KLEEN TOOLS MT1 Ac Outdoor Lifting Stand Installation Guide

KLEEN TOOLS MT1 Ac Outdoor Lifting Stand

OVERVIEW

PACKAGE CONTENTS

Please review the contents of your Kleen Opener to ensure all parts are ready

[DO NOT REMOVE THE ZIP-TIE UNTIL INSTRUCTED]

ANATOMY OF A KLEEN OPENER

GENERAL INSTALLATION

Assembling the Arm

• Kit comes with LEFT & RIGHT side assemblies. Before installing
• Kleen Openers on the dumpster, the adjusting channel should be set into the adjusting tube to secure it during mounting.

Mounting the Bracket

• Identify your dumpster sides from the front. Lift the lid all the way so it rests on the back of the dumpster. Installation is the same for left & right sides.
• Hold the Kleen Opener Assembly by the Adjusting Tube. Ensure the mounting bracket’s inner screws are positioned up against the lower angle of the Dumpster’s inner wall. Position the mounting bracket as close to level with Top Rail. If Dumpster’s Top Rail is damaged or is not level, you can adjust the Top Leveling Screw to adjust the mounting bracket to help level the Mounting Bracket. (See Step 5)
• Lightly fasten cone point bolts with 1/4″ Hex Drive until the tip is in contact with the dumpster’s side. If the mounting bracket is not level turn the Leveling Screw clockwise with the 5/32″ Hex Drive until Mounting Bracket is level and aligned with Top Rail
• Appy Red Threadlocker to about 3 threads on each Cone Point bolt.
• Continue fasting the Cone Point Bolts with the 1/4″ Hex Drive, being sure to alternate between each bolt to ensure even pressure and alignment. Tighten until Cone Point Bolts are firmly pressed in the side of the Dumpster.
• Then give one final ¼ turn to securely fasten.

Adjusting Arm Length

[YOU CAN NOW SAFELY CUT THE ZIP-TIE]

OPERATIONAL GUIDE

After installation, lift the arm using the guide below, place the lid onto the arm and close using a Nylon Strap, as shown below.

• To open the dumpster lid, lift the strap 6″ to 8″ until the gas spring takes over and opens the remainder of the way.
• To close the dumpster lid, pull the strap TOWARDS you and DOWN until the lid is closed entirely. You can let go of the strap at this point.

TROUBLESHOOTING

• I’m missing parts listed in the Package Contents
  • Please refer to Page 1 and contact us immediately!
• I think I have the wrong version for my dumpster
  • Please refer to Page 1 and contact us immediately!
• My set screw isn’t threading into the adjusting tube
  • The alignment between the Adjusting Channel and the Adjusting Tube holes may need slight adjustment to fully engage the ¼” x 1.5″ Adjusting Channel Set Screw to fully engage the Adjusting Tube threads.
• My bracket doesn’t fit my dumpster
  • Ensure the Kleen Opener’s Mount Type is the correct one for the Dumpster you are installing it on. Please refer to Page I and contact us Immediately.
• The Kleen Opener isn’t sitting correctly on my dumpster
  • Ensure the bracket is flush with the top rail and double-check check your mount type is appropriate for your dumpster style.
• The strap won’t reach the front and the lid doesn’t open easily
  • Check that the Kleen Opener distance from the dumpster’s rear wall is appropriate for the size of your dumpster. Refer to the distance guide.
• The Kleen Opener is too loose or crooked after securing the bolts
  • Ensure the Mounting Bracket’s Cone Point Bolts were tightened enough, and tightening was performed alternating between both bolts for even pressure and alignment. In addition, we provide a ¼” x 0.5″ levelling screw on top of the Mounting bracket that may be used to help level the Mounting Bracket if the Top Rail of the Dumpster, where the Kleen Opener Assembly is being mounted, is not level.
• The arm doesn’t reach 2-4″ distance from the front
  • Check install depth from the back wall is appropriate for your size dumpster. If need be, you can move the Kleen Opener 2″ – 8″ towards the front of the dumpster.
• The Kleen Opener won’t engage the gas spring to open the lid
  • If lifting 6″ – 8″ inches and the gas spring does not engage, your lid may be too heavy for the current spring. Please refer to Page 1 and contact us immediately!
• Does the Adjusting Screw located on Top of the Kleen Opener Mounting Bracket always need to be adjusted to level the Kleen Opener Assembly?
  • No, we provided a ¼” x 0.5″ leveling
    screw on top of the Mounting bracket as a new feature to the Kleen Opener Mounting Bracket; as some Dumpsters’ Top Rail, where the Kleen Opener is mounted, are damaged or not level. The Adjusting Screw may be used to help level and align the Mounting Bracket.

SEE OUR INSTALLATION VIDEO

We know you want to jump right into installation but read me first!

@kleentools

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>