BROAN F4030SF Under Cabinet Range Hood Convertible Instruction Manual

BROAN F4030SF Under Cabinet Range Hood Convertible

Product Information

Specifications:

• Product Name: F40000 SERIES 4-WAY CONVERTIBLE RANGE HOOD
• Manufacturer: Broan-NuTone LLC
• Intended Use: Domestic Cooking Only
• Installation Options: Ducted and Non-ducted (Ductfree)
• Mounting Height: 18-24 inches above the cooking surface

Product Usage Instructions

Planning Ductwork Installation:

1. Unpack the hood and check contents to ensure all parts are included.
2. Remove the round duct plate from the top of the hood and set it aside.
3. Remove the wiring box cover to access the mounting hardware.

Preparing the Range Hood:

1. If installing for ductfree use, remove the louver cover from the front of the hood.
2. Ensure louvers on the front of the hood are open and visible for ductfree mode operation.
3. Remove the appropriate electrical knockout based on the wiring entry point from the wall or cabinet.

Frequently Asked Questions

Q: Can this range hood be used for commercial cooking purposes?

A: No, this range hood is intended for domestic cooking only.

Q: What should I do if the motor of the hood keeps shutting off and restarting?

A: If the motor continues to shut off and restart, have the hood serviced to prevent any further issues.

Q: What is the recommended mounting height for optimal capture of cooking impurities?

A: The range hood should be mounted 18-24 inches above the cooking surface for best performance.

F40000 SERIES
4-WAY CONVERTIBLE RANGE HOOD

Register this product at www.broan-nutone.com/register.
For Warranty Statement, or to order Service Parts: go to www.broan- nutone.com and type the Model in the “Model Search” field at the top of the page.
Broan-NuTone LLC, 926 West State Street, Hartford, Wisconsin, USA
53027 800-558-1711

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT
For Non-ducted (Ductfree) Installation:

• a) Purchase non-ducted fi lter separately.
• b) Remove and discard damper/duct connector and louver cover (See Step 4) in “Prepare the Hood,” Page 2.
• c) Follow all steps except steps inside dotted lines.
  For Ducted Installation:
  Follow all steps, including steps inside dotted lines.

INTENDED FOR DOMESTIC COOKING ONLY.

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualifi ed person(s) in accordance with all applicable codes and standards, including fi re-rated construction codes and standards.
4. Suffi cient air is needed for proper combustion and exhausting of gases through the fl ue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with any solid-state speed control device.
8. To reduce the risk of fi re, use only metal ductwork.
9. Use with approved cord-connection kit only.
10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming foods.
3. Clean ventilation fans frequently. Grease should not be allowed to accumulate on fan or fi lter.
4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

1. SMOTHER FLAMES with a close-fi tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the fl ames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN – You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
4. Use an extinguisher ONLY if:
   • A. You know you have a Class ABC extinguisher and you already know how to operate it.
   • B. The fi re is small and contained in the area where it started.
   • C. The fi re department is being called.
   • D. You can fi ght the fi re with your back to an exit.

• Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.
4. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced.
5. For best capture of cooking impurities, your range hood should be mounted 18-24” above the cooking surface.
6. Please read specifi cation label on product for further information and requirements.

PLANNING DUCTWORK INSTALLATION

• Begin planning ductwork by deciding where the duct will run between the range hood and the outside. For best performance, use the shortest possible duct run and a minimum number of elbows. There are several choices shown – FIGS. 1A-1F.
• In more complex ducting situations, a 3-1/4” rectangular ducting range hood can be converted to a round duct by means of a transition.
• FIG. 1A. Ducting directly through the wall (for range hoods mounted on an exterior wall). Shown are two ways to duct through an outside wall. If a wall cap is used directly off the back of the hood, special care must be taken to make sure that the damper in the damper/duct connector on the hood and damper in the wall cap do not interfere with each other when the hood is operating. This could result in either inadequate air delivery or back drafts. If this condition does exist, remove the hood damper fl ap. Sometimes when using a wall cap it is easier to duct vertically and then use an elbow as shown in FIG. 1B.
• FIG. 1C. Ducting straight up through the roof using 3-1/4” x 10” rectangular duct. (For single story installations.)
• FIG. 1D. Ducting between the ceiling joists (for multi-story installations) or through the soffi t space above the cabinets (where the soffi t connects to an outside wall).
• FIG. 1E. Straight up through the roof using 3-1/4” x 10” to 6” round duct transition and 6” round duct (for single-story installations).
• FIG. 1F. Straight up through the roof using 7” round duct (for single-story installations).

PREPARING THE RANGE HOOD

1. Unpack hood and check contents. You should receive:

   • 1 – Aluminum Filter
   • 1 – 3-1/4” x 10” Damper/Duct Connector (mounted inside of hood for shipping only) (Save screws for mounting.)
   • 1 – 7” Round Duct Plate (mounted on top of hood) (not shown) (Save screws for mounting.)

2. Remove 7” round duct plate from top of hood. Set duct plate aside – with mounting screws.

3. Remove wiring box cover. Under cover find:

4. Plastic Bag containing loose mounting hardware
   For Ductfree Installations Only:

5. For ductfree installation, remove louver cover from front (or inside) of hood. (FIG. 3)
   NOTE
   Louvers on front of hood must be open and visible for hood to function in ductfree mode.

6. Remove either top or rear electrical knockout depending upon whether wiring will enter hood from wall or cabinet. (FIG. 4)

DUCTED INSTALLATION ONLY
NOTE
Louver cover must be installed as shown in Figure 3 to function in ducted mode.

6. Remove appropriate duct knockout on hood by inserting screwdriver into edge of knockout and breaking tabs holding knockout to hood. You may have to tap screwdriver with hammer to break tabs. Peel knockout back with pliers. (FIG. 5)

7. Fit damper/duct connector over opening and secure in place with black sheet metal screws. (FIG. 6)
   Hinge pins and damper/duct connector should be toward top of hood for ducting through wall or toward back of hood for ducting through cabinet above hood. Seal joint between damper/duct connector and hood with duct tape.

8. 7” round ducted discharge only: Re-install 7” round duct plate removed in Step 2 under “PREPARING THE RANGE HOOD” section. For best performance, line up the 7” round duct plate with the 7” round opening on hood. Mount duct plate to hood with 2 screws from duct plate and 2 screws from 3¼” x 10” damper. Install a 7” round damper (purchase separately). Damper fl ap must open freely in direction of air fl ow (away from range hood).

PREPARING THE INSTALLATION LOCATION

NOTE
MOUNT HOOD SO THAT BOTTOM OF HOOD IS 18”-24” ABOVE COOKING SURFACE. TOP FRONT EDGE OF HOOD SHOULD BE FLUSH WITH FRONT OF CABINET FRAME. IF DISTANCE BETWEEN WALL AND FRONT OF CABINET FRAME IS MORE THAN 12” THERE WILL BE A SPACE BETWEEN BACK OF HOOD AND WALL. THIS IS NORMAL.
OMIT STEP 9 if range hood will be installed under cabinets with fl ush bottom.

9. (For installation on recessed bottom cabinets only) Attach a wood filler strip at each side of recessed area under cabinet. (Use two 1” x 2” strips cut to length.) If recess is more than 1” use thicker strips. Attach strips with 1-1/4” screws about 3” from each end. See FIG. 7.
10. Measure and mark the following (FIGS. 7 & 8):

  * a) Electrical line opening
  * b) Duct opening

11. Drill four pilot holes in the corners of the marked duct opening as shown and cut the opening with a sabre saw or keyhole saw.
12. Use 1-1/4” drill bit to drill an opening for the electrical connection in wall or cabinet.
13. Hold the hood up against the cabinet bottom and trace keyhole slots onto the cabinet bottom of filler strips.
14. Screw the four supplied 7/8” wood screws for mounting the hood into the exact centre of the narrow end of the keyhole slots marked underneath the cabinet. Allow 3/8” of the screws to project, so the hood can be fi tted into place.

INSTALLING THE DUCTWORK
NOTE
THESE INSTRUCTIONS WILL FOLLOW THE PLANS MADE ON PAGE 2. START AT THE EXTERIOR AND RUN THE DUCT BACK TO THE RANGE HOOD.
FOR THE BEST PERFORMANCE OF YOUR RANGE HOOD, USE THE SHORTEST POSSIBLE DUCT RUN AND A MINIMUM NUMBER OF ELBOWS.
NEVER VENT A RANGE HOOD INTO AN ATTIC SPACE BECAUSE A BUILDUP OF GREASE WILL BECOME A FIRE HAZARD.
USE ONLY METAL DUCTWORK (DO NOT USE PLASTIC DUCT). ASSEMBLE SECURELY SO THAT IN CASE OF A GREASE FIRE ON THE RANGE, THE FIRE WILL BE CONTAINED INSIDE METAL DUCT WORK.
IT IS A GOOD PRACTICE TO TAPE ALL DUCT CONNECTIONS, MAKING THEM BOTH SECURE AND AIRTIGHT.

15. Follow the appropriate directions below for type of ductwork you are installing:

WALL CAPS (FIG. 9)
Use a saber saw to cut a hole slightly larger than duct so duct will line up easily with hood. Install casing strips on outside walls fi nished in siding. Assemble the duct work and tape all joints. Run duct work back to hood. Fasten wall cap to last section of duct and nail or screw cap to wall. Seal all around fl ange on wall cap with caulking compound. Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4” when the hood is installed.

ROOF CAPS
Cut hole in roof slightly larger than duct so duct will line up easily with hood. Trim shingles around hole so that they will fi t snugly around hood of cap when cap is installed. Assemble the ductwork and tape all joints. Run the ductwork down to hood. Trim duct parallel to roof pitch, leaving 3/4” of duct projecting above roof. Seal all around duct with roof cement.
Install roof cap, inserting back edge of cap under shingles. Seal around cap with roof cement and seal all nail heads and shingles that were cut or lifted.
Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4” when the hood is put into place.

INSTALLING THE RANGE HOOD

16. 16. Bring electrical cable through access hole drilled in wall or bottom of cabinet. Provide 6” wire leads and install proper connector for type of cable being used. Remove lock nut from connector and let prepared cable project through cabinet or wall opening so it is ready for installation into range hood. (FIG. 10)

17. Position hood in place so that:
    a) Electrical line is routed through the appropriate knockout opening. This step will have to be accomplished while positioning hood.
    b) Large part of keyhole mounting slots on hood fit onto hood mounting screws projecting from bottom of cabinet. (FIG. 11)

c) Damper/duct connector slides into ductwork in wall or cabinet.

18. Adjust hood so the front of hood is fl ush with cabinet front.
19. Tighten the four hood mounting screws securely.
20. Install locknut on electrical connector and tighten securely.
21. Make electrical connection using wire nuts to connect white wire to white, black wire to black. Ground hood to prepared hole using green ground screw provided. (FIG. 12)

22. Replace wiring box cover and screw. Make sure that all wiring is safely contained inside.

NOTE
For Ductfree Installations Only:

Install both fi lters. Make sure that ductfree filter (purchase separately) is next to fan assembly with blue side next to blade. Aluminium filter should be facing out.

USE AND CARE

• SWITCHES
  The fan and light are each controlled by a rocker switch. The light switch has two positions, “ON” and “OFF”. The fan switch has three positions – “HIGH”, “LOW” and “OFF”. ( “OFF” is the middle position.)

• CLEANING
  Finish. Keep your range hood clean using a mild detergent suitable for painted surfaces.
  Aluminium Filters should be cleaned frequently with a detergent solution to avoid grease build-up. They are also dishwasher safe.

• FILTER REMOVAL
  Remove fi lter by turning fi lter clip to the side and lifting fi lter out. In ducted version, turn the retaining clip to one side and place aluminum filter over embossed retaining tabs on back of fan housing. Turn filter clip so that the low end of clip holds single filter firmly in place. (FIG. 13)

In the non-ducted version, place non-ducted fi lter (non-ducted filter to be purchased separately, model 41F) over tabs on back of fan housing. Turn filter retaining clip so that high end holds filter fi rmly in place. Make sure blue side of the non-ducted fi lter is next to fan blade.
NOTE: Make sure that arrows on fi lter retaining clip point toward back and front of hood.

• LIGHT BULB REPLACEMENT
  LED light bulb (not supplied with hood) should be A19, 15 watts maximum, E26 base. The lens covering bulb is removed by pressing the two extending tabs together until they release from the retaining slots. (FIG. 14)

• FAN ASSEMBLY REMOVAL
  Be sure power is disconnected. Remove fi lters. Remove the two screws holding the motor bracket to the range hood and unplug the fan assembly. Be careful not to allow fan assembly to drop when the screws are removed. (FIG. 15).

References

• Product Registration
• Broan-NuTone | Better Air. Better Life.
• Product Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>