Lordear Floating Bathroom Sink Wall Mounted Corner Sink Instruction Manual

: May 15, 2024
: LORDEAR

Table of Contents

Product View
Safety Information
Warranty
Pre-Installation
HARDWARE INCLUDED
TOOLS REQUIRED
Installation
Care and Cleaning
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lordear Floating Bathroom Sink Wall Mounted Corner Sink

Product View

THANK YOU

We appreciate the trust and confidence you have placed in Lordear through the purchase of this sink. We strive to continually create quality products designed to enhance your home. Thank you for choosing us!

Safety Information

Before installing this sink, read this instruction manual carefully. It contains important information concerning the safe installation, operation, and maintenance of your sink.
Retain this manual for future use. In the event of sale, transfer, or relocation, ensure this manual remains with the sink.

WARNING: Keep all packaging materials out of the reach of children to prevent possible choking or suffocation.

WARNING: Handle with care. Vitreous chinaware is glass-like with sharp edges if broken. Do not drop, handle roughly, or overtighten bolts.

Warranty

LIMITED LIFETIME WARRANTY

Lordear products are manufactured with superior quality standards and workmanship and are backed by our limited lifetime warranty.
Lordear products are warranted to the original consumer purchaser to be free of defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.

Pre-Installation

Compare all parts with the Hardware Included and Package Contents lists in this manual.
Check the surface of the sink for any flaws or damage, including dents, bends, bumps, or scuff marks. If any damage is noticed or parts are missing, do not proceed with the installation. Contact the Lordear Customer Service Team.

Packing list

Part	Item	Quantity
A	sink	1
B	setscrew set	2
C	Use and care manual	1

HARDWARE INCLUDED

x2 Hanger bolts (8mm)
x2 washer
x2 nuts
x2 wall anchor
x2 Insulation sleeve

TOOLS REQUIRED

goggles
Drill
5/16″diamond drill bit
Tape
Ruler
Sealant
Flat Shovel
Philips screwdriver
Flat screwdriver
Wrench
Pipe Wrench
Expoxy

IMPORTANT: LORDEAR strongly recommends that this product be installed by a licensed plumber. Ensure that installation complies with applicable plumbing and building codes.

Installation

Prepare Location
Locate studs in the wall. If the studs do not line up with the holes in the back of the sink, be sure to add sufficient wall supports behind the finished wall.
Install Hanger Bolts
Measure the distance between mounting holes in the back of the sink. Drill pilot holes in wood and screw in hanger bolts. Check postion with a level.
Step 1： Drill two holes to a depth of 75mm in the required position on the wall by using a 14mm masonry drill bit.

Step 2： Push a wall plug into each hole

Step 3： Screw the fixing bolt into each fixing plug by using a 8mm spanner until the spanner contacts the wall.

Secure Sink With Washers and Nuts
Screw the sink onto the two hanger bolts.
Secure the sink with insulating sleeves, washers and nuts. Be careful not to over-tighten the bolts. Overtightening can cause the sink to chip and crack.
Apply Caulking
Finish the sink installation by applying a bead of caulk between the sink and the wall.
Sink Accessories
Complete your installation by adding the preferred plumbing accessories, such as the faucet, click-clack drain, p-trap and angle valves to your sink.

Care and Cleaning

For best results in caring for your sink, we suggest the following:

Clean the outside surface with mild soap, warm water, and a soft cloth.
On stubborn stains, use a powdered detergent and damp sponge or nylon scouring pad.
Never use abrasive scouring powders, cleansers, or pads because they will scratch, damage, and dull the surface.