KLEEN TOOLS MT5 Type 5 Mount Instruction Manual
- May 15, 2024
- KLEEN TOOLS
Table of Contents
KLEEN TOOLS MT5 Type 5 Mount
INSTRUCTION MANUAL
We know you want to jump right into installation, but read me first!
Read instructions carefully before assembling and installing
Use caution when handling the Kleen Opener during unpacking, assembly, and
installation. Kleen Opener has metal edges that can cause harm.
Misuse of this product can cause breakage and/or personal harm.
DO NOT USE KLEEN OPENER
TO MOVE DUMPSTER
For questions or comments please call us at: 1 (818) 280 3907
or e-mail us at: owner@firmfresh.com
Visit us at: kleentools.com
PACKAGE CONTENTS
Please review the contents of your Kleen Opener to ensure all parts are ready
ANATOMY OF A KLEEN OPENER
GENERAL INSTALLATION:
Assembling the Arm
Kit comes with LEFT & RIGHT side assemblies. Prior to installing Kleen Openers on the dumpster, the adjusting channel should be set into the adjusting tube to secure it during mounting.
GENERAL INSTALLATION:
Mounting the Bracket
Mounting the Bracket
Then give one final ¼ turn to securely fasten.
Adjusting Arm Length
[YOU CAN NOW SAFELY CUT THE ZIP-TIE]
OPERATIONAL GUIDE
After installation, lift arm up using guide below, place lid onto the arm and close using Nylon Strap, like shown below.
To open dumpster lid, lift strap UP 6″ to 8″ until gas spring takes over and opens remainder of the way.
To close dumpster lid, pull strap TOWARDS you and DOWN until the lid is closed entirely. You can let go of the strap at this point.
TROUBLESHOOTING
I’m missing parts listed in the Package Contents
Please refer to Page 1 and contact us immediately!
I think I have the wrong version for my dumpster
Please refer to Page 1 and contact us immediately!
My set screw isn’t threading into the adjusting tube
The alignment between the Adjusting Channel and the Adjusting Tube holes may
need slight adjustment to fully engage the¼” x 1.5″ Adjusting Channel Set
Screw to fully engage the Adjusting Tube threads.
My bracket doesnt fit my dumpster
Ensure the Kleen Opener’s Mount Type is the correct for the Dumpster you are
installing it on. Please refer to Page I and contact us Immediately.
Kleen Opener isn’t sitting correctly on my dumpster
Ensure bracket is flush with top rail and double check your mount type is
appropriate for your dumpster style.
Strap won’t reach the front and lid doesn’t open easily
Check that the Kleen Opener distance from the dumpster rear wall is
appropriate for the size of your dumpster. Refer to the distance guide on Page
5.
Kleen Opener is too loose or crooked after securing bolts
Ensure the Mounting Bracket’s Cone Point Bolts were tightened enough, and
tightening was performed alternating between both bolts for even pressure and
alignment. In addition, we provide a ¼11 x 0.511 leveling screw on top of the
Mounting bracket that may be used to help level the Mounting Bracket if the
Top Rail of the Dumpster, where the Kleen Opener Assembly is being mounted, is
not level.
Arm doesn’t reach 2-4″ distance from front
Check install depth from back wall is appropriate for your size dumpster. If
need be, you can move the Kleen Opener 211 – 811 towards the front of the
dumpster.
Kleen Opener wont engage gas spring to open lid
If lifting 611 – 811 inches and the gas spring does not engage, your lid may
be too heavy for the current spring. Please refer to Page 1 and contact us
immediately!
Does the Adjusting Screw located on Top of the Kleen Opener
Mounting Bracket always need to be adjusted to level the Kleen Opener
Assembly? No, we provided a ¼11 x 0.511 leveling screw on top of the Mounting
bracket as a new feature to the Kleen Opener Mounting Bracket; as some
Dumpsters’ Top Rail, where the Kleen Opener is mounted, are damaged or not
level.
The Adjusting Screw may be used to help level and align the Mounting Bracket.
SEE OUR INSTALLATION VIDEO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>