JALL CR2032 Wake Up Light User Manual

Wake-up Light User Manual

Read and follow all instructions in this user manual before use.
Notice:
The CR2032 batteries only save the time of day and the programmed wake time. Al functions are only possible with mains power operation

Product Introduction

1. Snooze, +/-(Clock Time&Volume, Alarm clock Time&Sound& Volume&Light Intensity Adjustment), FM Radio Manual Searching
2. Alarm 1 on/off button/Alarm 1 Setting
3. Alarm 1 on/off button/Alarm 2 Setting
4. Time Display Brightness/Time Setting
5. Radio on/off Button/FM Radio Automatic scanning
6. Relaxing Bedtime Sounds on/off/sound change Button
7. Radio Volume Increase/Manual Station Selection
8. Radio Volume Decrease/Manual Station Selection
9. Fall Asleep Function
10. Wake up light/Mood light on/off /color change Button
11. RGB Mood Light on/off/color change Button
12. Increase Light Intensity
13. Reduce Light Intensity
14. Every Day/Weekday/Weekend Mode for Alarm1
15. Every Day/Weekday/Weekend Mode for Alarm2
16. Battery Compartment
17. USB Charging Port
18. DC Charging Port

Setting and Maintenance

First use
Connect the AC adapter to the power jack of Wake-up Light and plug the AC adapter into a household socket with 100-240V. And place the Wake-up Light 40-50cm from your head, for example on a bedside table.
Install battery
Wake-up Light is pre-installed with a CR2032 battery, please remove the insulating sticker for normal use.
Storage
Wake-up Light should be placed into the carton or stored at a cool and dry place.
Cleaning
Wipe dust off with a soft and damp cloth. Please do NOT use liquid or abrasive cleaners.

Time Display Setting

The default clock time is AM 12:00 when you plug in the appliance for the first time.
Notice: The following operation should be operated step by step.

1. Hour Time Setting
   Press and hold the time set button for at least 2S to start hour setting after the time display is on, the hour indicator in the display blink, then rotate the + and – on SNOOZE button to changes by one hour, press the time set button to confirm and the minute  indicator in the display blink at the same time.

2. Minute Time Setting
   Rotate the + and – on snooze button to changes by one minute after the minute indicator in the display blink, press the time set button to confirm and start to set 12-hour(AM/PM) or 24-hour clock mode at the same time.

3. Adjusting 12-hour(AM/PM) or 24-hour Clock Time
   Rotate the + and – on SNOOZE button to choose between a 12-hour(AM/PM) and a 24-hour clock, press the time set button to confirm and start to set what day is today.

4. MON – SUN Setting
   Rotate the + and- on snooze button to choose what day is today after its icon in the display blink, then press the time set button to choose a day from MON to SUN and complete all the time setting.

Notice: The time of day will revert back to AM 12:00 dclock if the device is disconnected from the mains power supply with no back-up batteries inserted or if the back-up batteries are too weak o if insulating sticker do not be removed.

Alarm Setting – Switching the Alarm on/of

Prerequisite: The time display is ON.
Press alarm 1 or alarm 2 if you want to switch the alarm on or off. The corresponding icon appears on the display when you switch on the alarm. It disappears when you switch off the alarm.
Notice: The operation modes of alarm 1 and alarm 2 are exactly the same.

Alarm Setting – Alarm Day Setting

Prerequisite: The alarm1 icon o alarm2 icon appears on the display.
Set, with the 14 switch or 15 switch, every day/weekday/weekend modes are available for alarm1 and alarm2, slide the switch to adjust the daily alarm as shown in the following picture:

Alarm Clock and Wake-up Light Setting

The default clock time is AM 12:00 when you plug in the appliance for the first time.
Notice: The following operation should be operated step by step.

1. Alarm Hour Time Setting
   Press and hold the for at least 2S after the time display is on, the hour indicator in the display starts to flash, then rotate the + and — on snooze button to changes by one hour, press the to confirm and the minute indicator in the display blink at the same time.

2. Alarm Minute Time Setting
   Rotate the + and — on snooze button to changes by one minute after the minute indicator in the display starts to flash, press the to confirm and start to set wake-up sound at the same time.

3. Wake-up Sound Setting
   Rotate the + and – on snooze button to choose a wake-up sound from S01 to S08 and OFF, press the t0 confirm and start to set alarm volume.
   Notice: You can use wake-up sounds or the FM radio as a wake-up Sound. The Wake-up Light built-in 7 wake-up sounds (S01 – S07), S08 is FM radio. The corresponding icon appears on the display when you choose one.

4. Alarm Volume Setting
   Rotate the + and – on snooze button to adjust the volume from V01 to V16 (16 levels in total), then press the to confirm and start to set wake-up light intensity.

5. Wake-up Light Intensity Setting
   Rotate the + and — on snooze button to adjust the wake-up light intensity from LO1 to L20, press the to confirm and start to set the dawn duration time of the wake-up light.
   Notice: The screen displays show OFF, LO1 – L20 in turn. You can choose OFF if you don’t need light, while L20 chosen means light intensity increases gradually from LO1 to L20.

6. Dawn Duration Time of Wake-up Light
   The dawn duration time is the time in which the light intensity of the lamp gradually increases to the set level before the alarm sound is played.

The range of dawn duration time of the wake-up light is 10-60MIN, the dawn duration time can be changed by 10 minutes to your preference by rotating the

• or — on snooze button , press the to confirm and complete all the alarm clock and wake-up light profile setting.
  Note: You can not select Wake-up Sound and Wake-up Light to be “OFF” at the same time.

Snooze Function

The wake-up light turns on at the set time after alarm 1 or alarm2 activated, the light intensity increases to the set maximum light intensity before the alarm sound is played. The following operations are available when alarm sound is played, you can operate according to your requirement:

1. Snooze
   You can press the button to snooze for a while. The wake-up light and the alarm sound stop. After 9 minutes, the lamp turns on and the alarm sound is automatically played again. (User Tip: The number of snoozes is unlimited.)

2. Manually stop the alarm clock
   (1) Press the alarm1 or alarm2 if you want to turn off the current wake-up light and alarm sound when the alarm sound is played or the alarm is snoozed.
   Long press the snooze button for 3 seconds to turn off the alarm1 or alarm2 .

3. Automatically stop the alarm clock
   The current alarm sound and wake-up light stop automatically after 30 minutes if no any operation done.
   Note:
   1.The alarm 1 or alarm 2 icon flashes on the display when the alarm is snoozed.
   2.The alarm 1 or alarm 2 icon stays bright on the display, which means alarm 1 or alarm2 activated.

FM Radio Operation

For a good radio reception the wire antenna must be completely un-coiled. Adjust the antenna, whilst in radio operation, to the best reception.
Notice: The following operations should be operated step by step.

1. Switching on/off the radio
   Press the FM on/off button switch on/off the FM radio after the time display is on.

2. FM automatic scanning
   To scan radio frequencies automatically when the time display is on, press and hald the button for at least 2 seconds. The scanning range is from 76MHz to 108.0Mkz, the last scanned radio frequency will be on automatically after the all scanning is completed.

3. Manual station selection
   After FM automatic scanning has been completed from 76MHz to 108.0MHz, then press and hold down the button for 2S to adjust the last/next radio station.

4. Adjust the FM Radio Volume
   Click the button to increase or decrease the radio volume after the radio display icon is on.station.

5. FM Radio Manual Searching
   Rotate the + and — on SNOOZE button to manually adjust the FM frequency to change by 0.1MHZ after the radio display icon is on.

Relaxing Bedtime Sound Function

1. Switching on the relaxing bedtime sound function
   Press the button to switch on the relaxing bedtime sound function after the time display is on and the relaxing bedtime sound icon appears on the display.
   Then click the button to change sounds from S01 to S08, and click the  to adjust the sound volume.

2. Two ways to switch off the relaxing bedtime sound function
   (1)The relaxing bedtime sound function has 8 sounds: S01-S08, it will be turn off if you click button again when S08 sound set, the relaxing bedtime sound icon disappears from the display.
   (2)To switch off the relaxing bedtime sound function, press and hold down the button for 2 seconds. The relaxing bedtime sound icon disappears from the display.

The appliance has 3 light modes: wake-up light, mood light and RGB mood light. Please make sure the device is connected with the mains power supply and the time display is on before you are ready to do the following operations:

Light – Wake-up Light Mode

1. Press the button to switch on the wake-up light and use it as a bedside light.
2. You can adjust the light intensity by pressing the + and — buttons .
3. To switch off the wake-up light, press the button again.

Light – Mood Light Mode

1. Press and hold the button for at least 2S on the device to switch on the mood lighting.
2. Click the button to change the color of mood lighting. The LEDs light up in the following sequence: red → orange → yellow → green → blue → indigo → purple → etc.
3. You can adjust the mood light intensity by pressing the + and — buttons .
4. To switch off the mood light, press and hold the button for at least 2S again.

Light – RGB Mood Light Mode

1. Press the button to switch on the RGB mood light and use it as a mood light too.
2. Click the button to change the color of RGB mood lighting from C01 to C07. There are 7 different RGB lighting colors in total.
3. You can adjust the RGB mood light intensity by pressing the + and- buttons .
4. To switch off the RGB mood light, press and hold the button for at least 2S.

Fall Asleep Function

Notice: The following operation should be operated step by step.

1. Press the fall asleep button to switch on the fall asleep function after the time display is on.
2. The set fall asleep time appears on the display and flash for 5 seconds.
3. Rotate the + or — on the Snooze button to adjust the time (10 to 120, 180 or 240 minutes).
4. You can set the desired light (3 light modes are available) and/or FM radio, or light (3 light modes are available) and/or the relaxing bedtime sounds when you want the light and/or FM radio, or the light and/or the sound of the Wake-up Light to stay on during a set period of time (10 to 120, 180 or 240 minutes) before you go to sleep. The FM radio, lamp and/or sound switch off automati- cally after the set time.
5. You can track your remaining bedtime by clicking the button after the fall asleep function activated.
6. To switch off the fall asleep function, press and hold the fall asleep button for at least 2 seconds. The fall asleep icon disappears from the display

Time Display Brightness

You are able to control the brightness of the clock’s display manually according to your preferences. For example, you can change the brightness of the display so that intense light won’t wake you in the morning. There are 3 brightness level, click the button to adjust it after the time display is on. The time display turns off if you click the button once more when the time display brightness is at the maximum brightness.

Change Battery

Remove the screw from the battery case with a screwdriver insert the battery into the battery case, while the positiveelectrode is upward; insert the cover of battery case into theslot of battery case at the left side; tighten the battery case,

Contact us

If you have any sing problems with the product, please dorit be hesitant to contact us, we will be happy to help you solve various product problems so that you can get a better experience with products,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>