openGear OG-HDBT-EAPx Extenders & Receivers Board User Manual

: May 15, 2024
: Opengear

Table of Contents

openGear OG-HDBT-EAPx Extenders & Receivers Board
Product Information
Product Usage Instructions
- Dashboard Control
Warranty Information
What Is in The Box
Key Features
Specifications
Rear Modules
Dashboard Control
Appendix A
ABOUT COMPANY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

openGear OG-HDBT-EAPx Extenders & Receivers Board

openGear-OG-HDBT-EAPx-Extenders &-Receivers-Board-
fig-1

Product Information

Specifications

Description: HDBaseT Transmitter
Input: HDMI 1.4
Output: HDMI 1.4 loopout, RJ45 (HDBaseT)
RS-232: Inputs
IR: Input and output
Cable Reach: 100 meters on CAT6, 10 meters on HDMI 1.4

Product Usage Instructions

What Is in The Box
Ensure all components are present as listed in the product packaging.

Key Features
Highlight the key features of the product, such as HDBaseT transmission, HDMI input/output, and control options.

Specifications
Refer to the specifications listed above for detailed technical information on the product.

Rear Modules
Provide information on the rear modules of the product and their\ functions.

Dashboard Control

Getting Started
Introduction to the Dashboard software and how to quickly access and utilize its features.
Running Dashboard
Steps to download and install the Dashboard software from the provided link and how to run it.
OG-HDBT-EAPx Dashboard GUI
Overview of the Dashboard interface, highlighting product information displayed and signal status.

Warranty Information

Details on warranty coverage, repair options, and limitations based on the provided warranty statement.

What Is in The Box

OG-HDBT-EAPx-SET-1

1 x OG-HDBT-EAPx-MB
1 x OG-HDBT-EAPx-RM

Key Features

OGX/3.0 card-based form factor.
Dashboard control enabled.
HDBT transmitter
Supports HDMI 1.4 input and HDBT output
RS-232 inputs
HDCP 1.4compliant.
Low power consumption – less than 10 W.
5-year limited warranty

Specifications

Description	HDBaseT Transmitter
Input	HDMI 1.4
Output	HDMI 1.4 loopout, RJ45 (HDBaseT)
RS- 232	Inputs
IR	Input and output
Cable Reach	100 meters on CAT6, 10 meters on HDMI 1.4

Rear Modules

openGear-OG-HDBT-EAPx-Extenders &-Receivers-Board-
fig-2

Dashboard Control

Getting Started
The Dashboard software is design to allow you to quickly access the feature sets of openGear form factor cards on a simple User Interface. This section will help you get up and running as quickly as possible.

Running Dashboard

Before you can successfully run the Dashboard software for the first time you must first download it from https://www.opengear.tv/frame-and-control/control-system/download/.
Run the downloaded setup file and choose an appropriate installation location on your computer’s storage.
Now you can run the Dashboard by double clicking on the Dashboard icon.

OG-HDBT-EAPx Dashboard GUI

OG-HDBT-EAPx is a very straight forward plug and play card.
The Dashboard interface only allows identify its product name, software version, hardware version and firmware versions as well as the link status of the incoming and outgoing signals.

openGear-OG-HDBT-EAPx-Extenders &-Receivers-Board-
fig-3

Appendix A

COPYRIGHT, TRADEMARK, and REGISTRATION

All rights reserved by APANTAC LCC, Beaverton, Oregon, USA. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. They will be incorporated in subsequent editions. The product manufacturer may make improvements and/or changes in the product described in this document at any time.
All other trademark(s), copyright(s), and registered technologies mentioned in this document are the properties of their repective owner(s).

WARRANTY STATEMENT

Apantac LLC (herein after referred to as “Apantac”) warrants to the original purchaser of the products manufactured by Apantac (the “Product,”) will be free from defects in material and workmanship for a period of three (3) years from the date of shipment of the Product to the purchaser.
If the Product proves to be defective during the three (3) year warranty period, the purchaser’s exclusive remedy and Apantac’s sole obligation under this warranty is expressly limited, at Apantac’s sole option, to:
- repair the defective Product without charge for parts and labor or,
- provide a replacement in exchange for the defective Product or,
- if after a reasonable time, is unable to correct the defect or provide a replacement Product in good working order, then the purchaser shall be entitled to recover damages subject to the limitation of liability set forth below.

Limitation of Liability

Apantac’s liability under this warranty shall not exceed the purchase price paid for the defective product. In no event shall Apantac be liable for any incidental, special or consequential damages, including without limitation, loss of profits for any breach of this warranty.
If Apantac replaces the defective Product with a replacement Product as provided under the terms of this Warranty, in no event will the term of the warranty on the replacement Product exceed the number of months remaining on the warranty covering the defective Product.
Equipment manufactured by other suppliers and supplied by Apantac carries the respective manufacturer’s warranty. Apantac assumes no warranty responsibility either expressed or implied for equipment manufactured by others and supplied by Apantac.
This hardware warranty shall not apply to any defect, failure, or damage:
- Caused by improper use of the Product or inadequate maintenance and care of the Product.
- Resulting from attempts by those other than Apantac representatives to install, repair, or service the Product.
- Caused by installation of the Product in a hostile operating environment or connection of the Product to incompatible equipment.