momcozy LM02 Kneading Lactation Massager with Heat User Manual
- May 15, 2024
- MOMCOZY
Table of Contents
KNEADING
LACTATION MASSAGER
LM02 Kneading Lactation Massager with Heat
IMPORTANT! READ AND FOLLOW THESE NSTRUCTIONS CAREFULLY AND KEEP THEM FOR
FUTURE REFERENCE.
WARNING
- This Kneading Lactation Massager is intended for ax single user. It is not recommended to rent or share.
- Do NOT allow anyone unfamiliar with this product to use it.
- Do NOT use f the charging cable or product s damaged. Contact our customer service team for an exchange.
- If the charging cable casing or wiring becomes loose, separated, or frayed, stop using the charging cable immediately and contact the device manufacturer.
- Parental or guardian supervision is required at all times f users have physical or ntellectual disabilities
- Do not clean or sterilize the product with a washing machine, microwave, or dishwashing machine.
- This kneading lactation massager is intended to help women overcome some breastfeeding challenges, like engorged breasts or clogged milk ducts. Please use it n strict accordance with the described purpose in this manual.
- Only use the charging cable that comes with the unit.
INDICATIONS FOR USE
Momcozy kneading lactation massager is intended to alleviate the pain and discomfort associated with breastfeeding, clogged ducts, engorgement, and mastitis. Moreover, t speeds up the let-down and milk flow.
PRODUCT OVERVIEW
PRODUCT DESCRIPTION
| Power/Vibration Control
Press and hold for 1.5 seconds to enter standby mode, and the indicator
remains solid white. This massager will change from 6 vibration patterns by
pressing the power button.
---|---
| Massage Ball Control
In standby mode, short press to activate the massage balls. This massager will
change from ow speed/medium speed/high speed/pause by pressing this button.
| Heat Control
In standby mode, short press to change from low heat (37 C )/medium heat ( 41
·c)/high heat (45 °C)/pause.
| Battery Indicator
In charging – the ndicator will be blinking white.
Fully charged – the indicator will be solid white.
n working – the indicator will be solid white. Low battery – the indicator
will be blinking white and go out when running out of battery.
CHARGING YOUR MASSAGER
- Connect the charging cable provided to the massager
- Plug the USB into a computer or USB adaptor(DC 5V 1.5A).
- The indicator will be blinking white while the massager is charging.
- The massager is fully charged when the ndicator remains solid white.
- It takes approximately 1.5 hours to get the device fully charged. Recharge the massager as needed.
HOW TO USE
- Use the massage balls to reach deeper into the breast ducts and gently massage the clogged area on the breast.
- Massage the clogged area on the breast with a comfortable vibration pattern.
- Allow a few minutes for the massager to reach full heat and warm the breast to stimulate milk flow.
- Massage the clogged area on the breast with the curved side, while moving towards the nipple.
Note:
- When heating, the device will change from high heat to ow heat after 20 minutes. t will shut off automati cally after heating for 30 minutes.
- It cannot be turned on when charging.
- Fully charge the battery before the first use.
- Allow a few minutes for the massager to reach full heat.
CARE AND STORAGE
- Always clean your massager before and after every use.
- Unplug from power source before cleaning.
- Clean with warm water.
- Do NOT submerge the massager in water.
- Allow the massager to air dry.
- Avoid direct sunlight.
- Store the massager in a clean and dust-free place.
**PRODUCT SPECIFICATION
**
Product Name: Kneading Lactation Massager
Model: LM02
Color: Red/Blue-Green
Net Weight: 150g
Input Voltage: DC5V 1.5A
Working Temperature: 0 °C to 47 °C
Storage Temperature: -10 °C to 60 °C
Product Size: 152 mm 55 mm 51 mm
Battery Capacity: 1200mAh
Packaging Size: 1768658 mm
FCC COMPLIANCE
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful nterference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful nterference to radio communications. However,
there s no guarantee that interference will not occur n a particular
installation.
If this equipment does cause harmful nterference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>