SEALEY VS2006.V3 Ratchet Type Axle Stands 6 Tonne Capacity PER Stand Instructions
- June 4, 2024
- SEALEY
Table of Contents
RATCHET TYPE AXLE STANDS (PAIR) 6TONNE
CAPACITY PER STAND
MODEL NO: VS2006.V3
VS2006.V3 Ratchet Type Axle Stands 6 Tonne Capacity PER Stand
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions,
and properly maintained, giving you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instructions
SAFETY
WARNING!
DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE
DAMAGE TO, OR FAILURE OF THE AXLE STANDS. POSITION LOAD ON THE CENTRE OF THE
CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD-LEVEL SURFACES CAPABLE
OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD-LEVEL SURFACES CAN
RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON
TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE
STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR
LOSS OF LIFE.
▲ DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER
LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE
STANDS.
Use only as specified by the manufacturer.
Ensure the load does not exceed the maximum capacity as marked on the axle
stand, per pair.
Use no more than a single pair of stands either on the front, rear or one side
of the vehicle. Use in pairs.
No alterations or modifications shall be made to this product.
Use on a hard, level surface, e.g. concrete. DO NOT use on uneven ground or
tarmacadam.
Securely chock wheels in contact with the ground. Before jacking and placing
the stands, apply the vehicle handbrake (put automatics in ‘Park’).
Make sure that each stand is securely located under a strong point on the
vehicle; consult the vehicle manufacturer’s handbook for guidance. Ensure that
the height adjust locking mechanism is fully located before applying any load
to the axle stand.
Ensure that the load is located centrally on the saddle and that the weight is
directed through the vertical axis of the stand.
Exercise extra care when using a three-wheeled vehicle or a trailer. Refer to
the vehicle manufacturer’s instructions.
Once the vehicle is supported, ensure that the vehicle and stands are stable
before starting work. Ensure that it is not possible for the vehicle to move
before commencing any work.
Inspect stands before each use. DO NOT use if they show signs of damage. DO
NOT use if it is suspected that they have been overloaded.
Before commencing any work or going beneath the vehicle, undertake a risk
assessment. Ensure that a responsible person is aware of the work about to be
undertaken.
Replace any labels on the axle stand should they become unreadable. This
applies in particular to any warning or operation instruction labels. If
replacement labels are required, contact your Sealey stockist.
DO NOT use axle stands on the highway, or anywhere else if it is deemed to be
unsafe.
DO NOT push or twist the vehicle/load whilst it is supported on stands.
DO NOT mix components between stands. Use only as supplied.
DO NOT allow children or animals in the vicinity of a vehicle supported on
axle stands.
DO NOT leave a vehicle on axle stands in an area that could be considered a
hazard to others or property.
FOLLOW STEPS 1, 2, AND 3 TO CORRECTLY PLACE THE VEHICLE / LOAD ONTO AXLE
STANDS.
INTRODUCTION
Ratchet-type axle stands, with cast iron support posts. Features angled teeth in posts, which prevent accidental release of the load, the more weight applied, the tighter the post is locked. Sold in pairs.
SPECIFICATION
Model no: ……………………………………………………. VS2006.V3
Capacity each: ………………………………….. 6 tonnes (6,000 kg)
Capacity Pair: ………………………………… 12 tonnes (12,000 kg)
Min. Height: ………………………………………………………. 414mm
Max. Height: ……………………………………………………… 605mm
ASSEMBLY
4.1. Insert the centre column into the base frame and stand (fig.1).
4.2. Ensure the toothed side of the column will engage with the locking lever
mechanism (fig.2).
4.3. Bend in the locking tab using a drift or similar and a hammer (fig.3).
4.4. Check the base frame and stand is in good condition and have not suffered
damage during transit.
OPERATION
5.1. Refer to the manufacturer’s instructions for recommended jacking/support
points.
5.2. Check to ensure jacking/support points are in good condition. Position
the stands beneath their support points.
5.3. To adjust the stands:
5.4. Hold the control lever up while lifting the centre column to the required
height. Push the control lever down to lock the pawl into the central column
teeth (fig.1 and fig.2).
WARNING! ENSURE THE PAWL IS FULLY ENGAGED WITH THE TEETH.
5.5. Carefully and slowly lower the vehicle onto the stands. Ensure load-
bearing points sit in the centre of the saddles and that the stands are
stable.
5.6. Also ensure that there are no objects or persons that could impede the
safe lowering of the vehicle onto the stands.
▲ DANGER! You must follow instructions carefully and ensure you DO NOT load
the stands off the centre. Failure to adhere to these warnings may cause
damage, injury or loss of life!
5.7. Store the stands in their lowest position.
MAINTENANCE
6.1. Before each use, check that stands and stand welds are not cracked and
that there are no missing or damaged parts.
6.2. Any suspect axle stands must be removed from service immediately
6.3. Due to the potential hazards associated with stands, do not misuse or
make any modification to, the stands or components
6.4. It is the responsibility of the owner to ensure that the operator has
read these instructions together with the safety features on the side of the
stand and that the operator is aware of the stand’s uses and limitations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of
which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>