reolink Argus PT Lite 3MP Pan and Tilt Wire Free Camera User Guide
- May 15, 2024
- reolink
Table of Contents
Argus PT Lite 3MP Pan and Tilt Wire Free Camera
Argus PT Lite 3MP Pan and
Tilt Wire Free Camera
User Guide Argus PT Lite
Quick Start Guide
What’s in the Box
Camera Introduction
1.Lens
2. 6 IR LEDs
3. Daylight Sensor
4. Built-in PIR Sensor
5. Built-in Mic
6. Status LED
7. Speaker
8. Reset Hole
- Press for more than five seconds to restore the device to default settings.| 9. Micro SD Card Slot
- Rotate the camera’s lens to find the reset hole and the SD card slot.
10. Power Switch
11. Antenna
12. Charging Port
13. Battery Status LED
---|---
Different states of the status LED:
Red Light: WiFi connection failed
Blue Light: WiFi connection succeeded| Blinking: Standby status
On: Working status
---|---
Set up the Camera
Set up the Camera Using a Smartphone
Step 1 Scan to download the Reolink App from the App Store or Google Play
store.
https://reolink.com/wp-json/reo-v2/app/download
Step 2 Turn on the power switch to power on the camera.
Step 3 Launch the Reolink App, click the “ ” button in the top right corner to add the camera. Scan the QR code on the device and follow the onscreen instructions to finish initial setup.
Set up the Camera on PC (Optional)
Step 1 Download and install the Reolink Client: Go to https://reolink.com
Support > App&Client.
Step 2 Launch the Reolink Client, click the “ ” button, input the UID code of the camera to add it and follow the onscreen instructions to finish initial setup.
Charge the Camera
It’s recommended to fully charge the battery before mounting the camera.
Charge the battery with a power adapter. (not included) Charge the battery
with the Reolink Solar Panel (Not included if you only purchase the camera).
Charging Indicator:
Orange LED: Charing
Green LED: Fully charged
For better weatherproof performance, please always cover the charging port with the rubber plug after charging the battery.
Install the Camera
Notes on Camera Installation Position
- The camera MUST be installed upside down for better waterproof performance and better PIR motion sensor’s efficiency.
- Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the PIR motion sensor.
- For better motion detection performance, please install the camera angularly.
NOTE: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.
Mount the Camera
Drill holes in accordance with the mounting hole template and screw the camera bracket to the wall.
Install the antenna to the camera.
NOTE: Use the drywall anchors included in the package if needed.
Align the white hole on the camera top with the white hollow screw on the
bracket. Use a wrench and a hex head screw provided to secure the camera into
place. Then cover the rubber plug.
Mount the Camera to Ceiling Install
the mount base to the ceiling. Align the camera with the mount base and turn
the camera unit clockwise to lock it in position.
Install the Camera with Loop Strap
You are allowed to strap the camera to a tree with both the security mount and
ceiling bracket. Thread the provided strap to the plate and fasten it to a
tree. Next, attach the camera to the plate and you are good to go.
Safety Instructions of Battery Usage
The camera is not designed for running 24/7 at full capacity or around-the- clock live streaming. It’s designed to record motion events and to live view remotely only when you need it. Learn useful tips on how to extend the battery life in this post: https://support.reolink.com/hc/en- us/articles/360006991893
- Do not remove a built-in battery from the camera.
- Charge the battery with a standard and high-quality DC 5V battery charger or Reolink solar panel. It’s not compatible with solar panels from any other brands.
- Charge the battery only if in temperatures between 0°C and 45°C. The battery is intended for use only in temperatures between -10°C and 55°C.
- Keep the charging port dry, clean and free of any debris. Cover it with the rubber plug after the battery is fully charged.
- Do not charge, use or store the battery next to areas that may become hot. Examples include, but are not limited to, on or near a space heater, cooking surface, cooking appliance, iron, radiator, or fireplace.
- Do not use the battery if its case appears damaged, swollen, or compromised. Examples include, but are not limited to, leaking, odors, dents, corrosion, rust, cracks, swelling, melting, and scratches.
- Always follow the local waste and recycling laws to dispose of used batteries.
Troubleshooting
Camera is Not Powering On
If your camera is not powering on, please try the following solutions:
- Make sure the power switch is turned on.
- Charge the battery with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged
If these won’t work, contact Reolink Support.
Failed to Scan QR Code on the Phone
If you cannot scan the QR code on your phone, please try the following
solutions:
- Remove the protective film from the camera lens.
- Wipe the camera lens with a dry paper/ towel/tissue.
- Vary the distance between your camera and the mobile phone so that the camera can focus better.
- Try to scan the QR code under sufficient lighting.
If these won’t work, contact Reolink Support.
Specification
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Dimensions: 98 x 122mm
Weight: 472g
For more specifications, visit the Reolink official website.
Notification of Compliance
CE Declaration of Conformity
Reolink declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU and
Directive 2014/30/EU.
UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Radio Equipment
Regulations 2017 and Electromagnetic Compatibility Regulations 2016.
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Compliance Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes.throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Official Store or a Reolink authorized reseller. Learn
more: https://reolink.com/warranty-and-return/.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of reach of children.
WiFi Operating Frequency
OPERATING FREQUENCY : (the maximum transmitted power) 2.4GHz: (For 2.4GHz
camera only): 2412MHz — 2472MHz ( EIRP < 20 dBm )
Technical Support
If you need any technical help, please visit our official support site and
contact our support team before returning the products,
https://support.reolink.com.
@ReolinkTech https://reolink.com
58.03.001.0325
Documents / Resources
|
reolink Argus PT Lite 3MP Pan and Tilt Wire Free
Camera
[pdf] User Guide
Argus PT Lite 3MP Pan and Tilt Wire Free Camera, Argus PT Lite, 3MP Pan and
Tilt Wire Free Camera, Tilt Wire Free Camera, Wire Free Camera, Free Camera
---|---
References
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Official: Security Cameras and Systems for Home & Business
- Warranty & Return – Reolink
- Reolink Support - Official Reolink Help Center
- How to Extend the Battery Life of Reolink Battery Powered Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>