SUNBRITE SB-AW-SNDBR-S-B Sound Bar Instruction Manual

May 15, 2024
SUNBRITE

SUNBRITE logo

INSTALLATION MANUAL
SB-AW-SNDBR-X-B

SUNBRITE SB-AW-SNDBR-S-B Sound Bar

INTRODUCTION

We appreciate your purchase and are committed to providing the highest-quality products possible.
The SunBrite™ Outdoor Sound bar models are a superb choice for almost every type of home theater or home audio installation. They have been designed with advanced technological components that allow for high performance and a lifetime of enjoyment.

IMPORTANT INSTRUCTIONS AND CONSIDERATIONS
Read and understand all instructions. Before beginning installation, carefully plan location accounting for potential electrical, plumbing or other obstacles.
RECOMMENDED AMPLIFIER POWER
To get the best performance from the Sound bar when used with a Veranda Series SunBriteTV®, an amplifier or receiver with a power rating between 20 and 90 Watts RMS per channel is recommended: The Signature and Pro Series SunBriteTVs have an internal amplifier that can be used to drive the soundbar.
SPEAKER WIRE
To connect the Sound bar to an AV Receiver or Amplifier, high-quality 14 to 16 gauge stranded speaker wire is recommended. The wire may be connected directly to the speaker’s binding posts. Remember that you will need 2 runs of speaker wire to the Sound bar location as it contains the left and right speaker. Use the included DIN cable to connect the soundbar to a SunBriteTV. See page 5 for more information.

CONTENTS
SB-AW-SNDBR-S-B

  • (1) DIN cable w/90 cm cable for compatible SunBriteTVs

  • (1) DIN Cable to 3.5mm adapter for SunBrite Veranda TV’s

  • (1) Speaker Mount Bracket Small

  • (4) 1/4-20 x .25” Screws

  • (4) 1/4-20 Flat Washers
    SB-AW-SNDBR-M-B

  • (1) DIN cable w/90 cm cable for compatible SunBriteTVs

  • (1) DIN Cable to 3.5mm adapter for SunBrite Veranda TV’s

  • (1) Speaker Mount Bracket Large

  • (2) 1/2” threaded standoff

  • (2) 7/8” threaded standoff

  • (4) 1/4-20 x .25” Screws

  • (4) 1/4-20 Flat Washers

  • (4) 6/8MM X 20MM Black Nylon non-threaded spacers

  • (4) 1/4-20 x 1.25” Screws

INSTALLATION

SPEAKER PLACEMENT
The SB-AW-SNDBR-S-B and SB-AW-SNDBR-M-B are designed to be the Left and Right speakers of a sound system. For most applications, placement should be below a flat screen TV using the included mounting bracket.
Installing on a SunBriteTV
Mount the SB-AW-SNDBR-S-B, and SB-AW-SNDBR-M-B directly above or below Signature and Pro Series SunBriteTVs and below Veranda Series SunBriteTVs with the included bracket. The bracket attaches the soundbar using spacers or directly to the TV.
To determine which installation diagram to use for your SunBrite TV, refer to the table below.
NOTE: The Strong™ universal bracket SM-SBAR-BKT-UNIV (available separately) should be used when attaching the soundbar to any display other than a SunBriteTV.

Veranda 3: 4K HDR Series Smart

Size Model| Premium Speaker Bar| Installation
(55”) SB-V3-55-4KHDR-BL| SB-AW-SNDBR-M-B| Figure B
(65”) SB-V3-65-4KHDR-BL| SB-AW-SNDBR-M-B| Figure B
(75”) SB-V3-75-4KHDR-BL| SB-AW-SNDBR-M-B| Figure B
Veranda 2: 4K HDR Series
Size Model| Premium Speaker Bar| Installation
(43”) SB-V-43-4KHDR| SB-AW-SNDBR-S-B| Figure A
(55”) SB-V-55-4KHDR| SB-AW-SNDBR-M-B| Figure B
(65”) SB-V-65-4KHDR| SB-AW-SNDBR-M-B| Figure B
(75”) SB-V-75-4KHDR| SB-AW-SNDBR-M-B| Figure B
Signature 2: 4K HDR Series
Size Model| Premium Speaker Bar| Installation
(43″) SB-SE-43-4K| SB-AW-SNDBR-S-B| Figure A
(43″) SB-S2-43-4K| SB-AW-SNDBR-S-B| Figure A
(55″) SB-S2-55-4K| SB-AW-SNDBR-M-B| Figure B
(65″) SB-S2-65-4K| SB-AW-SNDBR-M-B| Figure B
(75″) SB-S2-75-4K| SB-AW-SNDBR-M-B| Figure B
Pro 2 Series
Size Model| Premium Speaker Bar| Installation
(32″) SB-P2-32-1K| N/A| N/A
(43″) SB-P2-43-1K| SB-AW-SNDBR-S-B| Figure A
(49″) SB-P2-49-4K| N/A| N/A
(55″) SB-P2-55-4K| SB-AW-SNDBR-M-B| Figure C
(65″) SB-P2-65-4K| SB-AW-SNDBR-M-B| Figure C

Figure A: Installation using no spacers

SUNBRITE SB-AW-SNDBR-S-B Sound Bar - Figure A

  1. Locate and remove the display screws from the display.
  2. Set the bracket in place against the display and replace the screws to secure.
  3. Remove the thumb screws from the sound bar and set it in place against the bracket.
  4. Replace the thumb screws to secure the soundbar to the bracket.

Figure B: Installation using display spacers

SUNBRITE SB-AW-SNDBR-S-B Sound Bar - Figure B

  1. Locate and remove the display screws from the display.
  2. Screw the spacers into the display.
  3. Set the bracket in place against the spacers and, using the display screws removed in Step 1, secure the bracket to the spacers.
  4. Remove the thumb screws from the sound bar and set it in place against the bracket.
  5. Replace the thumb screws to secure the soundbar to the bracket.

Figure C: Installation using soundbar spacers

SUNBRITE SB-AW-SNDBR-S-B Sound Bar - Figure C

  1. Locate and remove the display screws from the display.
  2. Set the bracket in place against the display. Using the display screws removed in Step 1, secure the bracket to the display.
  3. Remove the screws from the soundbar.
  4. Insert the soundbar screws (removed in Step 3) into the bracket and place the spacers on the screws.
  5. Set the soundbar in place against the spacers.
  6. Fasten the screws to secure the soundbar to the bracket.

CONNECTING AND CALIBRATING

Proper connections are important to the performance of any speaker within an audio system.
Performing the following steps will ensure proper connections for optimum speaker performance:

  1. At each speaker connection, ensure that the outer jacket is separated by at least 2 inches.

  2. Strip the insulation on each conductor approximately ¼” and insert into the speaker terminals.
    • Ensure that there are no stray strands of wire protruding from the connectors.
    • Observe proper polarity (+ to + and – to – ) for each speaker and at the amplifier).

  3. Turn on the home theater receiver and calibrate all speakers in the system according to the receiver (or surround processor) manufacturer’s instructions.

Connecting to a SunBriteTV
Connect the sound bar to Signature and Pro Model SunBriteTVs using the included 5 pin male connector wire (DIN Cable). Connect the wire ends as shown in the diagram below. Veranda Models will require an addtional 3.5mm 4 wire to DIN adapter, included.

SUNBRITE SB-AW-SNDBR-S-B Sound Bar - Figure D

SUNBRITE SB-AW-SNDBR-S-B Sound Bar - Figure F

When connecting the sound bar to a SunBrite Veranda TV, the DIN to 3.5 mm adapter must also be used. The 3.5 mm side attaches to the audio output of the Veranda TV, and the DIN connector side attaches to the DIN cable adapter, shown above. Then, connect the DIN cable adapter to the speaker inputs of the sound bar as indicated.

Verifying Phase
When proper polarity is not maintained, the speakers play at the opposite ‘time’ from each other, or out of phase. The result is audio with lack of bass and vocals that sound thin or distant. If during or after calibrating your receiver you suspect the sound is not right and you cannot see any markings on the wire to verify polarity is correct, try this simple test:

  1. Sit in the normal listening position for the system.

  2. Play some music with your receiver set to Mono.

  3. Listen to the music and observe the audio.
    • Does the bass sound full and even with the other audio?
    • Do the vocals sound centered and even in volume?
    If either of the answers are YES, follow steps 3 and 4 with any other speakers in the system.

  4. Turn off your receiver and reverse the connections for one of the speakers.

  5. Repeat your test at the same volume level. When the sound has the loudest and best sounding bass, and vocals are centered and clear, your connections are correct and in-phase.

CLEANING

Use a dampened soft cloth or paper towel to clean the cabinet. The grill is best
cleaned by brushing it off with a lint-free cloth.

SPECIFICATIONS

Product SB-AW-SNDBR-S-B SB-AW-SNDBR-M-B
Frequency response 100 Hz-22 kHz 95 Hz-22 kHz
Color Black Black
Connectors Gold-Plated Push Terminals Gold-Plated Push Terminals
Dimensions (WxHxD) 39” x 3.92” x 3” 49.5” x 3.92” x 3”
Sold as Each Each
Weight 11.5 lbs 13.2 lbs
Crossover Frequency 2.3 kHz 2.3 kHz
Speaker Grille Fixed Metal Fixed Metal
Nominal Impedance 8 Ohm 8 Ohm
Power Peak 225W 225W
Power RMS 90W 90W
Sensitivity 90 dB 90 dB
Tweeter 1” Pure Titanium Dome 1” Pure Titanium Dome
Voice Coil High Temp Voice Coil High Temp Voice Coil
Woofer Per Channel- 2 x 3” Titanium Vapor Deposit Polypropylene Cone Per

Channel- 2 x 3” Titanium Vapor Deposit Polypropylene Cone
Passive Radiator| 2 x Titanium Vapor Deposit Polypropylene Cone| 3 x Titanium Vapor Deposit Polypropylene Cone

TROUBLESHOOTING

These speakers are designed to function trouble-free. Most problems that occur are due to simple issues. If having trouble, contact Technical Support at 866-838-5052.

WARRANTY

Limited Lifetime Warranty
SunBriteTV Sound bar Speakers have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled.
Products to be repaired under this warranty must be returned to a designated service center with prior notification and an assigned return authorization number (RA).
CONTACTING TECHNICAL SUPPORT
As a thank you for purchasing SunBriteTV Electronics products, direct technical support services are available via phone. We encourage you to use this resource for any questions or concerns about our products. Visit our website for more support documentation.
866 838-5052 SunBriteTV.com

Copyright ©2024, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. SunBriteTV is also a registered trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice.

20240213mk
Support 866.838.5052

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals