KLEEN TOOLS MT7 Pro Disc Brake and Lever Instruction Manual
- May 15, 2024
- KLEEN TOOLS
Table of Contents
INSTALLATION MANUAL
FOR MOUNT TYPE 7
We know you want to jump right
into installation, but read me first!
MT7 Pro Disc Brake and Lever
Read instructions carefully before assembling and installing
PLEASE USE CAUTION
Kleen Opener has metal prongs that can cut your hands if not careful!
DO NOT USE KLEEN OPENER
TO MOVE DUMPSTER
Misuse of this product can cause breakage and/or personal harm.
For questions or comments please coll us at:
1 (818) 280 3907
or e-mail us at: owner@firmfresh.com
Visit us at: kleentools.com
PACKAGE CONTENTS
Please review the contents of your Kleen Opener to ensure all parts are ready
[DO NOT REMOVE THE ZIP-TIE UNTIL INSTRUCTED]
ANATOMY OF A KLEEN OPENER
GENERAL INSTALLATION:
Assembling the Arm
Kit comes with LEFT & RIGHT side assemblies. Prior to installing Kleen Openers
on the dumpster, the adjusting channel should be set into the adjusting tube
to secure it during mounting.
Mounting the Bracket
Identify your dumspter sides from the front. Lift lid up all the way so it rests on the back of the dumpster. Installation is the same for left & right sides.
Prior to mounting, ensure 1/2″ bolts are unscrewed enough so bolt ends and
Compression Bracket are flush with the inside of the Mounting Bracket.
Hold Kleen Opener assembly by Adjustment Tube. With one hand holding the Compression Bracket out of the way of TOP RAIL, position mounting bracket at an angle. Then move bracket down to ensure it is FLAT with TOP RAIL and lower L shaped Bracket is below bottom outer edge of Dumpster’s Top Rail.
With Hand Tightening or 3/4″ Sockiet, fasten bolts until Compression Bracket
Prongs are evenly in contact with siding.
Apply Red Threadlocker to about 3 threads on each bolt behind the Compression
Bracket.
Continue fastening bolts with 3/4″ Socket, being sure to alternate between each bolt to ensure even pressure. Tighten until Compression Bracket Prongs are firmly pressed into sides of dumpster. Give one final 1/4 turn to securely fasten.
Adjusting Arm Length
[YOU CAN NOW SAFELY CUT THE ZIP-TIE]
OPERATIONAL GUIDE
After installation, lift arm up using guide below, place lid onto the arm and close using Nylon Strap, like shown below.
To open dumpster lid, lift strap UP 6″ to 8″ until gas spring takes over and opens remainder of the way.
To close dumpster lid, pull strap TOWARDS you and DOWN until the lid is closed entirely. You can let go of the strap at this point.
TROUBLESHOOTING
I’m missing parts listed in the Package Contents
Please refer to Page 1 and contact us immediately!
I think I have the wrong version for my dumpster
Please refer to Page 1 and contact us immediately!
My set screw isn’t threading into the adjusting tube
The alignment between the Adjusting Channel and the Adjusting Tube holes may
need slight adjustment to fully engage the ‘K” x 1.5″ Adjusting Channel Set
Screw to fully engage the Adjusting Tube threads.
My bracket doesnt fit my dumpster
Ensure mount type ordered matches the dumpster you are installing it on.
Please prefer to Page 1 and contact us immediately if you chose the wrong
mount type.
Kleen Opener isn’t sitting correctly on my dumpster
Ensure bracket is flush with top rail and double check your mount type is
appropriate for your dumpster style.
Strap won’t reach the front and lid doesn’t open easily
Check that the Kleen Opener distance from the dumpster rear wall is
appropriate for the size of your dumpster. Refer to the distance guide on Page
5.
Kleen Opener is too loose or crooked after securing bolts
Ensure bolts were tightened enough, and tightening was performed alternating
between both bolts for even pressure and alignment
If you are having difficulty setting length of arm, press the Extend Buttons
first, pull, and then let go of the buttons to let the device snap into its
index hole.
Arm doesn’t reach 2-4″ distance from front
Check install depth from back wall is appropriate for your size dumpster. If
need be, you can move the Kleen Opener 2″ – 8″ towards the front of the
dumpster.
Kleen Opener wont engage gas spring to open lid
If lifting 6″ – 8″ inches and the gas spring does not engage, your lid may be
too heavy for the current spring. Please refer to Page 1 and contact us
immediately!
SEE OUR INSTALLATION VIDEO
https://kleentools.com/pages/mt7-install-video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>