SUNBRITE SB-AW-SNDBR-X-B 2 Channel Passive Soundbar Instruction Manual
- June 9, 2024
- SUNBRITE
Table of Contents
- INTRODUCTION
- IMPORTANT INSTRUCTIONS AND CONSIDERATIONS
- RECOMMENDED AMPLIFIER POWER
- SPEAKER WIRE
- CONTENTS
- INSTALLATION
- CONNECTING AND CALIBRATING
- CLEANING
- SPECIFICATIONS
- TROUBLESHOOTING
- WARRANTY
- CONTACTING TECHNICAL SUPPORT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SUNBRITE SB-AW-SNDBR-X-B 2 Channel Passive Sound bar Instruction Manual
INTRODUCTION
We appreciate your purchase and are committed to providing the highest quality products possible. The Sun Brite™ Outdoor Sound bar models are a superb choice for almost every type of home theater or home audio installation. They have been designed with advanced technological components that allow for high performance and a lifetime of enjoyment.
IMPORTANT INSTRUCTIONS AND CONSIDERATIONS
Read and understand all instructions. Before beginning installation, carefully plan location accounting for potential electrical, plumbing or other obstacles.
RECOMMENDED AMPLIFIER POWER
To get the best performance from the Sound bar when used with a Veranda Series Sun Brite TV®, an amplifier or receiver with a power rating between 20 and 90 Watts RMS per channel is recommended: The Signature and Pro Series Sun Brite TVs have an internal amplifier that can be used to drive the sound bar.
SPEAKER WIRE
To connect the Sound bar to an AV Receiver or Amplifier, high-quality 14 to 16 gauge stranded speaker wire is recommended. The wire may be connected directly to the speaker’s binding posts. Remember that you will need 2 runs of speaker wire to the Sound bar location as it contains the left and right speaker. Use the included DIN cable to connect the sound bar to a Sun Brite TV. See page 5 for more information.
CONTENTS
SB-AW-SNDBR-S-B
- (1)DIN cable w/90 cm cable for compatible SunBriteTVs
- (1) Speaker Mount Bracket Small
- (4) 1/4-20 x .25” Screws
- (4) 1/4-20 Flat Washers
SB-AW-SNDBR-M-B
- (1)DIN cable w/90 cm cable for compatible SunBriteTVs
- (1) Speaker Mount Bracket Large
- (2) 1/2” threaded standoff
- (2) 7/8” threaded standoff
- (4) 1/4-20 x .25” Screws
- (4) 1/4-20 Flat Washers
INSTALLATION
SPEAKER PLACEMENT
The SB-AW-SNDBR-S-B and SB-AW-SNDBR-M-B are designed to be the Left and Right speakers of a sound system. For most applications, placement should be below a flat ns creen TV using the included mounting bracket.
Installing on a SunBriteTV
The SB-AW-SNDBR-S-B, and SB-AW-SNDBR-M-B can be mounted directly above or
below Signature and Pro Series Sun Brite TVs (excluding the 84”) and below
Veranda Series Sun Brite TVs with the included bracket. The bracket attaches
the sound bar directly to the TV.
NOTE: The Strong™ universal bracket SM-SBAR-BKT-UNIV (available
separately) should be used when attaching the sound bar to any display other
than a Sun Brite TV.
- Remove the thumb screws and set the bracket in place.
- Replace the thumb screws to secure the bracket.
- Locate and remove the screws on the display to attach the bracket.
- The 55” Veranda and 65” Veranda and Signature displays require the included spacers to set the soundbar flush to the display.
- Screw the spacers into the display then set the bracket and sound bar in place and replace the screws to secure.
The table below outlines which standoff should be used with which SunBriteTV models.
NOTE: 43 inch model Sun Brite TVs do not require standoffs for installation.
Model Name | Model Number | Standoff Size |
---|---|---|
Veranda | 6574 | 7/8” Standoff |
Signature | 5584 | None |
Signature | 6584 | 1/2” Standoff |
Pro | 4917 | None |
Pro | 5518 | None |
CONNECTING AND CALIBRATING
Proper connections are important to the performance of any speaker within an audio system. Performing the following steps will ensure proper connections for optimum speaker performance:
- At each speaker connection, ensure that the outer jacket is separated by at least 2 inches.
- Strip the insulation on each conductor approximately ¼” and insert into the speaker terminals.
- Ensure that there are no stray strands of wire protruding from the connectors.
- Observe proper polarity (+ to + and – to – ) for each speaker and at the amplifier).
- Turn on the home theater receiver and calibrate all speakers in the system according to the receiver (or surround processor) manufacturer’s instructions.
Connecting to a Sun Brite TV
Connect the sound bar to Signature and Pro Model Sun Brite TVs using the
included 5 pin male connector wire (DIN Cable). Connect the wire ends as shown
in the diagram below.
Verifying Phase
When proper polarity is not maintained, the speakers play at the opposite ‘time’ from each other, or out of phase. The result is audio with lack of bass and vocals that sound thin or distant. If during or after calibrating your receiver you suspect the sound is not right and you cannot see any markings on the wire to verify polarity is correct, try this simple test:
-
Sit in the normal listening position for the system.
-
Play some music with your receiver set to Mono.
-
Listen to the music and observe the audio.
- Does the bass sound full and even with the other audio?
- Do the vocals sound centered and even in volume?
If either of the answers are YES, follow steps 3 and 4 with any other speakers in the system.
-
Turn off your receiver and reverse the connections for one of the speakers.
-
Repeat your test at the same volume level. When the sound has the loudest and best sounding bass, and vocals are centered and clear, your connections are correct and in-phase.
CLEANING
Use a dampened soft cloth or paper towel to clean the cabinet. The grill is best cleaned by brushing it off with a lint-free cloth.
SPECIFICATIONS
Product | SB-AW-SNDBR-S-B | SB-AW-SNDBR-M-B |
---|---|---|
Frequency response | 100 Hz-22 kHz | 95 Hz-22 kHz |
Color | Black | Black |
Connectors | Gold-Plated Push Terminals | Gold-Plated Push Terminals |
Dimensions (W x H x D) | 39” x 3.92” x 3” | 49.5” x 3.92” x 3” |
Sold as | Each | Each |
Weight | 11.5 lbs | 13.2 lbs |
Crossover Frequency | 2.3 kHz | 2.3 kHz |
Speaker Grille | Fixed Metal | Fixed Metal |
Nominal Impedance | 8 Ohm | 8 Ohm |
Power Peak | 225W | 225W |
Power RMS | 90W | 90W |
Sensitivity | 90 dB | 90 dB |
Tweeter | 1” Pure Titanium Dome | 1” Pure Titanium Dome |
Voice Coil | High Temp Voice Coil | High Temp Voice Coil |
Woofer | Per Channel- 2 x 3” Titanium Vapor Deposit Polypropylene Cone | Per |
Channel- 2 x 3” Titanium Vapor Deposit Polypropylene Cone
Passive Radiator| 2 x Titanium Vapor Deposit Polypropylene Cone| 3 x Titanium
Vapor Deposit Polypropylene Cone
TROUBLESHOOTING
These speakers are designed to function trouble-free. Most problems that occur are due to simple issues. If having trouble, contact Technical Support at 866-838-5052.
WARRANTY
Limited Lifetime Warranty
Sun Brite TV Sound bar Speakers have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to a designated service center with prior notification and an assigned return authorization number (RA).
CONTACTING TECHNICAL SUPPORT
As a thank you for purchasing SunBriteTV Electronics products, direct technical support services are available via phone. We encourage you to use this resource for any questions or concerns about our products. Visit our website for more support documentation. 866 838-5052 SunBriteTV.com
© 2017 Sun Brite Rev: 170801-1014
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>