operation should be operated step by step.

1. Alarm Hour Time Setting
   • Press and hold the for at least 25 after the time display is on, the hour indicator in the display starts to flash, then rotate the + and – on snooze button to change by one hour, press the to confirm and the minute indicator in the display blink at the same time.
2. Alarm Minute Time Setting
   • Rotate the + and – on the snooze button to change by one minute after the minute indicator in the display starts to flash, press the to confirm and start to set the wake-up sound at the same time.
3. Wake-up Sound Setting
   • Rotate the + and – on the snooze button sound from 501 to 508 and OFF, press to choose a wake-up to confirm and start to set the alarm volume.
   • Notice: You can use wake-up sounds or the FM radio as a wake-up Sound. The Wake-up Light built-in 7 wake-up sounds (501 – S07), and 508 is FM radio. The corresponding icon appears on the display when you choose one.
4. Alarm Volume Setting
   • Rotate the + and – on the snooze button to adjust the volume from V01 to V16 (16 levels in total), then press the to confirm and start to set wake-up light intensity.
5. Wake-up Light Intensity Setting
   • Rotate the + and – on the snooze button to adjust the wake-up light intensity from L01 to L20, press the to confirm and start to set the dawn duration time of the wake-up light.
   • Notice: The screen displays show OFF, L01 – L20 in turn. You can choose OFF if you don’t need light, while L20 chosen means light intensity increases gradually from L01 to L20.
6. Dawn Duration Time of Wake-up Light
   • The dawn duration time is the time in which the light intensity of the lamp gradually increases to the set level before the alarm sound is played.
   • The range of dawn duration time of the wake-up light is 10-60MIN, the dawn duration time can be changed by 10 minutes to your preference by rotating the + or – on the snooze button , pressing the to confirm and complete all the alarm clocks and wake-up light profile setting.
   • Note: You can not select Wake-up Sound and Wake-up Light to be “OFF” at the same time.

Snooze Function

• The wake-up light turns on at the set time after alarm 1 or alarm 2 is activated, the light intensity increases to the set maximum light intensity before the alarm sound is played.
• The following operations are available when the alarm sound is played, you can operate them according to your requirements:

1. Snooze
   • You can press the button to snooze for a while. The wake-up light and the alarm sound stop. After 9 minutes, the lamp turns on and the alarm sound is automatically played again.
   • ( User Tip: The number of snoozes is unlimited.)
2. Manually stop the alarm
   • There are 2 ways to stop the alarm
   • Press alarm 1 or alarm 2 if you want to turn off the current wake-up light and alarm sound when the alarm sound is played or the alarm is snoozed.
   • When the alarm goes off, hold the snooze button for 3 seconds to turn off the alarm for the day.
3. Automatically stop the alarm
   • If there is no operation within 20 minutes, the alarm will automatically turn off.
   • Note:
   • The alarm 1 or alarm 2 icon flashes on the display when the alarm is snoozed.
   • The alarm 1 or alarm 2 icon stays bright on the display, which means alarm 1 or alarm 2 is activated.

FM Radio Operation

To get a great radio performance, we recommend making the wire antenna un- coiled completely. When the radio is working, please adjust the antenna position to get the best reception effect.

Notice: The following operations should be operated step by step.

1. Switching on/off the radio
   • Press the FM on/off button to switch on/off the FM radio after the time display is on.
2. FM automatic scanning
   • To scan radio frequencies automatically when the time display is on, press and hold the button for 2 seconds and the device will scan for all available stations from 76.0 MHz to 108.0 MHz. When the scan is complete, the device will play the first available station.
3. Manual station selection

   •   * After FM automatic scanning has been completed from 76MHz to 108.0MHz, then  button for 25 to adjust the last/next radio station.

4. Adjust the FM Radio Volume
   • Click the button to increase or decrease the radio volume after the radio display icon is on. station.
5. FM Radio Manual Searching
   • Rotate the + and – on SNOOZE button to manually adjust the FM frequency to change by 0.1MHZ after the radio display icon is on.

Relaxing Bedtime Sound Function

1. Switching on the relaxing bedtime sound function
   • Press the button to switch on the relaxing bedtime sound function after the time display is on and the relaxing bedtime sound icon appears on the display.
   • Then click the button to change sounds from 501 to 508, and click the to adjust the sound volume.
2. Two ways to switch off the relaxing bedtime sound function
3. The relaxing bedtime sound function has 8 sounds: S01-508, it will be turned off if you click button again when the 508 sound is set, and the relaxing bedtime sound icon disappears from the display.
4. To switch off the relaxing bedtime sound function, press and hold down the button for 2 seconds. The relaxing bedtime sound icon disappears from the display.

The appliance has 3 light modes: wake-up light, mood light and RGB mood light. Please make sure the device is connected to the mains power supply and the time display is on before you are ready to do the following operations:

Light – Wake-up Light Mode

1. Press the button to switch on the wake-up light and use it as a bedside light.
2. You can adjust the light intensity by pressing the + and – buttons 20 levels of brightness adjustable
3. To switch off the wake-up light, press the button again.

Light – Mood Light Mode

1. Press and hold the button for at least 25 on the device to switch on the mood lighting.
2. Click the button to change the colour of the mood lighting. The LEDs light up in the following sequence: red – orange → yellow – green → blue → indigo → purple → etc.
3. You can adjust the mood light intensity by pressing the + and – buttons 10 levels of brightness adjustable
4. To switch off the mood light, press and hold the button for at least 25 again.

Light – RGB Mood Light Mode

1. Press the button to switch on the RGB mood light and use it as a mood light too.
2. Click the button to change the colour of RGB mood lighting from CO1 to C07. There are 7 different RGB lighting colours in total.
3. You can adjust the RGB mood light intensity by pressing the + and-buttons • 10 levels of brightness adjustable
4. To switch off the RGB mood light, press and hold the button for at least 2S.

Fall Asleep Function

Notice: The following operation should be operated step by step.

1. Press the fall asleep button to switch on the fall asleep function after the time display is on.
2. The set fall asleep time appears on the display and flash for 5 seconds.
3. Rotate the + or — on the Snooze button to adjust the time (10 to 120, 180 or 240 minutes).
4. You can set the desired light (3 light modes are available) and/or FM radio, or light (3 light modes are available) and/or the relaxing bedtime sounds when you want the light and/or FM radio, or the light and/or the sound of the Wake-up Light to stay on during a set time (10 to 120, 180 or 240 minutes) before you go to sleep. The FM radio, lamp and/or sound switch off automatically after the set time.
5. You can track your remaining bedtime by clicking the button after the fall asleep function is activated.
6. To switch off the fall asleep function, press and hold the fall asleep button for at least 2 seconds. The fall asleep icon disappears from the display.

Time Display Brightness

• You can control the brightness of the clock’s display manually according to your preferences. For example, you can change the brightness of the display so that intense light won’t wake you in the morning. There are 3 brightness levels, click the button to adjust it after the time display is on. The time display turns off if you click the button once more when the time display brightness is at the maximum brightness.

Change Battery

Remove the screw from the battery case with a screwdriver, insert the battery into the battery case, while the positive-electrode is upward; insert the cover of the battery case into the slot of the battery case at the left side; tighten the battery case.

Contact us

If you have any using problems with the product, please don’t be hesitant to contact us, we will be happy to help you solve various product problems so that you can get a better experience with the products. Ecobre@outlook.com

For a lifetime-warranty, please contact Ecobre@outlook.com with your Amazon Order Number to register the product warranty.

CUSTOMER SUPPORT

• Ecobre@outlook.com.

Read and follow all instructions in this user manual before use.
Notice: The CR2032 batteries only save the time of day and the programmed wake time. All functions are only possible with mains power operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>